Eagle Group Dunnage User manual

ASSEMBLY INSTRUCTIONS
Dunnage Rack
stationary
mobile
Parts List
Stationary Dunnage
#description qty
1. . . Dunnage matt . . . . . . . . . . . 1
2. . . 4-sided frame . . . . . . . . . . . 1
3. . . 3-sided frame . . . . . . . . . . . 1
4. . . Bags of four pairs
of split sleeves. . . . . . . . . . . 2
5. . . Posts . . . . . . . . . . . . . . . . . . 4
* 2 swivel casters, 2 with brake
Mobile Dunnage
#description qty
1. . . Dunnage matt . . . . . . . . . . . 1
2. . . 4-sided frame . . . . . . . . . . . 1
3. . . 3-sided frame . . . . . . . . . . . 1
4. . . Bags of four pairs
of split sleeves. . . . . . . . . . . 2
5. . . Posts . . . . . . . . . . . . . . . . . . 4
6. . . Donut bumpers . . . . . . . . . . 4
7. . . Casters*. . . . . . . . . . . . . . . . 4
#4
#5
#4
#5
#6
#7
pair of split sleeves
#4
CAUTION
INSPECT CONTENTS IMMEDIATELY AND FILE CLAIM WITH DELIVERING
CARRIER FOR ANY DAMAGE. SAVE YOUR BOX AND ALL PACKING MATERIALS.
YOU ARE RESPONSIBLE FOR DAMAGE TO YOUR UNIT IF RETURNED IMPROPERLY PACKED.
Eagle Foodservice Equipment, Eagle MHC, and SpecFAB®are divisions of Eagle Group. ©2023 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A.
• Phone: [phone] • 800/441-8440
• Fax: [phone] • www.eaglegrp.com
INSTRUCTION SHEET
#A214470
EG9829 Revised 09/23
#1
#2
#3
• Remove all components from packaging. Using the Parts List (above), check and identify all components.
• Split sleeves must be used in conjunction with the three-sided and four-sided frames. When installing split sleeves, make sure the
thicker part of the taper goes toward the bottom. Also make sure the rib inside the split sleeves is seated into the groove on the post.
Posts are grooved in 1˝ increments.
• When installing frames, make sure the thicker part of the collars goes toward the bottom.
PLEASE READ BEFORE ASSEMBLING DUNNAGE RACK…
(continued on back page)

Stationary Dunnage Racks
1. Assemble 3-sided frame to posts.
A. Snap plastic tapered split sleeves onto each post at the desired
position for the 3-sided frame (see Figure 1a).
Note: Although the 3-sided frame should be mounted as low as
possible for the most stability, NSF requires a minimum of
6˝ clearance below the frame. For NSF-approved installation,
mount frame at the 6th groove or above on each post.
B. Holding the 3-sided frame on its side, insert the posts through the
corner collars until the split sleeves are seated snugly within the
collars (see Figure 1b).
2. Assemble 4-sided frame.
A. Stand the post/frame assembly upright, and snap the split sleeves
onto each post at the 1st groove from the top (see Figure 2a).
B. Mount the 4-sided frame, inserting the posts through the corner
collars until the split sleeves are seated snugly within the collars
(see Figure 2b).
3. Complete assembly.
A. Securely seat both frames using a board and hammer at each
corner (see Figure 3a).
B. Place the dunnage matt on the frame (see Figure 3b).
Mobile Dunnage Racks
1. Assemble casters to posts.
A. Place donut bumpers onto bottom end of post. Bottom of post is the
end with 17⁄16˝ ungrooved (see Figure 1a).
B. Insert caster stem into bottom of each post. Drive in caster using a
hammer or mallet (see Figure 1b).
Note: If rigid casters are purchased, place alignment channel (Figure
1c) over caster stem before inserting casters.
2. Complete assembly following directions for stationary dunnage
racks (above). Always place the 3-sided frame at the lowest
position for mobile dunnage racks.
Figure 1a
Figure 1b
split sleeves
3-sided
frame
post
post
corner collar
Figure 2b
3-sided
frame
post
4-sided frame
Figure 2a
post split sleeves
Figure 3a
Figure 3b
dunnage matt
Figure 1a
caster
post
caster
stem
bumper
Figure 1b
Figure 1c
alignment
channel
rigid casters (End)
(End)
Eagle Foodservice Equipment, Eagle MHC, and SpecFAB®are divisions of Eagle Group. ©2023 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A.
• Phone: [phone] • 800/441-8440
• Fax: [phone] • www.eaglegrp.com
ASSEMBLY INSTRUCTIONS
Dunnage Rack