Gaia Baby Complete Sleep + Mini Cot User manual

IMPORTANT: Please read
carefully and retain for
future reference
Complete Sleep+mini cot
Assembly instructions
Maxi cot
0 to 3 year +
mini cot
0 to 1 year
Toddler
bed
3 to 4 year +
First
bed
4 to 5 year +

2
Mini cot / Maxi cot / Toddler bed / First bed
safety information
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
INSTRUCTIONS FOR SAFE USE
• WARNING:Be aware of the risk of open fires and other sources of
strong heat, such as electric bar fires, gas fires, etc. in the near vicinity
of the cot.
• WARNING: Do not use the cot/bed if any part is broken, torn or missing
and use only spare parts approved by Gaia baby.
• WARNING:Do not leave anything in the cot or place the cot next to
another product which could provide a foothold or present a danger of
suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
• WARNING:Do not use more than one maress in the cot.
• WARNING: When converted to a child’s bed, do not place this bed near
heat sources, windows and other furniture.
• WARNING: To prevent falls, the maress base of this cot should be
adjusted to the lowest position before the child can sit up unaided.
• Recommend maresses sizes:
Mini cot: 92.5cm long x 65cm wide 10cm depth.
Maxi Cot: 135cm long x 65cm wide x 10cm depth
Toddler bed: 1350mm long x 650mm wide x 100mm depth.
First bed: 135cm long x 65cm wide x 10cm depth.
• The line engraved on the cot side indicates the maximum thickness of a
maress that can be used with this cot when the bed base is in the top
position.
• The thickness of the maress chosen shall be such that the internal
height (surface of the maress to the upper edge of the cot frame)
is at least 500mm in the lowest position of the bed base and at least
200mm in the highest position of the bed base.
• Children are likely to play, bounce, jump and climb on beds, therefore
the child’s bed should not be placed too close to other furniture or
windows, and should be placed either tight to any wall or have a gap of
300mm between the wall and the side of the bed.
• The maress should be no more than 30mm shorter or narrower than
the internal length or width of the cot.
• Please ensure that all fiings are tightened properly before use.
Fiings should be checked and tightened regularly every 2 to 3 weeks.
• Your cot and bed may be cleaned with a damp cloth. Never use bleach
or abrasives cleaning agents as this will damaged the surface.
• To prevent injury from falls, once the child is able to climb out of the
cot, it should no longer be used for that child. You should now convert
to either the Toddler bed or First bed.
• This cot bed is intended for children aged from birth to 4 years
approximately.
• When converted to a child’s bed, this cot bed conforms to BS
8509:2008 + A1 2011.

3
Toddler bed
Age range: 3 to 4 years +
Assembly: Pages 22 to 23
Mini cot
Age range: 0 to 1 year
Assembly: Pages 6 to 13
Maxi cot
Age range: 0 to 3 years +
Assembly: Pages 13 to 21
First bed
Age range: 4 to 5 years +
Assembly: Pages 24 to 25

4
30 mm
20 mm
50 mm
300mm
Mini cot Fittings Mini cot ComponentsTools
C x 6 Dx 6
G x 8
Ax 8
Allen key
Supplied
Cross head screwdriver
Not supplied
Ex 16
B x 32
Fx 8
IMPORTANT
PLEASE READ CAREFULLY
Keep all fiings not used
in a safe place away from
young children for future
use.
Please ensure that bolts
& screws are not over-
tightened. Failure to do
this will result in potential
damage.
When assembling, do not
fully tighten the bolts
on the cot/crib sides
until the product is fully
assembled. This will help
with assembly.
1x 4 2x 4
2a
2b
3Box 2 4Box 1
5x 4
3b 4b
3a 4a
8x 2
7x 2
9x 2
10 x 2

5
1
Ex 12
2a 2b
2a 2b
1
11
Mini cot assembly CRIB end information
Mini cot 1
4b
3b
4a
3a
Note: Crib ends 3a & 3b
are in BOX  and Crib ends
4a & 4b are in BOX .
IMPORTANT: Please
ensure that parts 3a & 3b
and 4a & 4b are always
kept together and used as
a pair. Failure to do so will
result in potential damage
and miss alignment.

