Gared Holdings SGSQPT Guide

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
1 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
SGSQPT
SOCCER GOAL MODELS INCLUDED IN THIS INSTALLATION INSTRUCTIONS ARE:
SGSQ612PT, SGSQ618PT, SGSQ721PT, AND SGSQ824PT
WARNING
Portable or Moveable Soccer Goals can fall over causing serious injury or death.
Anchors must be properly installed and used on all portable or moveable soccer
goals at ALL times.
GOAL WIDTH
GOAL
HEIGHT

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
2 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
Table of Contents
Section Page No.
Introduction/Liability Disclamer 2
Parts Checklist 3
Goal Assembly 4-12
Storage 13
Maintenance 14
Thank you for your purchase of the SGSQPT Soccer Goal. To ensure that our equipment will provide
years of use to you, we are including this installation, operation, and maintenance guide. This guide
will provide information on the proper assembly and installation methods, operating procedures, and
preventative maintenance of your soccer goal.
Please note that a Bill of Materials is being included with this guide. Please check that all of the
parts called out on the Bill of Materials are present prior to beginning assembly. Please do not
substitute for factory parts. Please contact the PSS or Gared Sports customer service department
and allow them to determine if substitute parts are acceptable.
It is recommended that an individual who has been properly trained perform assembly and set up of
the Soccer Goal. No one under the age of 18 should attempt assembly or set up of the unit, unless
properly supervised.
To prevent normal wear and tear from shortening the life of the unit, preventative maintenance
inspections and repairs should be performed at least once per year. If the units are subject to high
or unusual usage, inspections should be scheduled to occur more frequently. If items are found to
be nonconforming, replacements can be ordered from Gared Sports or one of our authorized dealers.
When contacting PSS or Gared Sports, please have information regarding the dealer/installer who
sold the unit, the name of the project, and any applicable warranty information.
Introduction/Liability Discalimers
Before proceeding with assembly, read all instruction and assembly proceedures. make sure all
parts have been received and are not damaged.

8’ x 24’ 7’ x 21’ 6.5’ x 18.5’ 6.5’ x 12’
Item Description Qty SGSQ824PT SGSQ721PT SGSQ618PT SGSQ612PT
1 Net 1 SN824-4W SN721-3W SN618-3W SN612-3W
2 Top Rail 1 655755815 655755812 655755809 655755861
3 Side Rail 2 655755816 655755813 655755810 655755810
4 Backstay Bent 2 656202400 656202403 656202406 656202406
5 Backstay Straight 2 656202401 626202404 656202407 656202407
6 Backstay Brace 1 656202402 656202405 656202408 656202411
7 Connecting Tube 2 655755202
8 Backstay Mtg Brkt 4 656202416
9 Clamp Plate, Narrow 4 656202106
10 Brace Clamp (pair) 2 651653590
11 Ground Anchor 4 651652570
12 Vinyl End 4" Square 2 101653829
13 Carriage Bolt 5/16 x 2.5 2 501-5-18-40SS
14 Hex Bolt, 5/16x0.875 8 502-5-18-14SS
15 Hex Bolt, 3/8x1.5 8 502-6-16-24SS
16 Hex Bolt, 3/8x2.75 4 502-6-16-44SS
17 Button Head Bolt 5/16x2.38 2 509-5-18-38SS
18 Lock Nut, 5/16 4 545-5-18SS
19 Lock Nut, 3/8 4 545-6-16SS
20 Flat Washer, 5/16 6 561-5SS
21 Flat Washer, 3/8 16 561-6SS
22 Lock Washer, 5/16 8 562-5SS
23 Lock Washer, 3/8 8 562-6SS
24 Net Clips 40 651652567
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
(Common to all goals this series)
TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
3 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
Parts Checklist
Verify all parts listed on the packing list are present prior to installation.
Soccer Goal frame components
Check the chart for the proper parts that match the Goal P/N received.

