FRANCO UCP Series Instruction manual

INSTRUCTION MANUAL FOR USE
AND MAINTENANCE
UCP
CENTRIFUGAL
HUMIDIFIER
TRANSLATED VERSION FROM ITALIAN TO
E N G L I S H
Before installing or running the unit,
it is mandatory to carefully read and consult this manual.

FRANCO srl Manual of use and maintenance UCP
2
Manual version: 02-000/2010 Franco srl –Via Nazionale, 80 12010 Cervasca (CN), Italy
INDEX
INDEX ......................................................................................................................................2
1 - INTRODUCTION.................................................................................................................3
1.1 General warnings............................................................................................................3
1.2 Instructions for proper disposal of the product................................................................3
1.3 Conventions used in this manual....................................................................................4
1.4 Instruction manual conservation.....................................................................................4
1.5 Recipients.......................................................................................................................5
1.6 Glossary and pictograms................................................................................................5
1.7 Applications ....................................................................................................................9
1.8 Versions..........................................................................................................................9
1.9 Identification and data label of the unit ...........................................................................9
1.10 Parts description......................................................................................................... 10
1.11 Transport and handling...............................................................................................10
1.12 Warranty.....................................................................................................................11
1.13 Manufacturer’s identification data ...............................................................................11
1.14 Declarations................................................................................................................ 11
1.15 Declaration of incorporation........................................................................................12
2 - INSTALLATION................................................................................................................ 13
2.1 Before installing............................................................................................................ 13
2.2 Positioning....................................................................................................................13
2.3 Electrical connection.....................................................................................................14
2.4 Hydraulic connection .................................................................................................... 14
3 - OPERATION..................................................................................................................... 15
3.1 Getting started..............................................................................................................15
3.2 First start.......................................................................................................................15
3.3 Starting ......................................................................................................................... 15
3.4 Setting...........................................................................................................................15
3.5 Water drain...................................................................................................................15
4 - MAINTENANCE................................................................................................................ 16
4.1 Cleaning the disk .......................................................................................................... 16
4.2 Cleaning the tank..........................................................................................................16
4.3 Changing the pump ...................................................................................................... 16
4.4 Replacing the spinning disk..........................................................................................17
4.5 Changing the float.........................................................................................................18
4.6 Replacing the nozzle ....................................................................................................19
4.7 Accessories .................................................................................................................. 19
5 –TECHNICAL SPECIFICATIONS...................................................................................... 20
5.1 Technical data ..............................................................................................................20
5.2 Wiring diagram..............................................................................................................21
5.3 Spare parts...................................................................................................................22
6 - PROBLEMS AND SOLUTIONS ....................................................................................... 23

FRANCO srl Manual of use and maintenance UCP
3
1 - INTRODUCTION
1.1 General warnings
This device must be used only for the functions it was intended for: "Adiabatic Cooler –Humidifier”. Any other
use has to be considered improper and dangerous. Franco s.r.l. cannot be held liable for any damages caused
by improper, incorrect or unreasonable use, or if the device is used in systems that do not comply with safety
regulations.
- Check the integrity of the device at the opening of the package, paying particular attention to the presence of
damages or deformations of the plastic parts that can lead to breakage and/or malfunction during use. In such
cases do not connect the machine to the main. Carry out these checks before each use.
- Before connecting the unit, make sure that the data shown on the device’s plate matches that of your electricity
distribution network. The data label is located on the side of the device (par.1.9).
- Respect the safety standards set for the electrical equipment and in particular:
oFollow the installation and operation instructions concerning the use of the equipment.
oDo not place objects on the humidifier.
oEnsure that children and/or unable subjects cannot use the device without proper supervision.
oDo not touch the humidifier during operation or until the complete stop of the disk.
oNever immerse the device into water or any other liquid. In case of the device becoming wet,
immediately turn off the electricity by lowering the switch on the electrical panel of your system and
disconnect the power before touching the device.
oDo not insert objects inside the tank as the device may be damaged irreparably.
oDo not use accessories, spare parts and/or components which are not provided or supplied by the
manufacturer.
oAvoid touching the appliance with wet and/or humid hands.
oDo not pull the power cord nor expose it to risk of severing.
oDo not expose the unit to weather (rain, sun, etc...).
oIn case of failure or malfunction, switch off immediately and disconnect the power. Do not try to open or
tamper the device: contact the technical service provided by Franco s.r.l.
oDo not try to fill and/or empty the tank during operation.
1.2 Instructions for proper disposal of the product
Under the European Directive 2002/96/EC.
At the end of its useful life the product must not be disposed of as waste.
The device can be taken to special recycling centers provided by local authorities, or at retailers that provide this
service. Disposing the product in separate parts avoids possible negative consequence to the environment and
to human health, which would both be the result of an inappropriate disposal, and allows the retrieval of
materials which results in significant savings in energy and resources. As a reminder of the obligation to dispose
electrical equipment separately, the product is marked with the crossed mobile waste container.
Fig. 1.1

