Fuslon XS Series User manual

®
XS Series Speakers Installation Instructions .................................................................................... 2
Instructions d'installation des haut-parleurs XS Series ..................................................................... 6
Altoparlanti XS Series Istruzioni di installazione ............................................................................. 11
Lautsprecher der XS Series – Installationsanweisungen ................................................................15
Instrucciones de instalación de los altavoces de la XS Series ....................................................... 19
Instruções de instalação dos alto-falantes XS Series ..................................................................... 23
XS Series luidsprekers installatie-instructies .................................................................................. 27
Garmin®, the Garmin logo, FUSION®, the Fusion logo, and True-Marine™ are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used
without the express permission of Garmin.
October 2018
190-02481-90_0A

XS Series Speakers Installation
Instructions
Important Safety Information
WARNING
Failure to follow these warnings and cautions could result in
personal injury, damage to the vehicle or vessel, or poor product
performance.
This device must be installed according to these instructions.
Disconnect the vehicle's or vessel's power supply before
beginning to install this product.
CAUTION
Continuous exposure to sound pressure levels over 100 dBA
may cause permanent hearing loss. The volume is typically too
loud if you cannot hear people speaking around you. Limit the
amount of time you listen at high volume. If you experience
ringing in your ears or muffled speech, stop listening and have
your hearing checked.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
It is strongly recommended that you have your audio system
installed by a professional installer to ensure optimum
performance.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation, go
to www.fusionentertainment.com for product support.
What's In the Box
• 2 speakers
• 12 Phillips stainless steel mounting screws
◦ 4 in. models: 3.5 mm x 25.4 mm (6 gauge x 1 in.)
◦ 6.5 in. and 7.7 in. models: 4.2 mm x 25.4 mm (8 gauge x 1
in.)
• Mounting template
• Speaker grilles
Tools Needed
• Electric drill
• Drill bit (size varies based on surface material)
• Phillips screwdriver
• Wire strippers
• Crimping tool
• Electrical tape
• Appropriate saw or utility knife to cut surface material
• Marine sealant (optional)
NOTE: For customized installations, additional tools and
materials may be needed.
Mounting Considerations
NOTICE
When mounting the speaker in an area exposed to weather or
water, you must mount the speaker on a vertical surface. If you
mount the speaker on a horizontal surface facing up, water can
gather in and around the speaker, causing damage over time.
Selecting the correct mounting location is critical to optimize the
performance of each speaker. FUSION® speakers are designed
to perform in the widest possible range of mounting locations,
but the more you plan the installation, the better the speakers'
sound will be.
• For the best performance, you should mount the speakers
higher in the boat. Sound travels in the direction in which the
speakers are facing, so if you mount them in a lower location,
the sound quality and volume may not be not ideal.
• If you intend to mount the speakers outside the boat, you
must mount them in a location well above the waterline,
where they are not submerged or damaged by docks, pilings,
or other pieces of equipment. When mounted correctly, these
speakers are rated IP65 for protection from the front of the
speaker. Water exposure and damage to the rear of the
speaker voids the warranty. This includes situations when the
speakers are mounted in a sealed enclosure, especially if
they are exposed to wash down. Using an enclosure with a
port or vent exposed to the outside environment may allow
water to collect and damage the speaker.
• You should select mounting locations that enable you to hear
sound from both speakers at the same time to achieve a
sound stage effect. To achieve this effect, you should not
mount the speakers side-by-side.
• When possible, you should select mounting locations where
the area behind each speaker is enclosed.
• You must select mounting locations that provide sufficient
clearance for the mounting depth of the speakers as
specified in the product specifications.
• For better bass performance, you should select mounting
locations that provide the appropriate space behind the
speaker according to the optimum enclosure design
requirements in the specifications section. Too small an area
restricts bass, and too large an area compromises bass
performance. Also, mounting a speaker close to an open
area (where sound from the back of the speaker has a very
short path to compete with sound from the front of the
speaker) produces the least bass.
• When a speaker is not exposed to the outside environment,
you can achieve a better bass performance using an
enclosure with a ported design.
• You can reference the Thiele Small (T/S) parameters in the
specifications section when designing a custom enclosure for
the speakers.
