Frigidaire Designer Series User manual

Dual Fuel
Range
Slide-in Models
P/N 318200804 (9903) Rev. B
Owner’s
Guide
CONTENTS
Warranty ......................................Page 2
GENERALINFORMATION ............. 318200342
Avoid Service Checklist........ 318130502
Professional
series
and

© 1999 White Consolidated Industries
All rights reserved
WARRANTY APPLIES TO:
a) Products purchased and installed in Canada for personal single family household use.
b) Defects resulting or arising out of the manufacturing process.
c) Products bearing legible manufacturer’s model and serial numbers.
d) Replacement parts only for the remainder of the original warranty.
WARRANTY DOES NOT APPLY TO:
a) Transportation damage.
b) Supply and replacement of porcelain, glass and light bulbs.
c) Parts and service supplied or obtained from other than FRIGIDAIRE HOME PRODUCTS – PARTS AND SERVICE or FRIGIDAIRE HOME
PRODUCTS – PARTS AND SERVICE authorized depots.
d) Damage or failure as the result of the abuse, improper or commercial use.
CONSUMER/OWNER RESPONSIBILITY:
a) To provide proof of the original date of purchase by means of a bill of sale verifying purchase date.
b) To pay all costs to make the appliance readily accessible for service.
c) To ensure proper power supply and connection of the appliance to the same.
d) Proper installation, control setting and care of finish.
This warranty is in addition to any statutory warranties contained in any applicable legislation. The terms and condition of this warranty are
not intended to exclude or limit your rights under those statutes. The warrantor however reserves the right to charge transportation and
travelling costs for distances in excess of 48 kilometers (30 miles) from the nearest FRIGIDAIRE HOME PRODUCTS – PARTS AND SERVICE
authorized service depot.
This warranty plus the statutory warranties mentioned are the only warranties given to the consumer/owner for this product.
WARRANTY
DUAL FUEL RANGE
WARRANTOR:
Frigidaire Home Products
7075 Ordan Drive
Mississauga, Ontario
L5T 1K6
This range is a brand product of Frigidaire Home
Products.
WARRANTY PERIOD
For the first and second year after purchase by the
original owner.
For third, fourth and fifth year after purchase by
the original owner.
For third through tenth year after purchase by the
original owner.
For service under this warranty, contact your local dealer/retailer, authorized
FRIGIDAIRE HOME PRODUCTS - PARTS AND SERVICE depot, or:
FRIGIDAIRE HOME PRODUCTS - PARTS AND SERVICE
7075 Ordan Drive
Mississauga, Ontario, L5T 1K6
Tel.: [phone]
Fax.: [phone]
WARRANTOR WILL, THROUGH ITS AUTHORIZED SERVICE DEPOT:
Pay all costs to repair or replace defective parts.
Pay all costs (excluding service and labour charge) to repair or replace defective oven
heating elements.
Pay all costs (excluding service and labour charge) to repair or replace defective
cooktop burners.
TO REDUCE RISK
OF TIPPING OF THE RANGE, THE
RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP
BRACKET(S) PROVIDED WITH
THE RANGE. TO CHECK IF THE
BRACKET(S) IS (ARE) INSTALLED
PROPERLY, REMOVE THE
DRAWER AND VERIFY THAT THE
ANTI-TIP BRACKET(S) IS (ARE)
ENGAGED. REFER TO THE
INSTALLATION INSTRUCTIONS
FOR PROPER ANTI-TIP
BRACKET(S) INSTALLATION.
• ALL RANGE
CAN TIP.
• INJURY TO
PERSONS
COULD
RESULT.
• INSTALL
ANTI-TIP
DEVICE
PACKED
WITH
RANGE.
• SEE
INSTALLATION
INSTRUCTIONS.
FOR YOUR SAFETY:
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas
supplier, call the fire department.
- Installation and service must be
performed by a qualified installer,
servicer or gas supplier.
If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury or death.

General 1 information
318200342 (9903) Rev. B
RecyclablePaper
PRINTED IN CANADA
○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○
○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○○○○○○○
Page
IMPORTANT SAFETY INSTRUCTIONS ....................... 2-4
SELECTING SURFACE COOKING UTENSILS.................. 4
LIQUEFIED PETROLEUM
(PROPANE) GAS CONVERSION ................................... 5
FLAME SIZE ................................................................ 5
SETTING SURFACE CONTROLS ................................... 6
BEFORE SETTING OVEN CONTROLS............................ 6
SETTING OVEN CONTROLS......................................... 6
BEFORE SETTING WARMER DRAWER CONTROL......... 7
SETTING WARMER DRAWER CONTROL .................. 7-8
CONVECTION COOKING............................................ 8
CONVECTION ROASTING........................................... 8
OVEN BAKING............................................................ 9
AIR CIRCULATION IN THE OVEN ................................. 9
BROILING................................................................. 10
CHANGING OVEN LIGHT.......................................... 10
GENERAL CLEANING
Cleaning Various Parts of Your Range ................... 11
To Clean the Cooktop Glass.................................. 12
To Clean the Burner Grates, Contoured
Burner Pans, Burner Cap and Burner Base ........ 12-13
Cleaning the Self-Clean Oven .......................... 13-14
Setting Controls for Clean Cycle............................ 14
To Remove and Replace Oven Door....................... 14
Removable Outer Door Glass Panel ....................... 15
To Remove and Replace Warmer Drawer ............... 15
Storage Drawer ..................................................... 15
NOTES...................................................................... 16
Thank you for choosing this appliance. The information contained within this
Owner's Guide will instruct you on how to properly operate and care for your appli-
ance. Please read through the information contained in your literature pack to learn
more about your new appliance.
This owner's Guide contains general operating instructions for your appliance and feature information for several models. Your appli-
ance may not have all the described features.
Note: The instructions appearing in this Owner's Guide are not meant to cover every possible condition and situation that may occur.
Common sense and caution must be practiced when installing, operating and maintaining any appliance.
PLEASE DO THIS NOW!
The PRODUCT REGISTRATION
CARD should be filled in completely,
signed, and returned. This
information will register your
product and help us to serve you
quickly in the future if the occasion
should demand.
IMPORTANT
Keep a copy of your bill of sale.
The date on the bill establishes the
warranty period should service be
required. Place it where it can be easily
retrieved. If service is performed, while
the appliance is under warranty you
may have to show your bill of sale.
Record the model and serial numbers of this appliance in the space provided
below. These numbers are shown on the serial plate located at the left of
the range frame and are visible when the oven door is open or on the inside
of the drawer along the side of the frame.
Model No.:
Serial No.:
Date Purchased:
Record these numbers for future reference.
SOME MODELS
General
Information

