Frigidaire GLMB186K User manual

PART QUANTITY
Trim Frame 1
Bottom Duct 1
Side Duct 1
1” Screws 6
(4 required, 2 extra)
1⁄2” Screws 15
(11 required, 4 extra)
Anti-Tip Bracket 1
Bottom Bracket 1
Upper Duct 1
Template 1
Questions? In the U.S., call 1-800-944-9044. In Canada, call 1-866-213-9397 (English),
1-800-669-4606 ext. 8199 (French). Visit our Website at: www.frigidaire.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions
82-1827 and 82-1830
Phillips screwdriver
Pencil
Tape measure
Awl or punch
Drill with 7⁄64″bit or #35
1
164D3370P160
49-40169-1
P/N 316137209 Rev. A
Printed in Korea (05-01 JR)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT –Save these
instructions for local inspector’s use.
•IMPORTANT –Observe all
governing codes and ordinances.
•Note to Installer –Be sure to leave these
instructions with the Consumer.
•Note to Consumer –Keep these
instructions for future reference.
• Unplug the microwave oven before attempting
installation of this kit.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• This kit is UL and CUL listed for installation alone or
over any Frigidaire single electric wall oven.
FOR YOUR SAFETY:
WARNING –Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
TOOLS YOU WILL NEED
PARTS INCLUDED

2
Installation Instructions
CUTOUT DIMENSIONS
On 27″(68.6 cm) models, allow 1″(2.5 cm) at the top,
11⁄16″(1.75 cm)on the sides and 13⁄8″(3.5 cm)at the
bottom for overlap of the Trim Frame over the edges
of the cutout.
On 30″(76.2 cm) models, allow 1″(2.5 cm) at the top,
23⁄16″(5.6 cm) on the sides and 13⁄8″(3.5 cm) at the
bottom for overlap of the Trim Frame over the edges
of the cutout.
1.
* Min. depth with receptacle outside cabinet 191⁄2″ (49.5 cm).
Min. depth with receptacle inside cabinet 22″ (56 cm).
Depth
Height
3″Min.
(7.6 cm)
Width
Models 27″30″
(68.6 cm) (76.2 cm)
Height 163⁄4″163⁄4″
(42.5 cm) (42.5 cm)
Width 251⁄2″251⁄2″
(6.5 cm) (6.5 cm)
Depth (min.)* 191⁄2″or 22″191⁄2″or 22″
(49.5 cm or (49.5 cm or
56 cm) 56 cm)
INSTALL BOTTOM BRACKET
AND BOTTOM DUCT
Disconnect the microwave oven before proceeding
with the installation.
Fasten the bottom bracket to the bottom duct by
using two 1⁄2″screws.
Remove any loose items inside the microwave oven,
including the turntable and turntable support.
Carefully turn the microwave upside down.
Install bottom duct with four 1⁄2″screws as shown.
Microwave Oven Upside Down
D
C
B
A
2.
Front
Rear
1⁄2″Screws (2)
Screws
Screws

3
Installation Instructions
INSTALL THE ANTI-TIP BRACKET
Fold or cut the front edge of the template, along the
front guide line. Place the template flush along the
front edge of the cutout floor, aligning the center
line of the template with the center line of the
cutout floor. Mark the center positions with an awl
or center punch for the anti-tip bracket location
as shown.
Remove the template and drill two holes for the
anti-tip bracket.
Install the anti-tip bracket onto the cutout floor
using two 1⁄2″screws.
C
B
A
3.
Cutout Floor
1⁄2″Screws (2)
Anti-Tip Bracket
INSTALL SIDE DUCT AND
UPPER DUCT
Connect the side duct to the upper duct as shown.
1. Insert projecting tabs of the upper duct into the
holes of the side duct.
2. Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the
microwave oven before the ducts are attached.
Set the microwave upright, being careful not to
bend the front flange. Remove the one existing
screw from the left side of the microwave oven.
Peel off the backing of the double sided tape.
Carefully position the side duct and upper duct
assembly on the microwave cabinet, aligning with
the bottom screw hole. Press down firmly on the
ducts. Fasten the duct assembly to the left side of
the cabinet with the screw removed above.
C
B
A
4.
(2)
(1)
Existing Screw (1)
Upper Duct
Side Duct
3 Tabs
3 Holes

INSTALLING THE TRIM FRAME
Place the trim frame over the microwave oven.
Make sure the trim frame is level and the microwave
oven is centered within the trim frame. Mark four
center positions through the four mounting holes
of the trim frame.
NOTE: Center the trim frame equally on all four
sides.
Remove the trim frame and drill four pilot holes.
Attach the trim frame by using four screws.
D
C
B
A
6.
4
Installation Instructions
Pilot Hole
Cutout Opening
Mounting Hole
Trim Frame
1″Screw
INSTALL MICROWAVE OVEN
INTO CABINET
Slide the microwave oven part way into the cabinet
opening.
Plug in the microwave oven.
Bottom bracket must be flat to the cutout floor to
engage correctly with the anti-tip bracket as shown.
Carefully slide the microwave back, making sure the
power cord is not mashed or cut.
Center the microwave oven within the cutout
opening and slide the microwave oven in place,
engaging the anti-tip bracket.
Ensure the microwave oven is accurately centered.
Drill pilot holes through the positioning flange and
then install three 1⁄2″screws at the front of the
bottom duct as shown.
F
E
D
C
B
A
5.
Anti-Tip Assembly
Bottom Duct
1⁄2″Screw
Bottom Bracket
Anti-Tip
Bracket
Cutout Opening
Positioning Flange
1⁄2″Screw
REPLACE ANY LOOSE ITEMS
Your trim kit is now fully installed. Replace any
loose items that were removed from the inside of
the microwave oven.
Keep these installation instructions for future
reference.
Replace house fuse or close circuit breaker.
C
B
A
7.