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
4 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
6
(Master Illustration)
Use the above illustration to identify the main parts of your SGSQPT soccer goal.
*NOTE:
Balloon numbers throughout this manual will match the Item numbers in the Parts Checklist.
1
3
2
4
3
5
4
11
5

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
5 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
2
Goal Frame Assembly
*Use the following step by step instructions to assemble your SGSQPT soccer goal.
Step 1:
Attach a Backstay Mounting Bracket (8) to each end of the Top Rail (2) as shown in the
following illustration. Use 5/16” x 7/8” bolts (14), and 5/16” lock washers (22) to attach the
bracket. The clamp plate (9) fits into the slot in the extrusion as shown. Slide the bracket up and
hand tighten the bolts. Position is not important at this point. Go to step 2.
9
8
22
14
SLIDE THE CLAMP PLATE UP INTO
THE SLOT IN THE EXTRUSION

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
6 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
2
7
Step 2:
Next attach the Side Rails. Position the Connecting Tube (7) between the Side Rail and Top Rail.
Align the four holes. Attach the Side Rail (3) with 3/8” x 1-3/4” bolts (15), 3/8” flat washers (21),
and 3/8” lock washers (23). Use the illustration below as a guide. When everything is aligned,
securely tighten the bolts.
3
8
21
23
15

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
7 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
Step 3:
Before connecting the backstay components to the goal, assemble the two backstay
components together. Attach the straight backstay pipe (5) to the bent backstay pipe (4)
by inserting the straight section into the lower bent section and aligning the holes. Install
the 5/16 x2-3/8" button head bolt (17) and 5/16" flat washer (20) through the hole. Add a
5/16" flat washer (20) and 5/16" locknut (18). Tighten the nut securely. Repeat for the
second backstay assembly.
5
4
18
20
20
17

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
8 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
12
Step 4:
Now attach the lower Backstay Mounting Bracket (8) as shown in the illustration below. Slide the
Clamp Plate (9) up into the slot of the extrusion. Use the same hardware as the top bracket. Then
place the Square Vinyl End cap (12) onto the end of the side rail. The backstay bracket will overlap
the end cap as shown. Mount the bottom end of the Backstay Pipe (5) to the bracket using two 3/8”
flat washers (21), a 3/8” x 2-3/4” bolt (16), and a 3/8” nylon lock nut (19) to attach the backstay. The
bottom side of the backstay pipe should be even with the bottom of the vinyl end cap so that the goal
sits level.
BRACKET OVERLAPS
THE VINYL ENDCAP
BOTTOM OF BACKSTAY SHOULD BE
EVEN WITH BOTTOM OF ENDCAP
9
19
21
22
14
5
8
21
16

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
9 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
Step 5:
Attach the top end of the Backstay Pipe (4) to the top of the Backstay Mounting Bracket (8) as shown
in the illustration below. Use the same hardware as the lower bracket. The height of the backstay pipe
will determine the final position of the top mounting bracket. When all parts are aligned, securely
tighten the bracket bolts (14).
4
8
21
16
19
21 14

TM
GARED
PERFORMANCE
SPORTS SYSTEMS
Gared Holdings, LLC
9200 E. 146th St.
Noblesville, IN 46060
FILE LOC.
SHT. NO. PART NO. REV
PORTABLE SQUARE SOCCER GOALS
10 OF 14
651752318 A
Q:\Inventor Files\
DATE
12/26/2017
Installation and Assembly Instructions
Step 6:
Attach the Backstay Brace Pipe (6) near the back of the two side backstay pipes. (see the following
illustration). Use two Brace Clamp halves (10) to attach each end of the brace pipe. Insert a 5/16” x
2-1/2” carriage bolt (13) from the bottom as shown. Secure with a 5/16” flat washer (20) and a 5/16”
nylon lock nut (18). Make sure the brace pipe is perpendicular to the backstay pipe and tighten the
nuts securely.
4
5
6
10
10
18
20
13