General 2 information
• Remove all tape and packaging wrap before using the
appliance. Destroy the carton and plastic bags after
unpacking the appliance. Never allow children to play with
packaging material.
• Proper Installation—Be sure your appliance is properly
installedandgroundedbyaqualifiedtechnicianinaccordance
with Canadian Standards CAN/CGA B149.1, and CAN/CGA
B149.2 and Canadian Electrical Code, part 1, and local
requirements. Install only per installation instructions provided
in the literature package for this appliance.
Ask your dealer to recommend a qualified technician and an
authorized repair service. Know how to disconnect the electrical
power to the appliance at the circuit breaker or fuse box and gas
supply at the main shutoff valve in case of an emergency. Remove
the drawer to access the valve.
• User Servicing—Do not repair or replace any part of the
applianceunlessspecificallyrecommendedinthemanuals.All
other servicing should be done only by a qualified technician to
reduce the risk of personal injury and damage to the appliance.
• Never modify or alter the construction of an appliance by
removinglevelinglegs,panels,wirecovers,anti-tipbrackets/
screws, or any other part of the product.
Stepping, leaning or sitting on the door or
drawer of this appliance can result in serious injuries and may
alsocausedamagetotheappliance.Donotallowchildrentoclimb
or play around the appliance. The weight of a child on an open door
may cause the appliance to tip, resulting in serious burns or other
injury. An open drawer, when hot, may cause burns.
Do not use the oven or warmer drawer (if
equipped) for storage.
• StorageinoronAppliance—Flammablematerialsshouldnot
be stored in an oven, near surface burners or in the drawer
(ifequipped). Thisincludespaper,plasticandclothitems,suchas
cookbooks, plasticware and towels, as well as flammable liquids.
Do not store explosives, such as aerosol cans, on or near the
appliance. Flammable materials may explode and result in fire or
property damage.
Do not store items of interest to children in the
cabinets above the appliance.
• Donotleavechildrenalone.Childrenshouldnotbeleftalone
or unattended in the area where an appliance is in use. They
shouldneverbeallowedtositorstandonanypartoftheappliance.
This guide contains important safety symbols and instructions. Please pay special attention to these symbols and follow all instructions
given. Here is a brief explanation of the use of these symbols.
This symbol will help alert you to situations that may cause serious bodily harm, death or property damage.
This symbol will help alert you to situations that may cause bodily injury or property damage.
• DO NOT TOUCH SURFACE BURNERS, GRATES, AREAS NEAR
THESE BURNERS, OVEN HEATING ELEMENTS OR INTERIOR
SURFACESOFTHEOVENORWARMERDRAWER(ifequipped).
Both surface burners and oven heating elements may be hot even
though they are dark in color. Areas near surface burners may
become hot enough to cause burns. During and after use, do not
touch, or let clothing or other flammable materials touch these
areasuntiltheyhavehadsufficienttimetocool.Amongtheseareas
are the cooktop, surfaces facing the cooktop, the oven vent
openings and surfaces near these openings, oven door and
window.
• Wear Proper Apparel—Loose-fitting or hanging garments
should never be worn while using the appliance. Do not let
clothing or other flammable materials contact hot surfaces.
Never use your appliance for warming or
heating the room.
• DoNot UseWateror FlouronGrease Fires—Smotherthefire
withapanlid,orusebakingsoda,adrychemicalorfoam-type
extinguisher.
• Whenheatingfatorgrease,watchitclosely.Fatorgreasemay
catch fire if allowed to become too hot.
Incaseof fireor gasleak, besure toturn offthe
main gas shutoff valve.
• Use Only Dry Potholders—Moistordamppotholderson hot
surfaces may result in burns from steam. Do not let the
potholders touch the flame, burners or interior oven elements. Do
not use a towel or other bulky cloth instead of a potholder.
• DoNotHeatUnopenedFoodContainers—Buildupofpressure
may cause the container to burst and result in injury.
• Removetheovendoorfromanyunusedapplianceifitistobe
storedor discarded.
• IMPORTANT—Do not attempt to operate the oven during a
power failure. If the power fails, always turn the oven off. If
the oven is not turned off and the power resumes, the oven may
begin to operate again. Food left unattended could catch fire or
spoil.
Use Proper Flame Size—Adjust flame size so it
does not extend beyond the edge of the utensil. The use of
undersized utensils will exposed a portion of the burner flame to
direct contact and may result in ignition of clothing. Proper
relationship of utensil to flame will also improve efficiency.
Read all instructions before using this appliance.
Save these instructions for future reference.
IMPORTANT SAFETY INSTRUCTIONS