FRANCO srl Manual of use and maintenance UCP
4
1.3 Conventions used in this manual
The Manual is divided into autonomous chapters, each of which is addressed to a specific operator figures
(installer, operator and maintenance operator), who have the skills needed to operate the machinery safely.
The chapter order follows the temporal logic of the machine life.
To facilitate the immediate understanding of the text, terms, abbreviations and pictograms, whose meaning is
shown below, are used throughout the manual.
The Instruction Manual consists of a cover, an index and a series of chapters (sections).
The home page lists the machine and model identification data, the revision of the instruction manual, and
finally, a picture of the described machine, drawn in order to facilitate the reader to identify the machine and its
use.
ABBREVIAZIONI
Ch. = Chapter
Par. = Paragraph
P. = Page
Fig. = Figure
Tab. = Table
UNITS OF MEASURE
The units of measure used in this manual are those provided by the International System (SI).
1.4 Instruction manual conservation
The instruction manual must be carefully stored and must follow and match the device in all the cases of change
of ownership incurred during the life span of the machine itself.
The manual must be handled with care, with clean hands and placed on clean surfaces. No parts can be
removed, torn or arbitrarily modified.
The manual must be stored in a secure environment, protected from moisture and heat, and near the device to
which it refers. The manufacturer, if requested by the User, may provide additional copies of the machine’s
instruction manual.
The User can request additional copies of the manual by writing to custom[email protected].
UPDATING THE MANUAL
The Manufacturer reserves the right to modify the design or specifications of the machine as part of its policy of
improving and enabling them to comply with the statutory or other requirements or standards applicable in any
territory in which its goods are sold, without notifying the Customer and without updating the manuals given to
the user. Moreover, in case of changes (previously agreed between the Customer and the manufacturer) to the
machine installed, which entails a change in one or more chapters of the Instruction manual, the manufacturer
will be responsible for sending the modified chapters (including the new revision) to the User.
The User is responsible, following the directions accompanying the updated documentation, for replacing all the
copies owned, the old chapters with the new ones, the home page, and the index with the new updated version.
The manufacturer shall be responsible for the descriptions included in this manual; in case of any inconsistency
detected in a translated version of the manual (English version), the reader must refer back to the original Italian
version of the manual and, if needed, contact the sales department, who will make necessary changes.

