FRANCO UF Mobile Instruction manual

INSTRUCTION MANUAL FOR
USE AND MAINTENANCE
UF Mobile
HUMIDIFIER/COOLER
TRANSLATION OF ORIGINAL INSTRUCTIONS
ENGLISH
Read this manual carefully before
installing and operating the machine
Rev. 00/2022 Franco s. r. l. - Via Nazionale, 80 - 12010 Cervasca (CN)

Operation and Maintenance Manual - UF Mobile
2
INDEX
INDEX.......................................................................................................................................2
1 - INTRODUCTION .................................................................................................................3
1.1 General safety warnings.........................................................................................................3
1.2 Guidelines for the correct disposal of the product ..................................................................3
1.3 Conventions used in this manual............................................................................................3
1.4 Keeping and updating the instruction manual.........................................................................4
1.5 Target readers........................................................................................................................4
1.6 Pictograms .............................................................................................................................5
1.7 Applications............................................................................................................................7
1.8 Versions .................................................................................................................................7
1.9 Machine identification and number plate data........................................................................7
1.10 Description of equipment......................................................................................................8
1.11 Transport and handling.........................................................................................................8
1.12 Warranty...............................................................................................................................9
1.13 Manufacturer's identification data.........................................................................................9
1.14 Declarations .........................................................................................................................9
1.15 EC Declaration of Conformity.............................................................................................10
2 - INSTALLATION ................................................................................................................11
2.1 Preliminary operations..........................................................................................................11
2.2 Positioning............................................................................................................................11
2.3 Electrical connections...........................................................................................................12
2.4 Water supply ........................................................................................................................12
3 - OPERATION .....................................................................................................................12
3.1 Preliminary operations..........................................................................................................12
3.2 First start-up.........................................................................................................................12
3.3 Start-up and operation..........................................................................................................13
3.4 Adjustment of the water flow rate .........................................................................................13
3.5 Stop......................................................................................................................................13
4 - MAINTENANCE ................................................................................................................14
4.1 Cleaning the disc..................................................................................................................14
4.2 Cleaning of tank ...................................................................................................................14
4.3 Replacing and cleaning the pump ........................................................................................15
4.4 Replacing the rotating disc...................................................................................................15
4.6 Replacing the nozzle............................................................................................................16
4.7 Accessories..........................................................................................................................16
5 - TECHNICAL SPECIFICATIONS.......................................................................................17
5.1 Technical data......................................................................................................................17
5.2 Overall dimensions...............................................................................................................17
5.3 Electrical diagram.................................................................................................................18
6. SPARE PARTS LIST..........................................................................................................19
7. TROUBLESHOOTING GUIDE ...........................................................................................23

Operation and Maintenance Manual - UF Mobile
3
1 - INTRODUCTION
1.1 General safety warnings
This appliance must only be used for the function for which it was designed: "Adiabatic humidifier/cooler".
Any other use is to be considered improper and dangerous. Franco s.r.l. cannot be held responsible for any
damage resulting from improper, incorrect and unreasonable use or if the appliance is used in installations
which do not comply with the safety regulations in force.
- Check the integrity of the appliance when you open the packaging, paying particular attention to the
presence of damage or deformation to the plastic parts which may lead to breakage and/or malfunction during
use. In such cases, do not connect the machine to the mains power supply. Periodically carry out a general
inspection of the machine.
- Before connecting the appliance, make sure that the data on the rating plate correspond to those of your
electrical system. The data label (see par. 1.9) is located on the side of the appliance.
- Comply with the safety rules indicated for electrical equipment, and in particular:
•Follow the installation instructions of the appliance.
•Do not place objects on the humidifier.
•Prevent children and/or incapacitated persons from using the device without proper supervision.
•Do not touch the humidifier during operation or while the disc is stopped.
•Never immerse the appliance in water or any other liquid.
•Do not place any objects inside the tank as this could cause irreparable damage to the appliance.
•Do not use accessories, spare parts or components not intended for or supplied by the manufacturer.
•Avoid touching the appliance with wet or damp hands
•Do not pull power cables or expose them to risk of shearing.
•Do not leave the appliance exposed to the elements (rain, sun, etc.).
•In the event of a fault or malfunction of the appliance, switch it off immediately and disconnect the
power supply. Do not attempt to open or tamper with the appliance: contact a qualified technician.
•Do not attempt to fill or empty the tank when the appliance is in operation.
1.2 Guidelines for the correct disposal of the product
Pursuant to European Directive 2012/19/EU:
At the end of its useful life, the product must not be disposed of with municipal waste.
It can be handed in at the separate waste collection points set up by the municipalities, or
at retailers who provide this service. Disposing of the product separately avoids possible
negative consequences for the environment and for health deriving from its improper
disposal and allows the recovery of the materials of which it is composed in order to obtain
a significant saving of energy and resources. To emphasise the obligation to dispose of
electrical and electronic equipment separately, the product is marked with a crossed-out wheeled bin.
1.3 Conventions used in this manual
The manual is divided into chapters. The operators to whom the instructions are addressed are specified,
where necessary, in order to operate the machine safely.
The sequence of chapters follows to the temporal sequence of the machine's life.
To facilitate immediate understanding of the text, terms, abbreviations and pictograms are used, the meaning
of which is indicated below.