General 3 information
IMPORTANT SAFETY INSTRUCTIONS (continued)
Donotusestovetopgrillsontheburnergrates
ofyoursealed gasburners.Ifyouuseastovetopgrillonasealed
gas burner, it will cause incomplete combustion and can result in
exposure to carbon monoxide levels above allowable current
standards. This can be hazardous to your health.
Electroniccontrollerscanbedamagedbycold
temperatures.Whenyouuseyourapplianceforthefirsttime,
orifithasnot beenused fora longperiod oftime, makesure
thatithasbeenexposedtoatemperatureabove0°C/32°Ffor
at least 3 hours before connecting it to the power supply.
IMPORTANT INSTRUCTIONS FOR USING YOUR
COOKTOP
• Knowwhichknobcontrolseachsurfaceheatingunit.Always
turn the knob to the LITE position when igniting the burners.
Visually check that the burner has lit. Then adjust the flame so
it does not extend beyond the edge of the utensil.
• Use Proper Pan Size—This appliance is equipped with one or
moresurfaceburnersofdifferentsizes.Selectutensilshavingflat
bottoms large enough to cover the surface burner. The use of
undersized utensils will expose a portion of the surface burner
to direct contact and may result in ignition of clothing. Proper
relationship of utensil to the surface burner will also improve
efficiency.
• Utensil Handles Should Be Turned Inward and Should Not
ExtendOverAdjacentSurfaceBurners—Toreducetheriskof
burns, ignition of flammable materials, and spillage due to
unintentional contact with the utensil. The handle of the utensil
should be positioned so that it is turned inward, and does not
extend over adjacent surface burner.
• Never Leave Surface Burners Unattended—Boilovers cause
smoking and greasy spillovers that may ignite, or a pan that has
boiled dry may melt.
• Protective liners— Do not use aluminum foil to line oven
bottom or any other part of the appliance. Only use aluminum
foil as recommended for baking if used as a cover placed on the
food. Any other used of protective liners or aluminum foil may
result in a risk of electric shock or fire or a short circuit.
• Glazed Cooking Utensils—Only certain types of glass, glass/
ceramic, ceramic, earthenware, or other glazed utensils are
suitable for rangetop service without breaking due to the
sudden change in temperature. Check the manufacturer's
recommendations for rangetop use.
• Do Not Use Decorative Surface Burner Covers. If a burner is
accidentallyturnedon,thedecorativecoverwillbecomehot and
possibly melt. Burns will occur if the hot covers are touched.
Damagemayalsobedonetothecooktoporburnersbecausethe
covers may cause overheating. Air will be blocked from the
burner and cause combustion problems.
IMPORTANT INSTRUCTIONS FOR USING YOUR
OVEN
• Use Care When Opening Door or Warmer Drawer (if
equipped)—Stand to the side of the appliance when opening the
door of a hot oven. Let hot air or steam escape before you remove
or replace food in the oven/warmer drawer.
• Keep Oven Vent Ducts Unobstructed. The oven isventedat the
rear of the cooktop. Touching the surfaces in this area when the
ovenisoperatingmaycausesevereburns.Also,donotplaceplastic
orheat-sensitive items on or near the ovenvent. These items could
melt or ignite.
• Placement of Oven/Warmer Drawer (if equipped) Racks.
Always place oven racks in desired location while oven/drawer (if
equipped) is cool. Remove all utensils from the rack before
removingrack.Ifrackmustbemovedwhileovenishot,useextreme
caution. Use potholders and grasp the rack with both hands to
reposition. Do not let potholders contact the hot oven element or
interior of the oven/warmer drawer (if equipped).
• Donotusethebroilerpanwithoutitsinsert.Thebroilerpanand
gridallowdrippingfattodrainandbekeptawayfromthehighheat
of the broiler.
• Donot coverthebroiler orwarmer drawer (ifequipped) grid
with aluminum foil. Exposed fat and grease could ignite.
• Donottouchahotlightbulbwithadampcloth.Doingsocould
cause the bulb to break. Disconnect the appliance or turn off the
power to the appliance before removing and replacing light bulb.
IMPORTANT INSTRUCTIONS FOR CLEANING YOUR
RANGE
• Clean the appliance regularly to keep all parts free of grease
that could catch fire. Exhaust fan ventilation hoods and grease
filters should be kept clean. Do not allow grease to accumulate.
Greasy deposits in the fan could catch fire. Refer to the hood
manufacturer's instructions for cleaning.
• Cleaners/aerosols—Always follow the manufacturer's
recommendeddirectionsforuse.Beawarethatexcessresiduefrom
cleaners and aerosols may ignite causing damage and/or injury.

General 4 information
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS(continued)
Selecting Burner Cooking Utensils
For best result and energy conservation, choose cooking utensils that have these characteristic:
Pansshould have flat bottoms.Checkfor
flatnessby rotatingaruleracross thebot-
tom. There should be no gap between
the pan and ruler.
Note:Always use a utensil for its intend-
ed purpose. Follow manufacturer's in-
structions.Someutensilswerenotmade
tobe used intheoven or onthecooktop.
*Specialty pans such as lobster pots, griddles and pressure cookers may be used
butmust conform to theaboverecommended cookware requirements.
SELF-CLEANING OVENS:
• Cleanintheself-cleaningcycleonlythepartsoftheovenlisted
in this owner's guide. Beforeself-cleaningtheoven,removethe
broiler pan and any utensils stored in the oven.
• Donot clean theoven door gasket.Thedoorgasketisessential
fora good seal. Careshould be takennotto rub, damageor move
the gasket.
• Donotuseovencleaners.Noovencleanerorovenlinerprotective
coatingofanykindshouldbeusedinoraroundanypartoftheoven.
• Removeovenracks.Ovenrackscolorwillchangeifleftintheoven
during a self-cleaning cycle.
Note: Do not use griddle on more than
one burner. That can damage your
cooktop and that can result in exposure
to carbon monoxide levels above allow-
ablecurrentstandards.That can hazard-
ous to your health.

General 5 information
Conversion Petroleum (Propane) Gas Conversion
The cooktop can be used with Natural Gas or Propane Gas. It is shipped from the factory for use with natural gas.
If you wish to convert your appliance for use with LP/Propane gas, use the supplied fixed orifices located in a bag containing the literature
marked, "FOR LP/PROPANE GAS CONVERSION". Follow the instructions package with the orifices.
The conversion must be performed by a qualified service technician in accordance with the manufacturer's instructions and all codes and
requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The
qualified agency performing this work assumes responsibility for the conversion.
Severe shock or damage to the appliance may occur if the appliance is not installed by a qualified installer.
Flame Size
For most cooking, start on the highest control setting and then turn to a lower one to complete the process.
Use a chart below as a guide for determining proper flame size for various types of cooking. The size and type
of utensil used and the amount of food being cooked will influence the setting needed for cooking.
For deep fat frying, use a thermometer and adjust the surface control knob accordingly. If the fat is too cool,
the food will absorb the fat and be greasy. If the fat is too hot, the food will brown so quickly that the center
will be undercooked. Do not attempt to deep fat fry too much food at once as the food will neither brown or
cook properly.
* These settings are based on using medium thickness aluminum pans with lids. Settings may vary
when using other types of pans.
Type of Cooking
Start most foods; bring water to a boil; pan broiling
Maintain a slow boil; thicken sauces, gravies; steam
Keep foods cooking; poach; stew
*Flame Size
High Flame
Medium Flame
Low Flame
Never extend the flame
beyondtheouteredgeof
the utensil. A higher
flame simply wastes heat
andenergy,andincreases
yourrisk of being burned
by the flame.
RIGHT
WRONG