FRANCO srl Manual of use and maintenance UCP
5
1.5 Recipients
The manual is addressed to: the installer, the operator, and the qualified personnel entitled to the maintenance
of the device.
EXPOSED PERSON:
refers to any person wholly or partially exposed to a danger zone;
OPERATOR:
refers to those persons responsible for installing, operating, regulating,
clearing, repairing and moving the machine, and also performing the
maintenance of the device;
QUALIFIED PERSONNEL
QUALIFIED OPERATOR:
refers to the persons who have completed specialization courses and
training, and who have acquired experience in: installing, starting,
operating, maintaining, repairing and transporting the device, or similar
ones.
The machine is intended for industrial use (professional and not widespread) for which qualified operators are
needed, in particular, workers who:
Have reached the age of majority;
Are physically and mentally appropriate to perform works which include technical difficulties;
Have been properly educated on the use and maintenance of the machinery;
Have been considered suitable to undertake the assigned job by their employer;
Can understand and interpret the operator’s manual and the safety requirements;
Know the emergency procedures and their implementation;
Posses the ability to operate the specific type of equipment;
Are familiar with the specific applicable rules;
Have understood the operating procedures defined by the manufacturer of the machine.
1.6 Glossary and pictograms
In this section we list the uncommon terms included in the manual. The following table also explains the
abbreviations used and the meaning of the pictograms which indicate the qualification of the operator and the
state of the machine; their use can provide quick and unique information, necessary for the proper use of the
machine under safety conditions.
GLOSSARY (Att. I p. 1.1.1 Dir. 2006/42/CE)
HAZARD
A potential source of injury or damage to health;
DANGER ZONE
Any area within and/or around the machinery in which the
presence of a person constitutes a risk to his/her health and
safety;
EXPOSED PERSON
Any person wholly or partially in a danger zone;
OPERATOR
The person installing, operating, adjusting, clearing, repairing,
maintaining and moving the machinery;
RISK
A combination of the probability and degree of an injury or damage
to health that can arise in a hazardous situation;
GUARD
The part of the machinery used specifically to provide protection by
means of a physical barrier;
PROTECTION DEVICE
The device (other than a guard) that reduces the risk of an
operation, either alone or in conjunction with a guard;
INTENDED USE
Use of the machinery according to the information provided in the
instruction manual;
REASONABLY FORESEEABLE
MEASURE
Use of the machinery in a way not intended in the instruction
manual, which may result from a foreseeable human behavior.

FRANCO srl Manual of use and maintenance UCP
6
OTHER DEFINITIONS:
HUMAN-MACHINE INTERACTION: Any situation in which an operator interacts with the machine in any of
the operational phases at any time of the life of the machine itself;
OPERATOR’S QUALIFICATION:Minimum level of competence that an operator must have in order to
perform the described operation;
NUMBER OF OPERATORS: The appropriate number of operators needed to optimally perform the
described operation, resulting from an accurate analysis made by the
manufacture, and for which the use of a different number of operators
may prevent the occurrence of the expected result or endanger the
safety of the personnel involved;
STATE OF THE MACHINE: The state of the machine includes the operating mode, for example:
running in automatic mode, hold-to-run control (jog), shutdown, etc… the
safety conditions on the machine, such as included protectors, excluded
protectors, emergency shutdown, isolation from energy sources, etc…
RESIDUAL RISK: Risks that remain, despite the inherent safe design measures,
safeguarding and complementary protective measures adopted.
SAFETY COMPONENT: Component:
- designed to fulfill a safety function;
- the failure and/or malfunctioning of which endangers the safety of
persons (such as a lifter; a fixed, moving or adjustable protector; an
electrical, electronic, optical, pneumatic or hydraulic device which
interlocks a protector; etc…).

FRANCO srl Manual of use and maintenance UCP
7
PICTOGRAMS REGARDING THE OPERATOR’S QUALIFICATION
Symbol
Description
Generic worker: operator lacking of specific competences, capable of performing only simple tasks
under the control of qualified technicians.
Lifting and handling vehicles driver: operator qualified for the use of vehicles used in lifting and
handling materials and machines (carefully following the manufacturer’s instructions), in accordance
with the user’s country laws.
Mechanical maintenance operator: qualified technician, able to operate the machine under normal
conditions, to run it with the hold-to-run control (JOG) with disabled protections, and to intervene on
the mechanical parts in order to make the necessary adjustments, maintenances and repairs.
Typically this operator is not qualified to work on electrical systems while the device is connected to
the main.
Electrical maintenance operator: qualified technician, able to operate the machine under normal
conditions, to run it with the hold-to-run control (JOG) with disabled protections, and enabled to any
kind of operation of electrical adjustment, maintenance and repair. This operator is qualified to work
on electrical systems while the device is connected to the main.
Manufacturer’s technician: qualified technician provided by the manufacturer to carry out complex or
particular operations or any other operation agreed with the user. The skills are, as the case may be,
mechanical and/or electrical and/or electronic and/or software.
PICTOGRAMS REGARDING THE STATE OF THE DEVICE
Pictograms contained in a square/rectangle provide information.
Symbol
State of the device
Device OFF: with electric and pneumatic power disconnected.
Machine in motion: with automatic function, movable protections closed, relative interlocking
devices activated and fixed protections closed.
Device ON: in standby and ready to start by functional consent activation (eg. switchboard
consent), movable protections closed with relative safety device included, and fixed protections
closed.