• You should select a flat mounting surface for the best seal.
• You should protect the speaker wires from sharp objects and
always use rubber grommets when wiring through panels.
• You should select mounting locations that avoid potential
obstacles, such as fuel and hydraulic lines and wiring.
• You should protect all terminals and connections from
grounding and from each other. Failure to do so could result
in permanent damage to the audio system and void the
product warranty.
• To avoid interference with a magnetic compass, you should
not mount the speakers closer to a compass than the
compass-safe distance value listed in the product
specifications.
• You must turn off the audio system before making any
connections to the source unit, amplifier, or speakers. Failure
to do so could result in permanent damage to the audio
system.
Mounting the Speakers
Before mounting the speakers, you must choose a location
following the guidelines above.
Before cutting the mounting surface you should verify that there
is enough clearance for the speaker behind the surface. Refer to
the specifications for clearance information.
2 Installation Instructions

NOTICE
Do not apply grease or lubricant to the screws when fastening
the speakers to the mounting surface. Grease or other lubricants
can cause damage to the speaker housing.
1Route the wires from the source to the speaker location,
away from sources of electrical interference.
2Trim the template and make sure it fits in the selected
location.
3Orient the template so that the FUSION logo is right-side up
on the template.
4Secure the template to the selected location.
5Using a rotary tool or jigsaw, cut the mounting surface along
the inside of the line on the template.
6Place the speaker in the cutout to test the fit.
7If necessary, use a file and sandpaper to refine the size of
the cutout.
8After the speaker fits correctly in the cutout, ensure the
mounting holes on the speaker line up with the pilot holes on
the template.
9If the mounting holes on the speaker do not line up, mark the
new hole locations.
10Using an appropriately sized drill bit for the mounting surface
and screw type, drill the holes.
11Remove the template from the mounting surface.
12Connect the speaker wires À while observing polarity
(Speaker Wiring, page 3).
13If necessary, connect the LED wires (LED Wiring, page 3).
14Place the speaker in the cutout.
15Secure the speaker to the mounting surface using the
included screws Á.
NOTE: Do not over tighten the screws, especially if the
mounting surface is not flat.
16With the speakers mounted, hold the grille with the FUSION
logo at the bottom, or at the 6 o'clock position.
17Turn the grille counter-clockwise about 30 degrees, so the
FUSION logo is at the 5 o'clock position.
18Place the grille on the speaker, and twist it clockwise to
secure it.
NOTE: Instead of twisting to install the grille, you can line it
up so the FUSION logo is at the 6 o'clock position and press
to snap it into place.
Speaker Wiring
When connecting the speakers to your stereo, observe these
considerations.
• Speaker wire is not included with the speakers. You should
use 18 AWG (0.82 mm2) speaker wire to connect the
speakers to the stereo.
• The leads on the speakers are terminated using male spade
connectors. You should use female spade connectors (not
included) to connect the speaker wire to the speaker leads
for the best connection.
• You can use this table to identify the polarity and spade-
connector sizes of the leads on the speaker.
Speaker wire color Speaker wire
polarity
Spade connector
size
White Positive (+) 6.3 mm
White with a black
stripe
Negative (-) 4.8 mm
LED Wiring
Connecting the LED Wires
You can control the color of the LEDs by connecting the LED
color wires to ground. You can splice the ground wire to multiple
LED wires to customize the LED color.
NOTE: This feature is available only on the sports model.
NOTE: Instead of connecting the LED wires for one dedicated
color, you can install a remote control to turn the LEDs on and
off, change the color, and create lighting effects. See your
FUSION dealer or www.fusionentertainment.com for more
information.
The black wire on the LED cable is terminated with a 4 mm
female bullet connector, and the color wires are terminated with
4 mm male bullet connectors. You can connect these to 4 mm
bullet connectors on your wires (not included), or remove the
bullet connectors to connect to the bare wires instead.
1Connect a positive wire to the black wire on the LED cable.
2Connect a ground wire to the wire on the LED cable
according to the preferred LED color.
LED Color LED Wire Color
Red Red
Green Green
Blue Blue
Yellow Red and green
Magenta Red and blue
Cyan Blue and green
White Red, green, and blue
3Route the positive and negative wires, and connect them to a
power source (Connecting the LED Wires to Power,
page 3).