Operation and Maintenance Manual - UF Mobile
4
ABBREVIATIONS
Cap. = Chapter
Par. = Paragraph
Page = Page
Fig. = Figure
Tab. = Table
UNITS OF MEASUREMENT
The units of measurement used are those of the International System (SI).
1.4 Keeping and updating the instruction manual
The instruction manual must be kept with care and must always accompany the machine during its life. Parts
must not be removed, torn or arbitrarily modified.
The manual should be stored in an environment protected from moisture and heat and in the immediate
vicinity of the machine to which it relates. The manufacturer can provide additional copies of the machine
instruction manual at the request of the user.
You can make a request by writing to [e-mail]
The manufacturer reserves the right to modify the design and make improvements to the machine without
informing the Customer, and without updating the manual already delivered to the user. However, in the
event of changes to the machine installed at the Customer's premises, agreed with the manufacturer and
which involve the modification of one or more chapters of the instruction manual, it will be the manufacturer's
responsibility to send the affected users the chapters affected by the change.
It is the responsibility of the User to replace the old chapters, the start page and the table of contents with the
new ones in all copies owned.
The Manufacturer is responsible for the original version in Italian; in the event of any doubts regarding the
translated versions, please refer to the Italian language and contact the manufacturer
([e-mail]) for due verification.
1.5 Target readers
This manual is intended for the installer, the operator and qualified personnel authorised to service the
machine.
OPERATOR: meanstheperson or persons responsible for installing, operating, adjusting, cleaning, repairing
and moving machinery and for carrying out the simplest maintenance operations.
QUALIFIED PERSONNEL/QUALIFIED WORKERS: these are people who have attended specialised
courses, training, etc. and have experience in the installation, commissioning and maintenance, repair,
transport of the machine.
The machine is intended for industrial use, and therefore professional and not general use, so its use must
be entrusted to qualified personnel, in particular who:
•have reached the age of majority;
•are physically and mentally fit to carry out work of particular technical difficulty;
•have been properly instructed in the use and maintenance of the machine;
•have been judged by the employer to be suitable for the task;
•are able to understand and interpret the operator's manual and safety instructions;
•are familiar with emergency procedures and their implementation;
•have the ability to operate the specific type of equipment;
•are familiar with the specific rules of the case;
•have understood the operating procedures defined by the machine manufacturer.