General 6 information
Setting Surface Controls
The color of the flame is the key to proper burner adjustment. A good flame is clear, blue and hardly visible in a well-lighted room. Each
cone of flame should be steady and sharply defined. Adjust or clean burner if flame is yellow-orange. To clean burner, see instructions
under General Cleaning.
Each burner lights automatically from an electric ignitor each
time a control knob is turned to the LITE position.
To operate the surface burner:
1. Place cooking utensil on burner.
2. Push in and turn the Surface Control knob counterclockwise to LITE.
3. Visually check that the burner has lit.
4. After the burner ignites, turn the control knob to the desired flame size. The knob can now be turned in
either direction without being pushed in. The control knobs do not have to be set at a particular mark.
Use the guides and adjust the flame as needed. DO NOT cook with the control knob in the LITE
position, as this will cause excess wear on the ignitor electrode.
5. To turn the burner off, turn the control knob clockwise as far as it will go, to the OFF position.
In the event of an electrical power outage, the surface burners can be lit manually. To light a surface burner, hold a lit match to the
burner head, then slowly turn the surface control knob to LITE. After the burner ignites, turn the control knob to the desired flame size.
Use caution when lighting surface burners manually.
Surface burners in use when an electrical power failure occurs will continue to operate normally.
Do not operate the burner for an extended period of time without cookware on the grate. The finish on the
grate may chip without cookware to absorb the heat.
Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top of the
cooktop when it is in use. These items could melt or ignite. Pot holders, towels or wood spoons could catch fire if placed too close to a
flame.
Before Setting Oven Controls
Oven Vent Location
The oven is vented through at the rear of the cooktop. When the oven is on, warm air is
released through the vents. This venting is necessary for proper air circulation in the oven
andgood baking results. DO NOT block the vents. Doing so may cause cooking failures, fire
or damage to the appliance
Arranging Oven Racks
ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL (PRIOR TO OPERATING THE
OVEN). Always use oven mitts when using the oven.
To remove an oven rack, pull the rack forward until it stops. Lift up front of rack and slide
out.
To replace an oven rack, Fit the rack onto the guides on the oven walls. Tilt the front of
the rack upward and slide the rack back into place.
Setting Oven Controls
For oven settings, refer to the time or the electronic oven control section.
NOTE: All knobs shown in this
owner's Guide are typical only .
Surface Burner Control
Knob

General 7 information
Before Setting Warmer Drawer Control (some models)
ArrangingWarmer DrawerRackPositions
Set the warmer drawer rack in the vertical position as shown beside:
The rack can be used in 2 ways:
• In the upright position to allow low profile food items to be
placed both under and on top of the rack (for example, rolls or
biscuits on top of the rack and a casserole dish under).
• In the Downward position to allow you to place light weight
food items and empty dishware (for example, rolls or pastries and
dinner plates)
Setting Warmer Drawer Control(some models)
Note: The warmer drawer cannot be used during an oven self-cleaning cycle. The warmer drawer is equipped with a catch which may
require extra force when opening and closing the drawer.
To Operate the Warmer Drawer
The purpose of the warmer drawer is to keep hot cooked foods at serving temperature. Always start with hot food. It is not recommended
to heat cold food in the warmer drawer.
All food placed in the warmer drawer should be covered with a lid or aluminum foil to maintain moisture and softness. Do not cover crisp
foods. Do not use plastic wrap to cover food. Plastic may melt onto the drawer and be very difficult to clean.
Use only dishware, utensils and cookware recommended for oven use in the warmer drawer.
Always use pot holders or oven mitts when removing food from the warmer drawer as cookware and plates will be hot.
Indicator Light
The indicator light is located above or below the thermostat control knob. It turns on when the control is set, and stays on until the control
is turned off. Make sure indicator light is off when removing food from drawer.
To Set the Thermostat Control
The thermostat control knob is used to select the temperature of the warmer drawer. It is located on the
control panel. The temperatures are approximate, and are designated by HI, MED and LO. The control can be
set to the three settings, or anywhere between.
1. To set the thermostat, push in and turn the knob to the desired setting.
2. For best results, preheat the drawer before adding food. An empty drawer will reach the LO setting in
about 12 minutes, the MED setting in about 15 minutes, and the HI setting in about 18 minutes.
3. When done, turn the thermostat control to OFF.
UprightPosition Downward Position
Use the warmer drawer to keep hot foods hot such as: vegetables, gravies, meats, casseroles, biscuits and rolls, pastries and heated
dinner plates.
WARM & SERVE
DRAWER

General 8 information
ROASTING
GRID
BROILER
Setting Warmer Drawer Controls(some models) (continued)
Temperature Selection
Refer to the chart for recommended settings. If a particular food is not listed, start with the medium setting. If more crispness is desired,
remove the lid or aluminum foil. Most foods can be kept at serving temperatures by using the medium setting. When a combination of
foods are to be kept warm (for instance, a meat with 2 vegetables and rolls), use the high setting. Refrain from opening the warmer drawer
while in use to eliminate loss of heat from the drawer. Open only for adding or removing food.
Convection Cooking (some models)
The convection oven uses a fan located in the rear wall of the oven to circulate heated air around the food to be cooked. The controlled air
flow pattern quickly seals the food surface retaining the natural juices and flavor. This method of cooking enables you to obtain the best
culinary results when baking, thawing, dehydrating and roasting foods.
Convection notes:
1. Most recipes can be made with temperatures set at 13°C (25°F) lower than temperatures required for normal radiant cooking methods.
Refer to the electronic oven control operating instructions included in section “Electronic Oven Control” of this Use & Care Guide. This
can result in considerable reduction of food shrinkage and more tender meats.
2. Batch cooking is more convenient with better results.
3. Defrosting is quicker in convection mode when compared to regular radiant cooking.
4. Remember to use tested recipes with times adjusted for convection baking/roasting when using the convection mode. Times may be
reduced by as much as 30% when using the convection feature.
Convection Roasting (some models)
When convection roasting, use the broiler pan and grid, and the roasting rack. The broiler pan will
catch grease spills and the grid will help prevent grease spatters. The roasting rack will hold the
meat.
1. Place oven rack on bottom or next-bottom rack position.
2. Place the grid in the broiler pan. The roasting rack fits on the grid allowing the heated air to
circulate under the food for even cooking and helps to increase browning on the underside.
Make sure the roasting rack is securely seated on the grid in the broiler pan. DO NOT use the
broiler pan without the grid or cover the grid with aluminum foil.
Food Item Setting Food Item Setting Food Item Setting
Bacon HI Ham MED Potatoes (baked) HI
Biscuits MED Hamburger Patties HI Potatoes (mashed) MED
Casseroles MED Pancakes, Waffles HI Poultry HI
Eggs MED Pastries MED Roast (Beef, Pork, Lamb) MED
Empty Dinner Plate LO Pies MED Rolls, soft LO
Fish, Seafood MED Pizza HI Rolls, hard MED
Fried Foods HI Pork Chops HI Vegetables MED
Gravies MED
Warmer Drawer Recommended Food Settings Chart
NOTE: The convection fan automatically turns off when the oven door is opened while oven is in a convection mode and
resumes when the door is closed again.