Connecting the LED Wires to Power
NOTE: This feature is available on only the sports model.
You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at
the power-source end of the cable. You should connect the
positive (+) power wire to a 12 Vdc power source through an
isolator switch or circuit breaker to turn the LEDs on and off. You
can use the same isolator or circuit breaker controlling the
power supply to your stereo, which allows you to turn the LEDs
and the stereo on and off at the same time.
You should use 22 AWG (0.33 mm2) or thicker wire to connect
the LEDs to the battery.
1Route the positive power (+) and negative ground (-) wires
from the LED-wire connections to the battery.
2Connect the negative wire to the negative (-) battery terminal.
3Connect the positive wire to the positive (+) terminal through
a 3 A fuse and isolator switch or circuit breaker.
Speaker Information
True-Marine™ Products
True-Marine products are subjected to rigorous environmental
testing under harsh marine conditions to surpass industry
guidelines for marine products.
Installation Instructions 3

Any product that bears the True-Marine stamp of assurance has
been designed for simplicity of use and combines advanced
marine technologies to deliver an industry leading entertainment
experience. All True-Marine products are supported by the
FUSION 3-year worldwide limited consumer warranty.
Registering Your XS Series
Help us better support you by completing our online registration
today.
• Go to www.fusionentertainment.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Cleaning the Speakers
NOTE: When mounted correctly, these speakers are rated IP65
for dust and water ingress protection under normal conditions.
They are not designed to withstand high pressure water spray,
which may occur when you wash down your vessel. Failure to
carefully spray-clean the vessel may damage the product and
void the warranty.
NOTICE
Do not use harsh or solvent-based cleaners on the speakers.
Using such cleaners may damage the product and void the
warranty.
1Clean all salt water and salt residue from the speaker with a
damp cloth soaked in fresh water.
2Use a mild detergent to remove a heavy buildup of salt or
stains.
Troubleshooting
Before you contact your FUSION dealer or service center, you
should perform a few simple troubleshooting steps to help
diagnose the problem.
If the FUSION speaker has been installed by a professional
installation company, you should contact the company so the
technicians can assess the problem and advise you about
possible solutions.
There is no sound coming from the speakers
• Verify that all connections from the source device and/or the
amplifier are connected correctly to the speaker terminals.
The system lacks bass or high frequencies
• Verify that the correct wire polarity is observed between the
source and speakers.
The wires should be connected positive to positive and
negative to negative.
• Verify that the speakers are attached firmly to the mounting
surface.
The audio is distorted
• Verify that the source volume is not too loud for the speaker,
and reduce the volume if necessary.
• Verify that the panels surrounding the speaker on the vessel
are not rattling.
• Verify that the source device and/or the amplifier are
connected to the speaker terminals correctly.
• If the speaker is connected to an amplifier, verify that the
input level of the amplifier is matched to the output level of
the stereo. For more information, see the manual for the
amplifier.
The LED lights will not turn on
• Verify that all wiring connections are correct and tight.
Specifications
Specification 4" Speakers 6.5"
Speakers
7.7"
Speakers
Peak power (Watts) 120 W 200 W 240 W
RMS power (Watts) 30 W 50 W 60 W
Efficiency (1 W/1 m) 87 dB 91 dB 92 dB
Frequency response 100 Hz to
18,000 Hz
80 Hz to
18,000 Hz
70 Hz to
18,000 Hz
Nominal impedance 4 ohms
Recommended
amplifier power
(RMS)
15 to 80 W per
channel
20 to 150 W
per channel
25 to 200 W
per channel
Min. mounting depth
(clearance)
54 mm (2 1/8 in.) 67 mm
(2 5/8 in.)
77 mm (3 in.)
Mounting diameter
(clearance)
99 mm (3 7/8 in.) 135 mm
(5 5/16 in.)
162 mm
(6 3/8 in.)