Operation and Maintenance Manual - UF Mobile
5
The appliance may be used by persons with reduced physical, sensory or mental capabilities, or lack of
experience or knowledge, provided that they are supervised or have received instructions concerning the
safe use of the appliance and an understanding of the hazards involved.
1.6 Pictograms
This section explains the meaning of the pictograms indicating the operator's qualification, the state of the
machine, the hazards and the obligations/prohibitions to be respected. Their use makes it possible to provide
rapid and unambiguous information necessary for the correct and safe use of the machine.
PICTOGRAMS RELATING TO OPERATOR QUALIFICATION
Symbol
Description
General labourer: operator without specific skills, able to carry out only simple tasks on the
instructions of qualified technicians.
Driver of lifting and handling equipment: an operator qualified to use lifting and handling
equipment and machines (strictly following the manufacturer's instructions), in accordance
with the laws in force in the country of the machine user.
Mechanical maintenance technician: qualified technician, able to operate the machine
under normal conditions, to make it work with protections disabled, to intervene on the
mechanical parts to carry out the necessary adjustments, maintenance and repairs.
Typically, he is not qualified to work on live electrical installations.
Electrical maintenance technician: qualified technician, able to operate the machine under
normal conditions, to run it with protections disabled, is in charge of all electrical adjustment,
maintenance and repair work. He is able to work in the presence of voltage inside cabinets
and junction boxes.
Manufacturer's technician: a qualified technician made available by the manufacturer to
carry out operations of a complex nature in particular situations or, in any case, as agreed
with the user. The skills are, depending on the case, mechanical and/or electrical and/or
electronic and/or software.

Operation and Maintenance Manual - UF Mobile
6
SAFETY PICTOGRAMS (ISO 7010)
Pictograms contained within a triangle indicate DANGER.
Pictograms contained within a circle impose a PROHIBITION/OBBLIGATION.
Pictogram
Description
Dangerous electrical voltage.
General danger.
Do not remove safety devices.
It is forbidden to clean, oil, grease, repair or adjust
moving parts by hand.
Obligation to switch off power before starting work
or repairs.
Protective gloves are mandatory.
Mandatory safety footwear.
Helmet mandatory.

Operation and Maintenance Manual - UF Mobile
7
1.7 Applications
The UF Mobile can be used for humidification in several types of medium to large agricultural, industrial or
commercial premises.
The device can also be used as an adiabatic cooler. This is possible because atomised water in contact
with ambient air tends to evaporate, removing heat and lowering the temperature. The cooling capacity
depends on temperature, ambient humidity and air distribution.
The UF Mobile is mounted on a trolley with an integrated water tank, which allows the machine to be easily
moved within the room to be humidified or cooled according to the Customer's needs, ensuring maximum
versatility of use.
This machine must only be used for the purpose
for which it was designed:
HUMIDIFICATION / ADIABATIC COOLING
All other uses are improper and potentially dangerous.
1.8 Versions
The UF Mobile humidifier is available in the following version:
1959550 UF Mobile, with airflow rate of 8000 m³/h, 230V ~ 50Hz
1.9 Machine identification and number plate data
Each machine is identified by a CE nameplate on which the article code, serial number and technical data of
the machine are indelibly marked (Fig. 1.9.1).
Always quote these references for any communication with the manufacturer or service centres.
Fig.1.9.1 CE nameplate

Operation and Maintenance Manual - UF Mobile
8
1.10 Description of equipment
Main components (Fig. 1.10.1)
Fig. 1.10.1
1.11 Transport and handling
The unit is packed on a pallet, with protective film and fixing straps.
Take great care when unpacking to avoid damage to components. Check the integrity of the
machine by checking thatthere are no visibly damaged parts. Do not disposeof thepackaging
elements in the environment: they must be placed in special collection areas.
The UF Mobile is a wheeled unit that can be moved horizontally on flat surfaces without the
aid of lifting and transport equipment.
ATTENTION! Before making any moves:
a. stop the machine;
b. Disconnect the machine from the mains;
To lift the machine, use a suitable means (transpallet, forklift truck, etc.). The weight is indicated on the
nameplate and in the technical data table (see Par. 5.1).
Rotary disc
Disc
cap
Rear
cover
Nozzle
Fixed disk
Protection
grille
Water tray
Electric
box
Air outlet grille
Fan
Humidifier
support bracket
Tank
Trolley
Air inlet grille
Pump