General 9 information
Oven Baking
For best cooking results, heat the oven before baking cookies, breads, cakes, pies or pastries, etc... There is no need to preheat the oven for
roasting meat or baking casseroles.
The cooking times and temperatures needed to bake a product may vary slightly from your previously owned appliance.
Air Circulation in the
Oven
For good air circulation in the oven and best
baking results, center pans as much as pos-
sible. Allow 5.1 to 10.2 cm (2” to 4”) around
the utensil(s) for proper air circulation and be
sure pans do not touch each other, the door,
sides or back of oven. The hot air must circu-
late around the pans for even heat to reach all
parts of the oven.
If using multiple pans, stagger as shown. If using one pan, place in center of oven.
BakingProblems
Cookiesandbiscuits
burn on the bottom.
Cakes too dark on
top or bottom
.
Cakes not done in the
center.
Cakes not level.
Foodsnot donewhen
cookingtimeisup.
Causes
• Cookies and biscuits put into the
oven before the preheating time is
completed.
• Oven rack overcrowded.
• Dark pan absorbs heat too fast.
• Cakes put into the oven before
preheating time is completed.
• Oven rack position too high or low.
• Oven too hot.
• Oven too hot.
• Incorrect pan size.
• Pan not centered in the oven.
• Range not level.
• Pan too close to oven wall or rack
overcrowded.
• Pan warped.
• Oven too cool.
• Oven overcrowded.
• Oven door opened too frequently.
Corrections
• Allow oven to preheat to the selected temperature before
placing food in oven
.
• Choose pan sizes that will permit 5.1 cm to 10.2 cm (2" to 4")
of air space on all sides when placed in the oven.
• Use a medium-weight aluminum baking sheet.
• Allow oven to preheat to the selected temperature before
placing food in the oven.
• Use proper rack position for baking needs.
• Set oven temperature 25°F/12°C lower than recommended.
• Set oven temperature 25°F/12°C lower than recommended.
• Use pan size suggested in recipe.
• Use proper rack position and place pan so there is 5.1 cm to
10.2 cm (2" to 4") of space on all sides of pan.
• Place marked glass measuring cup filled with water on the
center of the oven rack. If water level is uneven, refer to the
installation instructions for levelling the appliance.
• Be sure to allow 5.1 cm to 10.2 cm (2" to 4") of clearance on
all sides of each pan in the oven.
• Do not use pans that are dented or warped.
• Set oven temperature 25°F /12°C higher than suggested and
bake for the recommended time.
• Be sure to remove all pans from the oven except the ones to be
used for baking.
• Open oven door only after shortest recommended baking
time.
Baking Problems and Solutions Chart

General 10 information
Open door to the "Broil
Stop" position when broiling
Be sure the oven is unplugged and all parts are COOL before replacing the oven light bulb. Do not turn the oven light on
during the self-cleaning cycle. High temperature will reduce lamp life.
Broiling
Broiling is a method of cooking tender cuts of meat by direct heat under the broil element of the oven.
Preheating
Preheating is suggested when searing rare steaks. (Remove the broiler pan before preheating. Foods will
stick if placed on hot metal.) To preheat, set the oven control(s) to BROIL as instructed in the Owner’s Guide.
Wait for the element to become red-hot, usually about 2 minutes. Preheating is not necessary when broiling
meats well-done.
To Broil
Broil on one side until the food is browned; turn and cook on the second side. Season and serve. Always pull rack out to the “stop” position
before turning or removing food.
Determining Broiling Times
Broiling times vary, so watch the food closely. Time not only depends on the distance from the element, but on the thickness and aging of
meat, fat content and doneness preferred. The first side usually requires a few minutes longer than the second. Frozen meats also require
additional time.
Broiling Tips
The broiler pan and its grid allow dripping
grease to drain and be kept away from the
high heat of the broiler.
DO NOT use the pan without its grid. DO NOT cover the grid with foil. The exposed grease could
ignite.
Should an oven fire occur, close the oven door and turn off the oven. If the fire continues,
throw baking soda on the fire or use a fire extinguisher. DO NOT put water or flour on the fire. Flour may
be explosive.
Broiler Clean-Up Tips:
• To make cleaning easier, line the bottom of the broiler pan with aluminum foil. DO NOT cover the broiler grid with foil.
• To prevent grease from baking on, remove the broiler pan from the oven as soon as cooking is completed. Use hot pads because the
broiler pan is extremely hot. Pour off grease. Soak the pan in HOT, soapy water.
• Clean the broiler pan as soon as possible after each use. If necessary, use soap-filled steel wool pads. Heavy scouring may scratch the
grid.
Changing Oven Light
On some models an interior oven light will turn on automatically when the oven door is opened.
The oven light may be turned on when the door is closed by using the oven light switch located on the control panel.
On a self clean oven the lamp is covered with a glass shield held in place by a wire holder.
THIS GLASS SHIELD MUST BE IN PLACE WHENEVER THE OVEN IS IN USE.
To replace the light bulb:
CAUTION: BE SURE OVEN IS COOL
1. Turn the power off at the main source.
2. Wear a leather-faced glove for protection against possible broken glass.
3. Replace bulb with a 40 watt appliance bulb only.
4. For self-cleaning oven, press wire holder to one side to release glass shield, change bulb and be sure
to replace glass shield.
Always pull oven rack out to the “stop” position before
turning or removing food.

