Galvin CliniLever Series Instruction sheet

Version 1, 24 August 2018, Page 1 of 4
CliniLever® Hospital Swivel
Wall Outlets
PRODUCT CODES:
- 85007 - 85035 - 85050
- 85057 - 85060 - 85064
SPECIFICATIONS
 The CliniLever® product range is primarily used for hand washing applications in medical facilities,
hospitals, aged care facilities, schools and in-home care.
 CliniLever® products provide state of the art features to comply with the latest healthcare guidelines.
 Convenient swivel design.
 Robust construction for long life.
 Low maintenance.
 Laminar flow.
 Finished in bright chrome plate for easy cleaning and durability.
IMPORTANT: All CliniLever® healthcare taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet 1/2” BSP - Female
Outlet Laminar Flow
Headwork N/A
Working Pressure Range (kPa) Min 50
Max 500
Working Temperature Range (°C) Min 5
Max 80
Nominal Flow Rate (LPM) 7
Finish Chrome
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
 Power drill
 Spanner or adjustable crescent
 Thread tape

Version 1, 24 August 2018, Page 2 of 4
PRE-INSTALLATION
MOUNTING DETAILS
Wall Spud − Wall spud must be ½” BSP MI and protrude from the
finished wall by no more than 15mm
Note: In some situations, a male thread connection on the tap
may be more suited. If so, please contact us on 1300 514 074
Note: Before installation, all lines must be flushed. We recommend
that a line strainer be installed prior to taps to eliminate any foreign
material.
85007
85035
85050
85057
85060
85064

Version 1, 24 August 2018, Page 3 of 4
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation
instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water
and/or electrical supply conditions must also comply to the applicable national and/or state standards. Failing
to comply with these provisions shall void the product warranty and may affect the performance of the
product.
1. Fit tap assembly
 Remove the spout from the wall elbow
using a hex key. This is to enable easy
installation and prevent the spout being
damaged
2. Connect
 Place the wall flange over the elbow. Fit the elbow
to the protruding wall spud. We recommend
using thread tape or an equivalent to ensure the
connection does not leak.
 Ensure spout connection is pointing up (vertical).
3. Refit the spout
 Refit the spout to the elbow. Tighten
the grub screw using a hex key.
Note: Do not overtighten grub screw.
Ensure spout swivels freely once installed.
4. Testing
 Turn on the water supply and test for leaks.

Version 1, 24 August 2018, Page 4 of 4
TROUBLESHOOTING
PROBLEM CAUSE RECTIFICATION
Inconsistent flow Blocked aerator
Blocked top assembly
Remove aerator and clean
Remove top assembly and clean
Water is not flowing from the tap Water is turned off Turn on the water
Continuous flow Top assembly loose or
internally obstructed or
damaged
Remove top assembly, clean with
water and replace if required
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.