Operation and Maintenance Manual - UF Mobile
9
1.12 Warranty
This appliance is guaranteed for 12 months from the date of manufacture for all faults attributable to a proven
manufacturing or material defect. The warranty does not cover all parts damaged by transport, bad or
incorrect maintenance, neglect, inability to use, improper use, tampering by unauthorised personnel and, in
any case, causes beyond the control of Franco s.r.l.. During the warranty period, Franco s.r.l. undertakes to
supply free of charge those parts that should prove to be defective at the origin.
The intervention must be carried out by an authorised and qualified technician.
1.13 Manufacturer's identification data
Manufacturer
FRANCO s.r.l.
Legal - administrative headquarters
VIA NAZIONALE, 80 - 12010 CERVASCA (CN) - ITALY
Contact
Tel.: [phone] - 61.16.63
Email: [e-mail]
Web: francosrl.com
1.14 Declarations
The machine to which this manual refers is manufactured in accordance with the relevant European
Community legislation applicable at the time of its placing on the market.
The machine is not included among those mentioned in Annex IV of Directive 2006/42/EC.

Operation and Maintenance Manual - UF Mobile
10
1.15 EC Declaration of Conformity
THE MANUFACTURER
FRANCO s.r.l.
Company
Via Nazionale, 80 12010 CN
Address Postcode Province
Cervasca Italy
City State
DECLARES under its own responsibility that the machine
Humidifier / Cooler UF Mobile
Description Model
1959550
Article number
UF Mobile Humidifier/Refrigerator
Trade name
Room humidification/cooling
Intended use complies with the following European Directives:
2006/42/EC Machinery Directive
(2014/35/EU) (Low Voltage Directive)
2014/30/EU Electromagnetic Compatibility Directive
Harmonised standards and reference specifications used:
EN 12100:2010
EN 60335-1:2012 + A11 +A13 +A1 + A14 + A2 +A15:2021
EN 60335-2-98:2003/A11:2019
EN 60335-2-41:2003/A2:2010
EN 60034-1:2010
EN 55014-1 :2017, EN 55014-2:2015, EN 61000-6-1:2016, EN 61000-6-3:2010
Legal entity authorised to establish the Technical File:
FRANCO s.r.l.
Name
Via Nazionale, 80 12010 CN
Address Postcode Province
Cervasca Italy
City State
Place and date of document
The manufacturer
Cervasca, 05/04/2022
Signature
Rev. 00/2022
Marco Fantino
Administrator

Operation and Maintenance Manual - UF Mobile
11
2 - INSTALLATION
2.1 Preliminary operations
In order to operate the UF Mobile humidifier, the following is required:
•Electrical network with voltage and frequency characteristics suitable for the machine, with earthing and
protective devices;
•Ambient temperature during operation: must be between 1°C and 40°C
•Temperature of the water and liquids used: must not exceed 35°C.
•Drinking water with low fixed residue or treated water. The quality of the water affects the frequency of
maintenance operations and the correct functioning of the humidifier.
In particular, follow the requirements of standard UNI 8884 "Characteristics and
treatment of water in cooling and humidification circuits", which stipulates a
conductivity of less than 100 μS/cm and a total hardness of less than 5°fH (50 ppm of
CaCO3), or another equivalent national standard, to avoid the accumulation of limescale
deposits or incrustations that could compromise the proper operation of the appliance.
2.2 Positioning

The UF Mobile humidifier must be placed on a flat and level surface, in a horizontal position. When the
machine is in the desired position, lock the rear braked wheel before starting it.
Observe the minimum recommended distances for correct machine operation.
To avoid the formation of condensation, maintain a distance of at least 1m between the humidifier and
surrounding walls. The distance from the wall in front of the machine should be evaluated according to the
size of the room and the humidification or cooling requirements.
The unit is supplied as standard with grilles to protect the rotating parts (centrifugal disc, fan).
Do not remove the protective guards. Respect the safety distances from moving
parts prescribed by the UNI EN ISO 13857:2008 standard. Any maintenance or
repair operations requiring the removal of protections must be carried out
exclusively by qualified personnel, after having stopped the machine and
disconnected the power supply.