General 11 information
General Cleaning
Cleaning Various Parts of Your Range
Before cleaning any part of the range, be sure all controls are turned OFF and the range is COOL. REMOVE SPILLOVERS AND
HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANING WILL REDUCE THE NUMBER OF MAJOR CLEANING LATER.
Surfaces
Aluminum & Vinyl
Control Panel and Trim Pieces
Glass, Painted and Plastic
ControlKnobs,BodyParts,and
Decorative Trim
StainlessSteel (some
models) Oven Door & Drawer
Front Panel
SealedBurnerUnits
Burner Cap, Trim Ring (some
models), Burner Pans (some
models), and Burner Base
PorcelainEnamel
BurnerGrates
Cooktop, Broiler Pan and Insert,
Door Liner, Body Parts and
Warmer Drawer and Drawer
Cavity
How to Clean
Use hot, soapy water and a cloth. Dry with a clean cloth.
Beforecleaningthecontrolpanel,turnallcontrolstoOFFandremovethecontrolknobs.To
remove,pulleachknobstraightofftheshaft.Cleanusinghot,soapywaterandadishcloth.
Rinsewitha clean water and a dishcloth. Cover stubborn spots with an ammonia-soaked
papertowelfor30to40minutes.Rinse.Besuretosqueezeexcesswaterfromtheclothbefore
wipingthepanel;especiallywhenwipingaroundthecontrols.Excesswaterinoraroundthe
controls may cause damage to the appliance. Be sure to rinse the cleaners as bluish stains
mayoccur duringheatingandcannot beremoved.Toreplace knobsaftercleaning, line up
the flat sides of both the knob and the shaft; then push the knob into place.
For general cleaning, use hot, soapy water and a cloth. For more difficult soils and built-up
grease,applyaliquiddetergentdirectlyontothesoil.Leaveonsoilfor30to60minutes.Rinse
with a damp cloth and dry. DO NOT use abrasive cleaners on any of these materials; they
canscratch.Toremovecontrolknobs,turntotheOFFposition;graspfirmlyandpullstraight
offtheshaft.Toreplaceknobsaftercleaning,lineuptheflatsidesofboththeknobandthe
shaft; then push the knob into place.
CleanersmadeespeciallyforstainlesssteelasStainlessSteelMagic,orothersimilarcleaners
are recommended. Always follow the manufacturer's instructions. Be sure to rinse the
cleaners as bluish stains may occur during heating and cannot be removed.
Theholesintheburnerofyourrangemustbekeptcleanatalltimesforproperignitionand
acomplete,evenflame.Cleantheburnersroutinelyandespeciallyafterbadspilloverswhich
could clog these holes.
Toremove,cleanandreplacetheentireburnercap assembly,follow theinstructions under
General Cleaning. DO NOT put burner parts in the dishwasher.
Cleaninthedishwasherand dry upon removal. If soil are not removed, follow thecooktop
cleaninginstructionsbelow.
Gentlescouringwithasoapyscouringpadwillremovemostspots.Rinsewitha1:1solution
of clear water and ammonia. If necessary, cover difficult spots with an ammonia-soaked
papertowelfor30-40minutes.Rinsewithclearwateranddampcloth,andthenscrubwith
asoap-filledscouringpad.Rinseandwipedrywithacleancloth.Removeallcleanersorthe
porcelainmaybecomedamageduringfutureheating.DONOTusesprayovencleanerson
therangetop.

General 12 information
General Cleaning (continued)
To Clean the Cooktop Glass
Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop is
COOL.
The cooktop is designed to make cleaning easier. Because the burners are sealed, cleanups are easy when
spillovers are cleaned up immediately. Remove burner grates before cleaning. To clean the cooktop, wipe
with a clean, damp cloth and wipe dry.
Correct and consistent cleaning is essential to maintaining your heat-resistant glass top. Spills and spatters
should be wiped up using a clean paper towel and sudsy water. This should be done either as soon as
possible after the spill occurs, after cooking is completed, or at the latest, before using the cooktop again.
Use caution if the cooktop is hot. For heavy spills, spatter or burned-on materials, use a razor blade scraper.
Hold the razor blade scraper at a 30° angle and remove food spills or burned on food residue.
Forsugary spillovers:
Sugary spills can cause pitting of your cooktop surface. Therefore, you must begin cleaning the spills while
the cooktop is still hot.
Finish the cleaning process by applying a recommended heat-resistant glass cooktop cleaning creme.
Apply cleaner with clean, damp paper towel. Rinse with a paper towel dampened with clean water and
wipe dry. Always wipe the cooktop thoroughly to avoid heating any cleaner residue.
Do not use commercial oven cleaners on any part of the cooktop. Damage to the finish or parts could result.
DO NOT use the following on the heat-resistant glass cooktop:
•Abrasive plastic, nylon, metal scouring or cloth pads. They may scratch the cooktop and make it more difficult to clean later. Always use
a new, clean paper towel when cleaning the heat-resistant glass top.
•Anything that may melt (plastics, aluminum foil, sugar or food with a high sugar content).
•Heavy duty cleansers, rust or stain removers.
•Chlorine bleach, ammonia, hydrofluoric acid or any other kind of chemical cleaners. They may etch or discolor the cooktop.
•Sponges, cloths or dish towels. Always use a new, clean paper towel when cleaning the cooktop. Lint or soil remaining on the cooktop
from a cloth or sponge can burn and cause discoloration.
To Clean the Burner Grates, Contoured Burner Pans, Burner Cap, and Burner
Base
The burner grates, contoured burner pans, burner caps and burner base should be routinely cleaned. Keeping the burner ports clean will
prevent improper ignition and an uneven flame. See instructions below.
To Clean the Burner Grates
Be sure burners and grates are cool before you place your hand, a pot holder, cleaning cloths or other
material on them. The cast iron burner grates can be washed in hot soapy water. Rinse thoroughly and
dry the grates with a cloth- don't put them on the cooktop while still wet. Be sure the grates are
positioned securely over the burners.
To remove burned on food, place the grates in a covered container or heavy plastic bag. Add 1/4 cup
ammonia and soak for 30 minutes. Wash, rinse well and dry. An abrasive cleaner can be used for
stubborn stains.
To Clean the Contoured Burner Pans
The square burner pans are attached to the cooktop and are not removable. The burner pan forms a
recessed well area located around each burner unit. If a spill occurs in one of the well areas, blot up spill
with an absorbent cloth. Rinse with a clean, damp cloth and wipe dry.
Remove burner grates
before cleaning. Heavy
burned-on spills can be
removed with a razor
blade scraper. Use
caution to avoid
damagingsurface.
Burner Grates
(some models)