Optimum enclosure
volume
recommendation*
4 L (0.14 ft.3) 8 L (0.28 ft.3) 10 L
(0.28 ft.3)
LED color options
(Sports Model
Speakers only)
N/A RGB
LED Supply Voltage
(Sports Model
Speakers only)
N/A From 10.8 to 16 Vdc
LED Load Current at
14.4 Vdc (Sports
Model Speakers only)
N/A 150 mA
Operating
temperature range
From 0 to 50°C (from 32 to 122°F)
Storage temperature
range
From -20 to 70°C (from -4 to 158°F)
Cone/surround
material
Polypropylene
cone, rubber
surround
Polypropylene cone, cloth
surround
Water and dust rating IEC 60529 IP65 (Protected against dust and
water ingress.)
*Sealed enclosure, fully filled with absorption material.
NOTE: This speaker is not intended to be installed in a vented
or ported enclosure when exposed to the outside environment.
Speaker Dimensions
Dimension 4" Speakers 6.5" Speakers 7.7" Speakers
À135 mm
(5 5/16 in.)
177 mm (6 15/16 in.) 196 mm (7 11/16 in.)
ÁClassic grille:
17 mm (11/16 in.)
Classic grille:
17 mm (11/16 in.)
Sports grille:
19 mm (3/4 in.)
Classic grille:
20 mm (3/4 in.)
Sports grille:
23 mm (7/8 in.)
Â51 mm (2 in.) 64 mm (2 1/2 in.) 74 mm (2 7/8 in.)
Ã95 mm (3 3/4 in.) 130 mm (5 1/8 in.) 157 mm (6 3/16 in.)
4 Installation Instructions

Compass-Safe Distances
All speakers contain magnets which may cause interference
with instruments on your boat. The size of the magnet used in
the speaker affects how much interference the speaker may
cause.
Interference can cause deviations and variations in the readings
of sensitive navigational equipment, such as magnetic
compasses. These deviations can cause inaccuracies or offsets
in the readings, but will not harm the equipment. To alleviate the
deviations, adjust the compass for the deviation following the
manufacturer's instructions or move the speaker away from the
navigational equipment. After moving a source of interference,
you may need to recalibrate the compass.
If you are navigating solely by a magnetic compass, use
extreme caution to place the speaker far enough away from the
compass to avoid causing deviations in the readings.
To avoid deviations to navigational equipment, position the
speakers so they are separated from the navigational equipment
by at least the distance listed in the table below.
Direction
from
Speaker
4" Speakers 6.5" Speakers 7.7" Speakers
À185 cm (6 ft. 1 in.) 250 cm (8 ft. 2 in.) 275 cm (9 ft.)
Á185 cm (6 ft. 1 in.) 245 cm (8 ft.) 275 cm (9 ft.)
Â255 cm (8 ft. 5 in.) 310 cm
(10 ft. 2 in.)
400 cm (33 ft.
4 in.)
Ã185 cm (6 ft. 1 in.) 255 cm (8 ft. 4 in.) 275 cm (9 ft.)
Ä185 cm (6 ft. 1 in.) 230 cm (7 ft. 6 in.) 275 cm (9 ft.)
Å230 cm (7 ft. 7 in.) 280 cm (9 ft. 2 in.) 385 cm (12 ft.
7 in.)
Thiele Small Parameters
You can use the Thiele Small (T/S) parameters when designing
custom enclosures for your speakers.
NOTE: Thiele/Small parameters may vary between samples,
based on the environment and how much the speaker has been
used. These values are intended as a guide to help with
enclosure design.
T/S Parameter 4 in.
Speakers
6.5 in.
Speakers
7.7 in.
Speakers
Electrical Q factor (Qes) 1.80 1.05 0.7
Mechanical Q factor
(Qms)
4.40 4.80 3.6
Total Q factor (Qts) 1.28 0.86 0.59
Resonance frequency
(Fs)
128 82 72
Equivalent air load
(Vas)
1.6 7.6 10.4
Installation Instructions 5

Printing a Mounting Template
NOTICE
It is not recommended that you print a mounting template on your own. Use the template that came in the product box.
If you do print the template, you must follow these instructions for printing a mounting template precisely. To print large templates,
you need large enough paper and printer. Failure to have the correct sized paper and printer, or a failure to follow these instructions,
may result in an incorrectly sized template and therefore an incorrect cutout (too large or too small) on the mounting surface of your
boat.
