GAL A X Y AUDIO Quick Start Guide
Included Components
1. PA6S x1
3. SA-1 Stand Adapter x1
2. IEC Power Cable x1
Setup
2.1. 4.
4. Quick Start Guide x1
3.
Connect power cable to PA6S, connect
other end to a power outlet.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mic, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6S. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6S.
5
Connect a female XLR to the Thru
output to feed the channel’s XLR input
to another device.
1
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
6
Flip the power switch on.
3
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
4
EQ controls - Low/Mid/Hi: To increase the
low, mid, and high frequencies, turn the
appropriate tone control clockwise. To
decrease, turn counter-clockwise.
5
Reduce the Input Levels if the Clip LED
comes on.
6
Max. level is reached when the yellow
“Comp” light only flashes at peak levels.
If the light is on constantly, turn the level
controls down to avoid damage to the
PA6S.
2
1
Ensure that both channels have their
levels lowered by turning counter-
clockwise.
Stand Mounting (Optional)
1
Attach the SA-1 to the mic stand, then
Lift the PA6S over the stand, align it up
with the hole.
2
Bring the PA6S down onto the stand
gently until secure.
Operation
The Pre Out provides a Line Level mix
of both channels.
7
GAL A X Y AUDIO Quick Start Guide
Included Components
1. PA6S x1
3. SA-1 Stand Adapter x1
2. IEC Power Cable x1
Setup
2.1. 4.
4. Quick Start Guide x1
3.
Connect power cable to PA6S, connect
other end to a power outlet.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mic, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6S. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6S.
5
Connect a female XLR to the Thru
output to feed the channel’s XLR input
to another device.
1
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
6
Flip the power switch on.
3
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
4
EQ controls - Low/Mid/Hi: To increase the
low, mid, and high frequencies, turn the
appropriate tone control clockwise. To
decrease, turn counter-clockwise.
5
Reduce the Input Levels if the Clip LED
comes on.
6
Max. level is reached when the yellow
“Comp” light only flashes at peak levels.
If the light is on constantly, turn the level
controls down to avoid damage to the
PA6S.
2
1
Ensure that both channels have their
levels lowered by turning counter-
clockwise.
Stand Mounting (Optional)
1
Attach the SA-1 to the mic stand, then
Lift the PA6S over the stand, align it up
with the hole.
2
Bring the PA6S down onto the stand
gently until secure.
Operation
The Pre Out provides a Line Level mix
of both channels.
7