General 13 information
General Cleaning(continued)
To Clean the Burner Grates, Contoured Burner Pans, Burner Cap and Burner
Base (continued)
To Clean the Burner Cap
Use a soap-filled scouring pad or a mild abrasive cleanser to clean burner caps and trim
rings. If necessary, cover difficult spots with an ammonia-soaked paper towel for 30 to
40 minutes. Rub gently with a soap-filled scouring pad and rinse with a mixture of clean
water and vinegar. Wipe dry. Remove all cleaners or the porcelain may become damaged
during future heating.
To Clean the removable Burner Base and Gas Opening
The ports (or slots) around the burner base must be routinely cleaned. Use a small-
gauge wire or needle to clean small slots or holes.
Note: If the electrode is damaged or broken, the surface burner will not light. Manual
lighting with a match is still possible.
For proper flow of gas and ignition of the burner—DO NOT ALLOW SPILLS, FOOD,
CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE GAS OPENING. Gas must
flow freely through the small hole in the brass orifice for the burners to light properly. If
the orifice gas opening becomes soiled or clogged, use a small-gauge wire or needle to
clean. ALWAYS keep the burner cap assembly in place whenever a surface burner is in
use.
To Replace the Burner
Make sure the pieces are dry before placing back on the burner.
1. Replace burner base at it place. Put back burner cap. Make sure each burner cap is
properly aligned and level.
2. Turn the burner on to determine if it will light. If the burner does not light after
cleaning, contact an authorized servicer. Do not service the sealed burner yourself.
Cleaning the Self-Clean Oven (some models)
Adhere to the following cleaning precautions:
- Allow the oven to cool before cleaning.
- Wear rubber gloves when cleaning any exterior parts of the oven manually.
During the self-clean cycle, the outside of the wall oven can become very hot to the touch. DO NOT leave small children
unattended near the appliance.
Before cleaning any part of the oven, be sure the electronic oven control is turned off or else push CANCEL pad. Wait until
the oven is cool.
DO NOT use commercial oven cleaners or oven protective coatings in or around any art of the self-cleaning oven. DO NOT clean the oven
door gasket. The gasket on the oven door is essential for a good seal. Care should be taken not to rub, damage or move the gasket. DO
NOT cooking or foil could melt and damage the oven surface.
A self-cleaning oven cleans itself with high temperatures (well above cooking temperatures) which eliminate soil completely or reduce it to
a fin powdered ash you can which away with damp cloth.
Do not operate the
burners without the burner base and
the burner cap in place.

General 14 information
General Cleaning (continued)
Cleaning the Self-Clean Oven (some models) (continued)
Preparing the Oven for Self-Cleaning
1. Remove an excess spillovers in the oven cavity before starting the self-cleaning cycle. To
clean, use hot soapy water and a cloth. Large spillovers can cause heavy smoke or fire when
subjected to high temperatures. DO NOT allow food spills with a high sugar or acid content
(such as tomatoes, sauerkraut, fruit juices or pie filling) to remain on the surface as they may
cause a dull spot even after cleaning.
2. Clean any soil from the oven frame and the door liner (see illustration). These areas heat
sufficiently during self-cleaning cycle to burn soil on. Clean with soap and water.
3. Remove the broiler pan and insert, all utensils and any foil. These items do not withstand
high cleaning temperatures
4. Oven racks may be left in the oven or may be removed. If they go through the clean cycle,
their color will turn slightly dull. After the cycle is completed and the oven has cooled, rub
the sides of the racks with wax paper or a cloth containing a small amount of baby oil or
salad oil. This will make the racks glide easier.
What to Expect During Cleaning
While the oven is in operation, the oven heats to temperatures much higher than those used in normal cooking. Sounds of metal expansion
and contraction are normal. Odor is also normal as the food soil is being removed. Smoke may appear through the oven vent, located on the
top of the control panel.
If heavy spillovers are not wiped up before cleaning, they may flame and cause more smoke and odor than usual. This is normal and safe and
should not cause alarm. If available, use an exhaust fan during the self-cleaning cycle.
NOTE: A smoke eliminator in the oven vent converts most of the soil into a colorless vapor.
Setting the Controls for Clean Cycle
For the setting of the clean cycle, refer to Timer or Electronic Oven Control section.
To Remove and Replace Oven Door
1. Open the door to the fully opened position.
2. Pull up the lock located on both hinge supports and engage it in the hook of the hinge levers. You may have to apply a little
downward pressure on the door to pull the locks fully over the hooks.
3. Grab the door by the sides, pull the bottom of the door up and toward you to disengage the hinge supports.
Keep pulling the bottom of the door toward you while rotating the top of the door toward the range to completely disengage the
hinge levers.
4. Proceed in reverse to reinstall the door.
Make sure the hinge supports are fully engaged before unlocking the hinge levers.
The door is heavy. For safe, temporary storage, lay the door flat with the inside of the door facing down.
Lock in normal
position Lockengaged for door removal HINGESLOTDoor removed from the range
DONOTHAND
CLEAN SEAL
DOHAND
CLEAN
FRAME
DOHAND
CLEANDOOR

