GAMCO BCS-1 User manual

Your unit can be installed to meet ADA regulations when and where applicable. Refer to Federal Register, Volume
56, No 144 28 CFR Part 36.
You are responsible for the safe operation of this unit.
INSTALLATION AND OPERATION INSTRUCTIONS
GAMCO WALL-MOUNTED BCS-1 AND BCS-2 Please Note:
To assure proper installation, it is suggested that a qualied person or carpenter install the Gamco Baby
Changing Station. Gamco Commercial Restroom Accessories will not be responsible if the station is not
installed properly
Gamco Baby Changing Stations have been tested to hold a substantial static load. The unit must be
attached to a permanent wall that is capable of holding a substantial load. The maximum recommended
total weight for this baby changing station (including baby and parcel bag) is 60 lbs. Excessive weight may
cause a hazardous or unstable condition to exist.
Using Restraint System
To fasten the waist restraint strap, place strap around child’s midsection, and push spring tabs into buckle
until both spring tabs lock in place with an audible “click”. Straps can be adjusted to make strap tighter or
looser as required.
Inspection Criteria:
A properly maintained baby changing station:
– Opens and closes smoothly
– Has both ends of a functioning, non-frayed strap: buckle clicks when closed and strap is attached to unit at both
ends.
– Provides a clean, convenient place for customers to attend to their children.
OPERATING INSTRUCTIONS
ASTM F 2285-04
WARNING: Never leave child unattended.
WARNING: Avoid serious injury from
falling or sliding out. Always use restraint system.
WARNING: Designed for Infants Only.
Age up to 3.5 years and weighing less than 50
lbs. Keep one hand on the child at all times.
Parcels or accessory items, or both, placed on
the unit may cause the unit to become unstable.
EN 12221:2008
WARNING: Do not leave the child unattended.
All assembly ttings shall always be correctly tightened and
checked regularly.
Be aware of the risk of open re and other sources of strong heat,
such as electric bar res, gas res, etc. in the near vicinity of the
changing unit.
The changing unit is intended up to a maximum weight of 15 kg.
Do not use changing unit if any parts are broken or missing. A
changing pad is not required for this product.
Additional or replacement parts shall only be obtained from the
manfacturer or distributor.
Unit should be cleaned once or more daily with a clean nylon brush
and spray disinfectant.
MATERIALS SUPPLIED: TOOLS WHICH MAY BE NEEDED FOR INSTALLATION:
Measuring Tape
Gloves
Level
Stud nder
Pencil
Drill
Phillips screwdriver
7/32" Drill Bit. (masonry)
1/8" Drill Bit. (regular)
1/2" Drill Bit. (reg & masonry)
(4) 1/4" x 3" Panhead wood screws
(4) 1/4" Flat washers

HORIZONTAL BABY CHANGING STATION
GAMCO WALL-MOUNTED BCS-1 AND BCS-2
INSTALLATION INSTRUCTIONS
Step 1.
Remove changing station from the shipping container and check for any freight damage. Identify the
best location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken
the operating clearance into consideration.
Step 2.
Based upon the type of wall on which you will be mounting the station, determine the best method of
mounting. You may have left over hardware when you are  nished with installation.
Step 3.
The horizontal unit has four mounting holes provided in the back wall of the unit. The four holes are
positioned on a 32" (813mm) stud center.
If possible, locate the wood or metal studs for fastening the changing station in the desired location.
If the walls do not have studs on center as outlined, make sure at least one side of the unit is installed
into the stud. Use toggles (may have to purchase) for holes on the other side.
Step 4.
Find the stud where you will be attaching the left side of the changing station to the wall. Measure up
from the fl oor 44" (1118mm), at the center of the stud and mark the wall. Mark holes using a level and
measuring tape to make sure holes are precisely positioned. Hold unit in place to check. Use a 1/8"
drill bit to make pilot holes and the four ¼" x 3" panhead screws with washers (supplied) to attach the
unit to the wall studs. This will place the bottom of the station 26-1/2" (673mm) from the fl oor and the
top of the bed at 33" (838mm) from the fl oor.
If the wall surface is masonry or tile over wood studs, use a 7/32" masonry drill bit for the pilot hole
until you hit the stud. Change bit to 1/8" regular drill bit. Use the four 1/4" x 3" panhead wood screws
with washers (supplied).
If the wall has wood studs that are not on
32" (813mm) centers, has metal studs or an
underlying surface of concrete block, drill with
a 1/2" (12mm) masonry bit. (You may have
to purchase toggles before installing.) You
must allow a minimum of inside wall space for
toggles to turn depending on toggles used.
Insert and tighten toggles.
Bobrick Customer Service New York Division
Phone: [phone] • Fax: [phone]
Bobrick Customer Service Los Angeles Division
Phone: [phone] • Fax: [phone]
or email [email protected]
Gamco Commercial Restroom Accessories: A Division of Bobrick, One Gamco Place, Durant, OK 74701-1910
For Customer Service Bobrick New York Division Phone: [phone] • Fax: [phone]
For Customer Service Bobrick Los Angeles Division Phone: [phone] • Fax: [phone]
© 2012 by Gamco Commercial Restroom Accessories P/N 1027 Issued 8/2012 Printed in U.S.A.