FRC TACH P3 TPA600 User manual

TPA600 Rev170623
1
ENGINE MONITORING DISPLAY
MODEL: TPA600
Document Number:
XE-TPA6PM-R0A
FIRE RESEARCH CORPORATION
www.reresearch.com
26 Southern Blvd., Nesconset, NY 11767
TEL [phone] FAX [phone] TOLL FREE 1.800.645.0074

TPA600 Rev170623
2
CONTENTS
Table of Contents
CONTENTS................................................................................................................ 2
INTRODUCTION ...................................................................................................... 3
Overview................................................................................................................ 3
Features.................................................................................................................. 3
Specications......................................................................................................... 3
GENERAL DESCRIPTION ....................................................................................... 4
Components ........................................................................................................... 4
Controls and Indicators.......................................................................................... 4
INSTALLATION ........................................................................................................ 6
Install Display Module........................................................................................... 6
Install Buzzer ........................................................................................................ 6
OPERATION .............................................................................................................. 8
Transmission Temperature..................................................................................... 8
Engine Hours ......................................................................................................... 8
PROGRAMMING .................................................................................................... 10
Program Access.................................................................................................... 10
WIRING.................................................................................................................... 12
Connectors and Cables......................................................................................... 12
List of Tables and Figures
Table 1. Error and Fault Warning Codes.................................................................... 9
Table 2. Program Functions ..................................................................................... 11
Figure 1. Controls and Indicators............................................................................... 5
Figure 2. Display Module Mounting Dimensions ..................................................... 7
Figure 3. Wiring ....................................................................................................... 12

TPA600 Rev170623
3
INTRODUCTION
Overview
The Engine Monitoring Display is an all-in-one instrument panel with integrated
monitoring and display capabilities that saves valuable pump panel space. It combines
four different instruments in one waterproof unit. It provides both audible and visual
warning alarms if specied parameters go outside of set limits.
The Engine Monitoring Display has a 4-digit LED display for engine RPM and
3-digit LED displays for engine oil pressure, engine coolant temperature, and battery
voltage. During normal operation warning messages are displayed as they occur.
The Engine Monitoring Display receives input information form the J1939 CAN
bus.
Features
Non-Multiplexed Display Means No Flickering
Digital Engine RPM, Oil Pressure, and Coolant Temperature Displays
Battery Voltage Display with Low and Over Voltage Warnings
Automatically Adjusts to 12 or 24 Volt System
Programmable Parameters
Audible and Visual Warnings
LED Brightness Automatically Adjusts for Day or Night Operation
Transmission Temperature Displayed (When Available)
Specications
Display Module
Supply Power: 12/24 VDC/ Auto Detected
Supply Current: 1.5 Amps
Dimensions: 4.2" by 4.2" by 0.7"
Audible Alarm Buzzer
Volume: 95 dB

TPA600 Rev170623
4
GENERAL DESCRIPTION
The Engine Monitoring Display receives all input from the J1939 CAN bus.
Components
The Engine Monitoring Display consist of the following components:
Display Module
Buzzer
Controls and Indicators
All controls and indicators are located on the front of the control module. Refer
top Operation and Programming Sections for more information.
RPM Display
Shows the current engine RPM in bright red digits. It also shows error codes, stored
data, and program features.
OIL PRESSURE Display
Shows the engine oil pressure in bright red 0.4" digits.
ENGINE TEMP Display
Shows engine coolant temperature in bright red 0.4" digits. (Shows transmission
temperature when selected.)
VOLTAGE Display
Shows the battery voltage in bright red 0.4" digits.
When in the information scroll mode this display shows system and options information.
MENU Button
The MENU button is used to show the transmission temperature if it is available.
It is also used to access program features. (Transmission temperature is shown in the
ENGINE TEMP display.)
SILENCE Button
The SILENCE button is to de-activate the audible warning alarm. It is also used
to access program features.