Operation and Maintenance Manual - UF Mobile
12
2.3 Electrical connections
•Ensure that the electrical installation to which the appliance is connected complies with
the electrical safety regulations in force in the country of destination.
•Ensure that the supply voltage ratings comply with the ones shown on the nameplate
of the appliance.
•Earthing is mandatory.
The unit is supplied as standard with a power cable with Schuko plug to be connected to a 230V 50Hz single
phase socket with earth. Two ON/OFF switches are provided on the unit for separate control of fan and
humidifier.
2.4 Water supply
Manually fill the machine's built-in tank (120 litre capacity) with clean tap water from the water mains. For the
specifications of the water to be used, see paragraph 2.1. During operation, regularly check the water level
in the tank on the graduated scale and top up when necessary.
3 - OPERATION
3.1 Preliminary operations
Before operating the humidifier, check that:
•The appliance is placed in a stable, flat and level position, with the wheel brake locked;
•The power cable is correctly connected to a grounded outlet;
•The power cable is correctly positioned and not squashed or overstretched;
•The humidifier is free and clean;
•The water tank contains water;
•The water supply and return pipes are connected.
3.2 First start-up
•Set the fan and pump switches to I (ON) (Fig. 3.2.1).
•Check the correct direction of the air flow and the direction of rotation of the disc (Fig. 3.2.2).
•Open the water control valve and check that there are no leaks in the circuit.
Fig. 3.2.1 Fig. 3.2.2
The pump must never run dry. Add water to the tank regularly during operation to avoid
damaging the pump.
The temperature of the liquids used must not exceed 35°C.
Fluu
Fluss
o
dell’a
ria

Operation and Maintenance Manual - UF Mobile
13
3.3 Start-up and operation
Use the ON/OFF switches to start the fan and pump. The pump, located at the bottom of the tank, circulates
the water to the rotating disc, which nebulises it, and the fan generates a flow of air that distributes the mist
into the room. The water that has not been atomised collects in the tray and is returned to the tank through
the return pipe.
For ventilation only, set the humidifier switch to 0 (OFF).
During operation:
•Check the water level in the reservoir regularly on the graduated scale and top up according
to the water consumption of the humidifier.
•Do not move the appliance while it is operating. Switch off and unplug the appliance before
moving it.
•Do not disconnect the power cable of the pump while the machine is powered. The pump
should only be disconnected when the machine is switched off and unplugged, for cleaning and
maintenance.
•In the event of a stoppage or other malfunction, refer to Chapter 7 "Troubleshooting".
3.4 Adjustment of the water flow rate
Adjust the water flow rate by adjusting the regulating valve on the delivery
pipe until fine mist is obtained without droplets being dragged from the
rotating disc. Centrifugal humidifiers produce droplets of varying sizes, on
average between 10 and 30 mm. The size of the droplets produced depends
on the setting of the flow rate and the environmental conditions.
The UF Mobile can atomise up to a maximum of 40 l/h of water. However, an
excessive water flow rate could result in an increase in droplet size and adversely affect the quality of the fog.
3.5 Stop
After use:
•Switch off the machine by setting the switches to the '0' (OFF) position;
•Disconnect the plug;
•Empty the tank completely by removing the drain plug at the bottom on the front side, after positioning the
appliance above a suitable drainage point.
ATTENTION!
Stagnant water can cause the growth of bacteria and microorganisms that are harmful to
health. It is therefore essential to prevent stagnation.
Drain the water from the tank regularly after use. Never leave stagnant water in the tank
when the machine is not in use. (see also par. 4.2. "Cleaning the tank and reservoir").
As well as for safety reasons, regular water renewal is also necessary to keep the appliance clean
and free from limescale, mould, etc.
OPEN
CLOSED