6
Cx 6
3b
4b
Fx 8
Bx 8
Bx 4 5
5
3a
4a
Mini cot 2
Mini cot 4
Mini cot 3

Ex 2
5
7
Bx 4
3a
3b
4a
4b
Dx 6
7
Using barrel nuts
The barrel nuts come in two
parts the barrel and the grub
screw. Insert the grub screw
into the end of the barrel and
turn clockwise.
Before inserting the barrel
nuts into the holes in the
component, ensure the end of
the barrel nut stud will fit into
the barrel nut.
If the stud does not fit turn
the grub screw anti-clockwise
until the stud can be inserted.
Grub
screw
Barrel nut
stud
Barrel nut Mini cot 5
Mini cot 6 Mini cot 7

8
Ex 2
Gx 4
Gx 2
Bx 2
Bx 1
Gx 2
Bx 1
Mini cot 9Mini cot 8
Mini cot 10 Mini cot 11

5
Bx 12
59
8
8
9
Ex 4
9
Mini cot 12 Top Base position
bottom Base position
Top base position
Use the top base position for
newborn babies.
Once the baby can push its
self upwards on its hands or
starts to pull itself up using
the side of the cot, you MUST
fit the cot base in the boom
position.
IMPORTANT: When fiing
the top base position rails,
ensure the pilot holes in the
rails are facing upwards.
Boom base position
Use the boom base position
for when your baby can push
itself up on its hands or starts
to pull itself up on the sides of
the cot.
IMPORTANT: The boom base
position is the safest position
for the cot base
Mini cot 13
Top base
position

10
10
10
Ax 8
Assembly complete
Mini cot 15
Top base
position
Mini cot 14
Top base position
Mini cot 16
Boom base
position

Bx 12
11
Mini cot 18
Boom base
position
Mini cot 17
Boom base
position
Mini cot 19
Boom base
position
Assembly complete

12
30 mm
20 mm
50 mm
300mm
790mm
420mm
Maxi cot Fittings Maxi cot ComponentsTools
G x 10
I x 6
H x 4
Ax 12
Allen key
Supplied
Cross head screwdriver
Not supplied
Ex 16
B x 36
Fx 10
IMPORTANT
PLEASE READ CAREFULLY
Keep all fiings not used
in a safe place away from
young children for future
use.
Please ensure that bolts
& screws are not over-
tightened. Failure to do
this will result in potential
damage.
When assembling, do not
fully tighten the bolts
on the cot/crib sides
until the product is fully
assembled. This will help
with assembly.
5x 4
9x 2
8x 2
11 x 2
10 x 2
12 x 2
13 x 2
15 x 1
14 x 2
1x 4 2x 4
2a
2b
3Box 2 4Box 1
3b 4b
3a 4a

13
Dismantle the mini cot
Crib ends
Maxi cot Assembly
IMPORTANT: Do not dismantle the
two cot ends as they are required
when building the cot.
Note: If you have not constructed
the cot ends, please refer to the
instructions on pages 4, 5, 6 &
7 of this instruction booklet to
assemble them.
IMPORTANT: Aer dismantling the Mini cot, keep the components shown
in grey to build the cot and store the other components in a safe place.

14
Bx 4
12
13
13
12
Gx 2
Bx 1
Bx 1
Gx 2
Gx 2
Bx 1
Maxi cot 1 Maxi cot 2
Maxi cot 4
Maxi cot 3

15
Hx 4
Fx 2
14
14
Gx 1
14
Ex 2
Maxi cot 6
Maxi cot 8
Maxi cot 5
Maxi cot 7

Bx 6
9
11
8
Bx 4
55
16
Bottom Base position
Top base position
Use the top base position for
newborn babies.
Once the baby can push its
self upwards on its hands or
starts to pull itself up using
the side of the cot, you MUST
fit the cot base in the boom
position.
IMPORTANT: When fiing
the top base position rails,
ensure the pilot holes in the
rails are facing upwards.
Bottom Base position
Boom base position
Use the boom base position
for when your baby can push
itself up on its hands or starts
to pull itself up on the sides of
the cot.
IMPORTANT: The boom base
position is the safest position
for the cot base
Maxi cot 9
Top base
position
Maxi cot 10
Top base
position

17
Bx 6
9
11
8
Gx 1
14
Ex 2
15
10
10
Maxi cot 13
Top base
position
Maxi cot 11
Top base
position
Maxi cot 12
Top base
position
Maxi cot 14
Top base
position

Bx 16
18
Maxi cot 17
Boom base
position
Maxi cot 16
Boom base
position
Maxi cot 15
Top base
position
Assembly complete

19
Ax 12
Maxi cot 18
Boom base position
Maxi cot 19
Boom base
position
Assembly complete

20
Ex 2
Toddler bed conversion Toddler bed 1
Toddler bed 2