General 15 information
1.Grasp the sides of the glass panel and carefully insert the glass into the door top moulding.
2.Replace the support rail and the 5 locking screws.
3.Replace the door onto the range as shown above.
To Remove and Replace Warmer Drawer (some models)
To Remove Warmer Drawer:
1. Turn power off before removing the warmer drawer.
2. Open the drawer to the fully opened position.
3. Locate the latches on both sides of the warmer drawer. The left latch is visible. However, the right
side is not and is located inside the drawer glides.
4. Pull up on the left glide latch while inserting a screwdriver over the right latch and pushing down.
5. Pull the drawer away from the range.
6. To clean warmer drawer, gently scour with a soapy scouring pad, this will remove most spots. Rinse
witha1:1 solution of clearwater and ammonia. Ifnecessary, cover difficult spotswithan ammonia-
soaked paper towel for 30 to 40 minutes. Rinse with clean water and a damp cloth. Remove all
cleaners or the porcelain may become damaged during future heating. DO NOT use spray oven
cleaners on the cooktop.
To Replace Warmer Drawer:
1. Align the glide latches on both sides of the drawer with the slots on the drawer.
2. Push the drawer back into the range.
Electrical Shock Hazard can occur and result in serious injury or death. Disconnect appliance from
electric power before cleaning and servicing the warmer drawer.
Storage Drawer (some models)
Use the storage drawer for storing cooking utensils. The drawer can de removed to facilitate cleaning under the range. Use care when
handling the drawer.
To open the storage drawer, push the drawer in gently and it will spring open. To close, push the drawer until you hear a click, which
indicates that the spring is compressed, and the drawer is closed.
To remove the drawer:
1. Pull empty drawer out to the roller guide stop.
2. Tilt the drawer up and pull it out over the rollers.
To replace the drawer:
1. Insert the rear end of the drawer into the opening.
2. Fit the drawer end rollers onto the guide rails.
3. Push the drawer in until it stops, then lift to allow the rollers to clear the roller guide stop,
and push in.
General Cleaning (continued)
Removable Outer Door Glass Panel (some models)
Applicable only to models with an external glass panel not held with a frame. This design allows you to clean the inside face of the exterior
door panel as well as the hidden face of the door inner glass.
To Remove the External Door Glass Panel:
1.Remove the door as shown above and lay the door flat.
2.Using a screwdriver, remove the screws fastening the metal glass support rail to the underside of the door. Remove the support rail.
3.Grasp both sides of the glass panel and slowly pull it out of the door upper molding. Lay the glass flat.
Handle the glass panel with care. When dropped on a corner, the glass panel may shatter.
To Replace the External Door Glass Panel:
WarmerDrawer

General 16 information
Notes

AVOID SERVICE CHECKLIST
1
AVOID SERVICE CHECKLIST
Before you call for service - read this
You may save the cost and inconvenience of an unnecessary service call by first reviewing this easy to use Avoid-
Service Check List of the most frequently encountered situations that are not the result of defective workmanship
of materials.
You will be charged for a service call while the appliance is in warranty if the problem is not caused by defective
product workmanship or materials.
Your new appliance is a carefully engineered product. Many times, what appears to be a reason to call for service
requires nothing more than a simple adjustment you can easily make in your own home or is normal operating
characteristic of appliance under certain conditions.
This list is applicable to a variety of models; some of the items will not necessarily apply to your appliance.
PROBLEM POSSIBLE CAUSE / SOLUTION
INSTALLATION
PRINTED IN CANADA 318130502 (9909) Rev. .B
RANGE DOES NOT OPERATE
Range is not level.
Cannot move appliance easily.
Appliance must be accessible for
service.
Entire range or oven does not
operate.
Oven does not operate.
Poor installation. Place oven rack in center of oven. Adjust leveling legs (slide-in models) at
base of range until the oven rack is level.
Be sure floor is level and is strong and stable enough to adequately support range.
If floor is sagging or sloping, contact a carpenter to correct the situation.
Kitchen cabinet alignment may make range appear unlevel. Be sure cabinets are square and
have sufficient room for range clearance.
Cabinets not square or are built in too tightly. Contact builder or installer to make appliance
accessible.
Carpet interferes with range. Provide sufficient space so range can be lifted over carpet.
Make sure cord/plug is plugged tightly into outlet .
Service wiring is not complete. Contact your dealer, installing agent or authorized servicer.
Power outage. Check house lights to be sure. Call your local electric company for service.
Oven control beeps and displays F1 or F3. Electronic control has detected a fault condition.
Push the CANCEL pad to clear the display and stop the beeping. Reprogram oven. If fault
recurs, record fault number, push CANCEL pad and contact authorized servicer.

AVOID SERVICE CHECKLIST
2
PROBLEM POSSIBLE CAUSE / SOLUTION
RANGE DOES NOT OPERATE (continued)
SURFACE UNITS
Oven light does not work.
Surface unit does not heat.
Surface units too hot or not hot
enough.
Drip bowls are pitting or rusting.
Drip bowls turning color or dis-
torted out of shape.
Scratches or abrasions on cooktop
surface.
Metal marks.
Brown streaks or specks.
Areas of discoloration with metal-
lic sheen.
Replace or tighten bulb. See Changing Oven Light in this Owner’s Guide for instructions.
No power to the appliance. Check steps under “Entire Appliance Does Not Operate” in this
Avoid Service CheckList.
Incorrect control setting. Make sure the correct control is on for the surface unit to be used.
Incorrect control setting. Make sure the correct control is on for the surface unit to be used.
Lightweight or warped pans used. Use only flat, evenly balanced, medium or heavyweight
cookware. Flat pans heat better than warped pans. Cookware materials and weight of the
material affect heating. Heavy-and medium- weight pans heat evenly. Because lightweight
pans heat unevenly, foods may burn easily.
Foods with acids, such as tomatoes, if allowed to stand in/on bowls will cause corrosion.
Remove and wash drip bowls as soon as possible after a spillover.
Normal environment. Houses along sea coast are exposed to salt air. Protect bowls as much as
possible from direct exposure to salt air.
Bottom surface of cookware extends beyond surface elements and touches cooktop surface.
This can cause high enough temperatures to discolor the drip bowls. DO NOT use cookware of
this type. Pan sizes should be matched to the size of the element. Replacement drip bowls
may be purchased from your dealer.
Coarse particles such as salt or sand between cooktop and utensils can cause scratches. Be
sure cooktop surface and bottoms of utensils are clean before usage. Small scratches do not
affect cooking and will become less visible with time.
Cleaning materials not recommended for ceramic-glass cooktop have been used. See
“Ceramic-Glass Cooktop Cleaning” in the General Cleaning section.
Cookware with rough bottom has been used. Use smooth, flat-bottomed cookware.
Sliding or scraping of metal utensils on cooktop surface. Do not slide metal utensils on
cooktop surface. Use a ceramic-glass cooktop cleaning creme to remove the marks. See
“Ceramic-Glass Cooktop Cleaning” in the General Cleaning section.
Boilovers are cooked onto surface. Use razor blade scraper to remove soil. See “Ceramic-
Glass Cooktop Cleaning” in the General Cleaning section.
Mineral deposits from water and food. Remove using a ceramic-glass cooktop cleaning
creme. Use cookware with clean, dry bottoms.
CERAMIC GLASS COOKTOP (some models)