Operation and Maintenance Manual - UF Mobile
14
4 - MAINTENANCE
The operations described in this chapter must only be carried out by authorised and qualified
personnel, using suitable personal protective equipment. Before carrying out any work, disconnect
the appliance from the electricity and water supplies.
Periodically check the water flow to the rotating disc. Adjust the flow regulator if necessary. Keep discs, tank
and internal parts clean to avoid dirt build-up.
4.1 Cleaning the disc
•Keep the discclean to prevent limescale build-up or dirt accumulation that could cause increasedvibration
or coarse spraying.
•To clean the rotating disc, use a soft, damp cloth and a non-toxic, solvent-free cleaning agent, wiping
without applying excessive pressure.
•Do not use solvents.
•The fixed disk should becleaned with a brushwith stiff bristles, rubbing the teeth taking care not to damage
them. Any limescale deposits can be removed with vinegar, lemon or another specific, non-toxic, solvent-
free product.
4.2 Cleaning of tank
Emptying the tank and renewing the water (after each use)
•Place the appliance over a suitable drainage point and unscrew the front drainage cap of the tank to
completely remove the water contained.
•When the operation is complete, be sure to reinsert and tighten the drain plug.
•Before using the machine again, fill the tank with clean tap water.
Complete tank cleaning
If more thorough cleaning of the tank is required, disconnect the pump power cable, disconnect the
discharge pipe from the pump, remove the discharge and return pipes and remove the tank from the trolley
to facilitate cleaning.
•Clean the inside of the tank using a non-toxic, solvent-free cleaning agent, if necessary using a
pressurised water jet to remove any dirt, scale, etc. that is particularly difficult to remove.
•Rinse and reposition the tank on the trolley, making sure to reinsert the drain plug and reconnect the
pump power cable and the delivery and return hoses.
Cleaning the drip tray
•Inspect and clean the drip tray periodically.
•To access the tray, unscrew the two screws securing the cover and remove it.
•Clean the inside of the tub with a cloth or sponge, rubbing the walls gently. Do not use solvents.

Operation and Maintenance Manual - UF Mobile
15
4.3 Replacing and cleaning the pump
To replace the pump, proceed as follows:
•Disconnect the power cord of the pump;
•Remove the tank cover;
•Disconnect the pump from the bottom of the tank and pull it out through the filling hole;
•Disconnect the discharge pipe from the pump to be replaced and connect it to the new pump;
•Insert the pump into the tank and secure it to the bottom using the suction cups;
•Reconnect the power cord and start the machine to check operation.
The pump does not require any special maintenance. However, it is advisable to clean the internal rotating
parts periodically, depending on the quality of the water used. For this purpose:
•Disconnect and remove the pump from the tank as described above;
•Remove the pressure pipe, using a screwdriver if necessary;
•Remove and check the rotor and impeller and clean them with lukewarm water and a brush. Any limescale
deposits can be removed with vinegar, lemon or special products. Do not use solvents;
•Refit the nozzle, reposition the pump inside the tank and reconnect the connector on the power cable.
4.4 Replacing the rotating disc
•Remove the front protection grille by unscrewing the 3 fixing screws.
•Remove the central cap of the rotating disc by pushing it out with a small slotted screwdriver (Fig. 4.4.1).
•Using a screwdriver (hex. 7), loosen the M4x16 fixing screw of the rotating disc to the motor shaft and its
washer (Fig. 4.4.2).
Fig. 4.4.1 Fig. 4.4.2
•Insert the M8x40 screw supplied with the machine into the central hole of the rotating disc
(Fig. 4.4.3)
•Use a screwdriver (hex. 13) to tighten the screw, which will push the disc out effortlessly when
it enters the hole. (Fig. 4.4.4)
Push out
inside the slot
Screw M4x16