TPA600 Rev170623
5
Figure 1. Controls and Indicators
RPM
Display
ENGINE TEMP
Display
VOLTAGE
Display
MENU
Button
SILENCE
Button
OIL PRESSURE
Display

TPA600 Rev170623
6
INSTALLATION
The Engine Monitoring Display receives engine RPM, oil pressure, coolant
temperature, and voltage information over the J1939 CAN bus from the engine ECM.
(Refer to Wiring Section.)
Install Display Module
1. Measure and mark mounting location for display module cable and mounting
screw holes. Make sure there is clearance behind the panel for the module and
cables before drilling holes. Refer to Figure 2 for layout and dimensions.
2. Drill a 1.25-inch diameter hole.
3. Drill four holes, clearance or tapped, for 10-32 mounting screws.
3. Place display module in position and secure with screws.
4. Connect cable at rear of the module. (Refer to Wiring section.)
Install Buzzer
A buzzer is supplied with the Engine Monitoring Display. Install the buzzer close to
the control module so the audible warning is easily associated with the visual warning
on the display. A cutout hole of 1-1/8" (1.125") is required on the pump panel. (Refer
to Wiring Section.)

TPA600 Rev170623
7
Figure 2. Display Module Mounting Dimensions
0.7"
4.2"
2.0"
4.2"
1.25"
Diameter Hole Mounting holes are
clearance or tapped
for 10-32 screws.
3.5"
3.5"

TPA600 Rev170623
8
OPERATION
The Engine Monitoring Display shows crucial engine information to the pump operator.
Visual Alarm
When a monitored input exceeds the set warning level the display ashes. This
visual alarm cannot be reset or cancelled manually. The alarm stops automatically
when the monitored input is at a normal level.
Audible Alarm
The audible alarm is a clear distinctive warning that sounds when a monitored
input exceeds the set warning level.
Silencing Audible Alarm
All audible alarms can be cancelled by pressing the SILENCE button. Pressing
the SILENCE button does not change the visual warning.
Transmission Temperature
When the transmission temperature is available on the J1939 CAN bus and the
program code P07 is enabled, press the MENU button to show it on the ENGINE
TEMP display.
Engine Hours
To access the Engine Hours feature, press the MENU button again and Eng Hr is
shown on the display. The actual number of hours will be shown on the RPM display.

TPA600 Rev170623
9
Table 1. Error and Fault Warning Codes
DISPLAY DESCRIPTION
E01 No Engine Data Received
E04 Oil Pressure Problem
E07 Engine Temp Problem
F01 High Battery Voltage
F02 Low Battery Voltage
F03 High Transmission Temperature
F04 Low Oil Pressure
F07 High Engine Coolant Temperature

TPA600 Rev170623
10
PROGRAMMING
To access the program functions, to view and change parameter settings, a password
is entered. The code for the Engine Monitoring Display is 2222.
Note: To exit the programming mode press the SILENCE and MENU buttons
together. (The program mode times out after ten seconds if no buttons
are pressed.)
Program Access
1. Press the SILENCE button and hold it until the RPM display shows four
dashes – – – – . Release the button.
2. Press the MENU button within three seconds. The RPM display shows
the number 1000. Each time the MENU button is pressed the rst digit
increments by 1. Set the rst digit to the desired number.
3. Press the SILENCE button to move the curser to the next digit. Press the
MENU button to change the digit.
4. Repeat step 3 and enter the password code 2222.
Result: When a correct password code is entered P 0 1 shows in the
RPM display.
5. Press the SILENCE button to scroll through the program (P) codes.
6. Press and hold the MENU button for three seconds to enter the
programming mode to view and change parameter settings.
7. While the parameter or value is ashing, press and hold the MENU button
to change a selectable parameter or numerical value. Press the MENU
button again to change the digit, or scroll through values. Next press the
SILENCE button to move the cursor to the next digit to be changed, or the
next window option.
8. Repeat steps 5 through 7 as necessary.
9. To exit the programming mode, press the SILENCE button to scroll through
the P-codes until P99 is reached. At P99, the display will read 'END'. Press
and hold the MENU button to fully exit the Programming mode and return
to normal operation.