1 Select File > Print.
➋
➌
➍
➎
➊
2 Select None for Page Scaling ➊.
3 Ensure the check mark is next to Auto-Rotate and Center ➋.
4 Drag the arrow ➌ to the right, to view page 2 in the window below.
4 Verify that the paper size is larger than the template ➍.
In this example, the paper is not larger than the template.
5 If the paper size is not large enough, select Properties ➎and select a Page Size that is larger than the template.
NOTICE
Fusion is not responsible for any damages or expenses resulting from a miscut mounting surface arising from a failure to follow
these instructions.

© 2018 Garmin Ltd. or its subsidiaries
October 2018 Printed in China 190-02481-06_0A
150 mm
6”
Check Dimensions Before Cutting
Ø 162 mm
(6
3
/
8
in.)
176 mm
(6
5
/
8
in.)
XS Series
7.7" Speakers

®
Important Safety and Product Information........................................................................................................................................ 2
Informations importantes sur le produit et la sécurité....................................................................................................................... 3
Informazioni importanti sulla sicurezza e sul prodotto...................................................................................................................... 4
Wichtige Sicherheits- und Produktinformationen.............................................................................................................................. 4
Información importante sobre el producto y tu seguridad.................................................................................................................5
Informações importantes sobre segurança e o produto................................................................................................................... 6
Belangrijke veiligheids- en productinformatie................................................................................................................................... 7
© 2014–2016 Garmin Ltd. or its subsidiaries
June 2016 Printed in China 190-00720-54_0D

Important Safety and Product Information
WARNING
Failure to heed the following warnings could result in an accident resulting in death or serious injury.
Marine Operation Warnings
•You are responsible for the safe and prudent operation of your vessel. This device does not relieve you from the
responsibility of safely operating your vessel. Avoid navigational hazards and never leave the helm unattended.
• Always be prepared to promptly regain control of the vessel. Use caution near hazards in the water, such as docks, pilings
and other vessels.
Hearing Damage Warning
Listening to the stereo at high volume can cause damage to your hearing.
Product Environmental Programs
Information about the Garmin® product recycling program and WEEE, RoHS, REACH, and other compliance programs can be
found at www.garmin.com/aboutGarmin/environment.
Declaration of Conformity
Hereby, Garmin declares that this product is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC. To view the full Declaration of Conformity, go to www.fusionentertainment.com.
Software License Agreement
BY USING THE DEVICE, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING
SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY.
Garmin Ltd. and its subsidiaries ("Garmin") grant you a limited license to use the software embedded in this device (the
"Software") in binary executable form in the normal operation of the product. Title, ownership rights, and intellectual property
rights in and to the Software remain in Garmin and/or its third-party providers.
You acknowledge that the Software is the property of Garmin and/or its third-party providers and is protected under the United
States of America copyright laws and international copyright treaties. You further acknowledge that the structure, organization,
and code of the Software, for which source code is not provided, are valuable trade secrets of Garmin and/or its third-party
providers and that the Software in source code form remains a valuable trade secret of Garmin and/or its third-party providers.
You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the
Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the
Software to any country in violation of the export control laws of the United States of America or the export control laws of any
other applicable country.
Limited 3-Year Marine Consumer Warranty
Garmin New Zealand Limited, trading as FUSION® Entertainment (‘FUSION’), warrants that this FUSION Marine product is
free from defects in material and workmanship, according to the following terms and conditions:
• The limited warranty for the FUSION product purchased extends to 36 months beginning on the date of purchase of the
product.
• The limited warranty extends only to consumers who purchase the product in one of the countries (or areas) set forth on
www.fusionentertainment.com. The limited warranty is only valid in FUSION’s intended country (or area) of sale of the
product.
• During the limited warranty period, FUSION or its authorised service network will repair or replace (at FUSION’s discretion),
any defective product or parts thereof with new and return the product to the consumer in working condition. No charge will
be made to the consumer for either parts or labour in repairing or replacing the product. All replaced parts and cosmetic
parts should be free of defects at the time of shipment and, therefore shall not be covered under these limited warranty
terms.
• Repaired product will be warranted for the balance of the original warranty period or for ninety (90) days from the date of
repair, whichever is longer.