Operation and Maintenance Manual - UF Mobile
16
Fig. 4.4.3 Fig. 4.4.4
•Once the disc has been removed, remove the M8x40 screw by unscrewing it from the rotating
disc.
•Apply a small amount of grease to the motor shaft and fit the new disc, making sure the keys
are aligned and centered, without tapping or forcing. Replace the washer, M4 screw and plug.
Check that the 4 mm thick spacer (see section 5.3 "Spare parts list" item 5) is correctly
positioned between the fixed and rotating discs.
4.6 Replacing the nozzle
•After removing the rotating disc (see section 4.4), remove the nozzle by unscrewing the two fixing
screws.
•Push the grey ring on the elbow connector (see section 5.3 "Spare parts list" item 19) to the rear of
the disc and, while holding it down, pull the nozzle to be replaced.
•Position the new nozzle by repeating the sequence in reverse.
4.7 Accessories
A full range of accessories for your UF Mobile is available on request.
Ask your supplier for the accessories catalogue for more details.
Screw M8x40

Operation and Maintenance Manual - UF Mobile
17
5 - TECHNICAL SPECIFICATIONS
5.1 Technical data
Atomisation capacity
l/h
up to 40
Power supply
~ single-phase
IP rating
IP55
Weight
kg
77
Airflow rate
m³/h
8000
Fan
Power
W
460
Voltage
V/Hz
230/50
Current
A
2,2
Humidifier
Power
W
190
Voltage
V/Hz
230/50
Current
A
1,5
5.2 Overall dimensions

Operation and Maintenance Manual - UF Mobile
18
5.3 Electrical diagram
Check that the electrical ratings of the power supply system comply with the data plate.
Install a magnetothermal differential circuit breaker in the circuit upstream of the equipment.
MV Fan motor
MU Humidifier motor
MP Pump motor
Also make sure that:
- the power plug has been inserted into a grounded single-phase 230V ~ 50Hz outlet;
- all applicable safety regulations have been complied with.
If the power cable is damaged, it must be replaced by the manufacturer or his technical service or a similarly
qualified person, to prevent any risk.

Operation and Maintenance Manual - UF Mobile
19
6. SPARE PARTS LIST
GENERAL ASSEMBLY
Use only original spare parts.
When ordering spare parts, always specify:
•Machine model •Year of construction/No. of
series
•Part number
•Quantity •Shipping address

Operation and Maintenance Manual - UF Mobile
20
Pos.
Code
Description
Qty
1
6002004
SCREW 4.2x9.5 DIN 7981
3
2
1801030
PROTECTION GRILLE (10mm pitch)
1
3
1800003
ROTARY DISC CAP
1
4
6001001
SCREW M4x16 DIN 933
1
5
1801006
ROTARY DISC FIXING WASHER
1
6
1800060
ROTARY DISC
1
7
1801008
ROTARY DISC SPACER 4mm
1
8
6002000
SCREW 4.2x13 DIN 7982
3
9
6001502
SCREW M6x20 DIN 7991
4
10
6001501
SCREW M4x16 DIN 7991
4
11
6003000
WASHER 4.3x9 DIN 125
4
12
6002500
NUT M4 DIN 934
4
13
1800022
NOZZLE
1
14
6002003
SCREW 2.9x9.5 DIN 7981
2
15
1800061
FIXED DISC
1
16
6002002
SCREW 2.9x19 DIN 7982
2
17
1800017
TRAY COVER (GREEN)
1
18
1909502
WATER TANK 120L
1
19
7308018
230V 50Hz PUMP
1
20
1800063
WATER TRAY (GREEN)
1
21
7307008
CONNECTOR + CABLE KIT
1
22
8202000
VALVE 3/8"
1
23
1909501
COMPLETE TROLLEY
1
24
7303005
CABLE GROMMET
1
25
8202008
STRAIGHT FITTING F 1/2"- 3/8"
1
26
3102005
3/8" SUPPLY/RETURN PIPE KIT
1
27
8202009
3/8" ELBOW CONNECTOR
1
28
1800062
REAR COVER
1
29
5001500
MOTOR 230V 50Hz
1
30
1909504
FAN SUPPORT
1
31
1909503
COMPLETE ELECTRICAL BOX
1
32
7004000
POWER CABLE + PLUG
1
33
1709001
CONNECTION BRACKET HUMID./VENT.
1
34
1606102
FAN ASSEMBLY
1