FRANCO srl Manual of use and maintenance UCP
8
PICTOGRAMS REGARDING SAFETY
Pictograms in a triangle indicate DANGER.
Pictograms in a circle impose PROHIBITION / OBLIGATION.
Pictogram
Denomination
Hazardous voltage.
Entanglement.
Dragging.
General danger.
Do not remove safety devices.
Prohibition of cleaning, oiling, greasing, repairing or adjusting by hand when the device is in motion.
Obligation to remove power before starting works or repairs.
Protective gloves required.
Safety footwear required.
Safety helmet required.

FRANCO srl Manual of use and maintenance UCP
9
1.7 Applications
In the industrial field, it can be used in Air Treatment Units o in front of a fan (air flow >3m/s). The machine is
installed in places where it is necessary to maintain a certain humidity level, for example in fruits and vegetable
refrigerating rooms, in aging warehouses, in the paper and tobacco industries, and in textile companies.
In agriculture the machine is used to humidify greenhouses and mushroom farms, and for disinfectant
treatments.
In animal husbandry the machine is used to cool or nebulize disinfectants or other solutions in the environment.
The materials used to build the machine ensure reliability and durability in time.
The parts of the humidifier are made of PA PC and ABS, the screws are in stainless steel.
The use of materials that do not suffer from the corrosive action of water and acids makes the UCP a machine
capable of working in almost all the environments.
The UCP combines power of the humidification with easy installation, and, by operating without nozzles, it is not
subject to clogging caused by impurities and limestone.
The water pressure required is the same as in the water supply network (between 2 and 4 atm).
This device must be used only for the functions for which it was intended
and designed: "Adiabatic Cooler –Humidifier”.
Any other use has to be considered improper and dangerous.
1.8 Versions
The adiabatic cooler/humidifier UCP is available in the following versions:
1809001 Version UCP-1 230V 50Hz Single-phase
1809002 Version UCP-1 230V 60Hz Single-phase
1809003 Version UCP-3 400V 50Hz Three-phase + neutral
1809004 Version UCP-3 400V 60Hz Three-phase + neutral
1809012 Version UCP-1 230V 50Hz Single-phase without pump and float valve
1809013 Version UCP-3 400V 50Hz Three-phase without pump and float valve
1.9 Identification and data label of the unit
Each machine is identified by the CE plate on which the reference data of the device is inscribed indelibly.
In any communication, either with the manufacturer or with the customer service, always cite these references.
Fig.1.2
The label plate positioning may vary from one device to another.

FRANCO srl Manual of use and maintenance UCP
10
Spinning disk
Spinning disk cap
Tank lid
Rear shelter
Float valve
Recirculation pump
Nozzle
Electric motor
Water supplì
connection ½”
Water flow regulation
valve
Fast connection drain
hole ⅜” with cap.
Fixed disk
1.10 Parts description
Constituent parts of the centrifugal atomizer
fig.1.3
1.11 Transport and handling
The machine has been properly packed before being put into sturdy carton boxes.
Carefully open the package to prevent damages to the components of the device.
Verify the integrity of the machine by controlling that there are no visible damaged parts.
Do not dispose the packaging elements in the environment; they must be disposed in suitable waste
collection points.
The UCP can be lifted and hung using suitable brackets. L’APPOGGIO ALLA BASE DEL MOTORE
WARNING!
Before moving the device:
a. stop the machine,
b. disconnect the electrical supply,
c. interrupt the water supply.
To lift the machine, use a suitable lifting device (consult the weights table).
Lift the machine slowly, being careful not to drop it and moving the straps according to the centre of mass.