Front Runner RRAC133 User manual

RRAC133_REV_A00 © COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
Antenna Mount
RRAC133
ENG
1
IMPORTANT WARNING!
Thank you for purchasing a Front Runner Antenna Mount.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
FRONT RUNNER CAN NOT RECOMMEND A MAXIMUM LOAD CARRYING CAPACITY. PLEASE REFER TO YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS. IT IS CRITICAL
THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS
TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE
INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

RRAC133_REV_A00 © COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
1 1 X Antenna Mount
2 1 X Antenna Base Plate
3 2 X M6 x 12 x 1SS Flat Washer
4 2 X M6 Nyloc
5 2 X M6 Nut Cap
6 3 X M8 x 20 Button Head Bolt
7 3 X M8 x 16 x 1.6SS Flat Washer
8 3 X M8 Nyloc Nuts
IN THE BOX
FIGURE 1.1
10mm 5mm
4mm
GET ORGANIZED
1
1
3
4
5
2
6
7
8
7
6

RRAC133_REV_A00 © COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS 3
PREPARATION
2
2.1
2.2
2.3
Decide where on the Side Profile you would
like to mount your antenna. Remove the
corner closest to that position.
Slide 2 M8 Nyloc Nuts (Item 8) into the Side
Profile. Place the Antenna Mount (Item 1)
over the Side Profile as shown. Loosely
secure the Antenna Mount at the top using
M8 x 20 Button Head Bolts and M8 x 16 x
1.6SS Flat Washers (Items 6 & 7).
Align the bottom slot in the Antenna Mount
with the bottom hole in the Side Profile.
Using a M8 x 20 Button Head Bolt and M8 x
16 x 1.6SS Flat Washer Secure the Antenna
Mount to the Side Profile.
Fully tighten all the bolts and refit the
corner.
If you have a antenna with a magnetic base
you will need the fit the Antenna Base Plate
(Item 2) using M6 Nyloc Nuts and M6 x 12 x
1SS Flat Washers (Items 3 & 4) as shown.
Place M6 Nut Caps (Item 5) on the Nyloc
Nuts after tightening.
8
2
1
3
4
5
4mm
4mm
10mm
5mm
6
7
1
7
6

RRAC133_REV_A00
4
© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
COMPLETION
3
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or Online.
9
3.1
Congratulations! You did it. Take a step back and admire your work!
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on: