GABOR FM-4265 User manual

FM-4265 / FIXED
WALL MOUNT
For 42”- 65”Flat Panel Screens
User Manual

2 Welcome
Thank you for choosing Gabor’s fixed flat panel screen wall mount.
This heavy-duty wall mount has been engineered to provide your
42”-65” flatscreen monitor with sturdy, long-lasting support that
can be relied upon for years of viewing enjoyment.
With an impressive lineup of versatile mounting brackets
possessing various functionalities - along with a resilient, user-
friendly mounting method that simplifies the installation process
- Gabor’s reputation for providing quality viewing solutions and long-
lasting dependability is readily apparent...from every angle.
Thank you for
choosing Gabor.

3Welcome

4 Specifications / Tools Required / Contents
Product Specifications
• For Mounting 42”-65”
Flat Panel Screens
On Wooden Studs &
Concrete Walls
• Vesa Mounting
Pattern
Max. 800 × 400
• Maximum Load
Capacity
132lbs / 60kg
• Product Dimensions
35" × 25" × 1"
Product Contents
Tools Required For Installation
1. Power Drill
2. Phillips Screwdriver
3. Scissors
4. Socket Wrench
Supplied Parts & Hardware
A M4 Lock Washer
B M4 × 12 Bolt
C M4 × 30 Bolt
D M5 Lock Washer
E M5 × 12 Bolt
F M5 × 30 Bolt
G M6 Lock Washer
H M6 × 12 Bolt
I M6 × 35 Bolt
J M8 Lock Washer
K M8 × 16 Bolt
L M8 × 25 Bolt
M M8 × 40 Bolt
N M6 Spacer
O M8 Spacer
P M6 Flat Washer
Q Long Bolt
R M8 Flat Washer
S Wall Anchor

5
Wall Mount Brackets
Contents
J×4
K×4
N×4
O×4
P×4
Q×6
O×6
R×
L×4
O×4
M×4
O×6 S
H×4
I×4
G×4
E×4
F×4
D×4 A×4
B ×4
C ×4
Washer/Bolt/Anchor/Spacer
M5M4 M8M6

6 Installation Instructions
Installation Instructions
STEP 1:
Installing Dual Mounting
Brackets On Rear Of
Flatscreen
• Begin by aligning both
brackets on rear of
flatscreen device, while
ensuring that the
screen is resting on a
non-scratch surface.
The appropriate bolts
and washers should be
selected by measuring
the height, size and
position of holes on rear
of flatscreen device, and
determining which bolts
and washers fit best.
This may vary according
to specific brand, make
and model of flatscreen
device.
• Use the shortest
configuration of bolts,
washers and spacers for
a secure fit. Spacers may
or may not be required
depending on curvature
of flat screen device and
rear dimensions.
• Ensure that brackets
are in proper position
by confirming that
rectangular-shaped
safety locking/unlocking
rod mechanisms are
facing downwards and
toward each other;
align both brackets by
positioning them at equal
heights and secure bolts
tightly.
• Note that bolts must
be hand-fastened into
holes with a screwdriver
or socket wrench to
avoid overtightening and
possible damage.

7Installation Instructions
TOP
TOP
BOTTOM
BOTTOM

8
For Display
With Flat Back:
Install bracket directly
to flatscreen device using
only bolts and washers
provided; align bolt with
proper sized hole on
washer. (Fig.1)
For Display
With Curved Backs &
Recessed Mountings:
Install appropriate sized
spacer between bracket
and flatscreen device;
then fasten securely with
bolts and washers. (Fig.2)
Hardware Configurations
Installation Instructions
• Upon final installation
completion, you can use
scissors to trim length of
safety locking/unlocking
rods so they remain
hidden behind flatscreen
device, but only after
completing step 4.
(Fig.1) (Fig.2)
TOP
BOTTOM

9
STEP 2:
Positioning Mount
Correctly On Wall
• The optimal height to
position a flatscreen
device is by mounting it
at eye-level of viewer.
This can be accomplished
in one of two ways:
• Measure distance from
seating area to viewing
area to determine proper
placement. The ideal
position should place
the center of the panel
(where the diagonals
meet) as close as possible
to eye-level.
• For a simpler calculation,
cut a piece of sturdy
cardboard that’s
approximately the same
size as flatscreen device
and tape to wall; gaze at
cardboard to determine
if it is at a comfortable
level; reposition the
cardboard until it is
sitting at a perfect height
and mark location of
cardboard on wall with a
pencil.
Installation Instructions
15°
Viewing
Angle
Eyelevel
Height

10
STEP 3:
Installing Mount
Directly On Wall
• After confirming height
positioning is appropriate
by marking wall with a
pencil, hold wall mount
firmly against wall and
use pencil to mark exact
location of drill holes,
using built-in bubble
level to ensure a proper
balance; then remove wall
mount and pre-drill holes.
Wall-Type Mounting Details
Mounting To Wood Studs
Under Sheetrock Wall:
Pre-drill holes according
to markings on wall with a
3mm drill bit; be sure pre-
drilled holes are at least
30mm deep; use provided
hardware to attach wall
mount.
Mounting To Solid
Concrete Wall:
Pre-drill holes according
to markings on wall with
a 12.7mm drill bit; be sure
pre-drilled holes are at
least 60mm deep; use
appropriate wall anchors
to attach wall mount
(please verify that included
anchors are appropriate).
Installation Instructions
12.7mm
12.7mm

11
• Hold wall mount securely
and begin inserting
bolts into appropriate
pre-drilled holes; use
a minimum of 2 bolts
(or preferably 3 if wall
location permits) on
upper section and 2
bolts on lower section,
while using appropriate
anchors or washers.
Installation Instructions

12
STEP 4:
Hanging Flatscreen
Device On Wall Mount
• With mounting brackets
fastened to rear of
flatscreen device, lift
entire flatscreen display
over wall mount and
- with the flatscreen
positioned above the
mount - hook upper
section of brackets onto
top part of wall mount.
• Gently lower flatscreen
panel downwards; push
lower section of brackets
into place, allowing built-
in latches to grip bottom
of wall mount.
• Verify that both upper
and lower sections are
fastened securely.
• Note that rods can be
disengaged to remove
flatscreen device by
simply pulling them down
and lifting the device
outwards.
Installation Instructions

13Installation Instructions

14 Safety Warnings
Safety Warnings
1Do not use this product for any
flat panel screen device other than
what it is intended for; the exact
specifications, size parameters and
weight limits are found both on the
product box and in the instruction
manual
2It is strongly recommended that this
product be installed by a qualified
professional or installation contractor;
Gabor takes no responsibility for
any product damage or personal
injury resulting from mishandling,
incorrect mounting, faulty assembly
or improper use of this product
3This product has been designed
specifically for mounting directly
on wooden studs or concrete
walls; depending on wall type and
material, the use of additional
appropriate mounting hardware and/
or accessories such as heavy-duty
anchors may be required
4The supplied mounting hardware is
not intended for use on metal studs
or cinderblock walls, and may not be
appropriate for old or weak walls;
it is best to consult with a qualified
professional to determine whether
your walls are capable of supporting
this bracket
5Product must always be mounted
directly to center of wooden wall
studs or on a solid concrete wall
to properly support the weight of
the device; the wall may require
reinforcement prior to mounting
(i.e. metal studs; plaster on lath; or
irregular spacing of studs), which
should be determined by a qualified
professional
6Do not mount device on structures
that may be affected by vibrations or
noticeable impacts; do not install near
heater, fireplace or any other source
of direct heat energy
7It is recommended that at least 2
people should perform the installation
process to prevent injury from
mishandling or dropping of the
product and/or flatscreen device;
proper safety gear and tools must be
utilized at all times when installing
product
8When installing this product, be sure
to refer to mounting instructions
detailed in this manual; failure to
abide by mounting instructions may
void product warranty
9This product may contain small parts
which can possibly pose a choking
hazard; keep out of reach of children
and pets
10 Excessive exposure to liquids may
damage the finish of this product;
when cleaning this product, use only
a mild detergent solution and quickly
wipe dry with a soft cloth

15Customer Support / Warranty
Customer
Support
For more information or
to arrange service, visit
www.madebygabor.com
or call Customer Service
at 212-594-2353.
Product warranty is provided by
the Gradus Group.
www.gradusgroup.com
Gabor is a registered trademark
of the Gradus Group.
© 2018 Gradus Group LLC.
All Rights Reserved.
GG5
ONE-YEAR LIMITED WARRANTY
This GABOR product is warranted to the original purchaser to be free from defects in
materials and workmanship under normal consumer use for a period of one (1) year
from the original purchase date or thirty (30) days after replacement, whichever
occurs later. The warranty provider’s responsibility with respect to this limited
warranty shall be limited solely to repair or replacement, at the provider’s discretion,
of any product that fails during normal use of this product in its intended manner and
in its intended environment. Inoperability of the product or part(s) shall be determined
by the warranty provider. If the product has been discontinued, the warranty provider
reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect,
accident, alteration, abuse, improper installation or maintenance. EXCEPT
AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY
EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal
rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Gabor Customer Service Department
to obtain a return merchandise authorization (“RMA”) number, and return the
defective product to Gabor along with the RMA number and proof of purchase.
Shipment of the defective product is at the purchaser’s own risk and expense.

WWW.MADEBYGABOR.COM