• All warranty claims must be accompanied with a copy of this warranty card, and a copy of proof of purchase.
The consumer shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable:
• The product has been subject to: abnormal use, abnormal conditions, improper storage, unauthorised modifications,
unauthorised connections, unauthorised repair including but not limited to use of unauthorised spare parts in repairs,
misuse, neglect, abuse, accident, alteration, improper installation, acts of God, spill of foods or liquids, maladjustment of
customer controls or other acts which are beyond the reasonable control of FUSION, including deficiencies in consumable
parts such as fuses, and breakage or damage to antennae unless caused directly by defects in materials or workmanship,
and normal wear and tear of the product.
• FUSION was not notified by the consumer of the alleged defect or malfunction of the product during the applicable limited
warranty period.
• The product serial number or the accessory date code has been removed, defaced or altered.
• The product was used with or connected to an accessory not supplied by FUSION or fit for use with FUSION product, or
used in a manner other than its intended use.
If a problem develops during the limited warranty period, the consumer should take the following step-by-step procedure:
1The consumer shall return the product to any authorised FUSION dealer in authorised sales countries for repair or
replacement processing. FUSION assumes no freight or shipping responsibility for returning goods to an authorised
FUSION dealer, or return freight from an authorised dealer to the consumer submitting the warranty claim.
2The consumer shall be charged for any parts or labour charges not covered by this limited warranty. The consumer shall be
responsible for expenses related to removal and reinstallation of the product.
3If the product is returned to FUSION after the expiration of the warranty period, FUSION’s normal service policies shall
apply and the consumer will be charged accordingly.
The benefits conferred by this warranty apply to the extent that they are not superseded by any other rights and remedies
available under any applicable legislation that cannot be excluded. In jurisdictions where implied or legal warranties may be
excluded, any implied or legal warranty is hereby excluded and the foregoing warranty is the purchaser’s sole and exclusive
remedy and is in lieu of all other warranties, express or implied.
• Some states in America do not allow the exclusion or limitation of consequential damages, so the above limitation and
exclusion may not apply to you. This warranty gives you specific legal rights which may vary from state to state.
• FUSION neither assumes nor authorises any authorised service centre or any person or entity to assume for it any other
obligation or liability beyond that which is expressly provided for in this warranty.
• All warranty information, product features and specifications are subject to change without notice.
Limited 3-Year Marine Consumer Warranty for Australian Consumers
Garmin Australasia, 30 Clay Place, Eastern Creek, NSW 2766, Australia.
EMAIL: [email protected] PHONE: [phone]
THE FUSION PROMISE OF QUALITY LIMITED 3-YEAR CONSUMER WARRANTY
This warranty is given in addition to other rights and remedies available to the consumer under Australian Consumer Law. In
addition to the FUSION Warranty, our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for any others reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Garmin New Zealand Limited, trading as FUSION Entertainment (‘FUSION’), warrants this FUSION Product including,
Speaker, Subwoofer, Amplifier, Head Unit, or genuine FUSION Accessory ‘product’ is free from defects in materials and
workmanship, in accordance with the following terms and conditions:
• The limited warranty for the FUSION product purchased is only available for (36) months after the date of purchase.
• The limited warranty extends only to the original consumer of the product and may not be assigned or transferred to any
other person or consumer without FUSION’s prior written consent being provided.
• During the limited warranty period, FUSION or its authorised service network will repair or replace any defective or faulty
product or parts at its own cost.
• Repaired or replaced product will be warranted for the balance of the original warranty period or for ninety (90) days after
the date of repair, whichever is longer.
• All warranty claims must be notified to FUSION or its authorised Dealer in writing during the warranty period accompanied
with a copy of this warranty card, proof of purchase date and the product with an intact and unaltered serial number or
accessory date code.
This warranty will not apply if:
The consumer causes the Product to be of unacceptable quality or fails to take steps to prevent the product from becoming of
unacceptable quality and/or it is damaged by abnormal use. Examples of goods becoming of unacceptable quality or of
abnormal use by the consumer include:
• Storage of product under improper conditions.
• Exposure to excessive moisture or dampness.
• Exposure to excessive temperature extremes or other adverse environmental conditions.
2