Gasmate GRHM User manual

02896 05/13 M
Important: Retain these instructions for future use.
Gasmate®is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.au
Aber – Hamilton, N.Z. www.gasmate.co.nz
Wall Mounted BBQ
Rangehood
GRHM & GRHL
GRHM
GRHL

3
2
USE, CARE AND
INSTALLATION GUIDE
Read all instructions before installing
and operating this appliance
IMPORTANT SAFETY NOTICE
WARNING
Installation
The installation in this manual is intended
for qualied installers, service technicians or
persons with similar qualied backgrounds.
DO NOT attempt to install this appliance
yourself. Injury could result from installing
the unit due to lack of appropriate electrical
and technical background.
Always ensure this range hood is installed as per
the requirements noted in AS/NZS 3000:2007
There shall be adequate ventilation of the
room when the range hood is used at the
same time as appliances burning gas or other
fuels (not applicable to appliances that only
discharge the air back in to the room;
CAUTION: Accessible parts may
become hot when used with
cooking appliances.
• There is a risk if cleaning is not carried out
in accordance with the instructions
• Do not ambé under the range hood
• The air must not be discharged into an existing
ue that is used for exhausting fumes from
appliances burning gas or other fuels
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• All electrical wiring must be properly
installed, insulated and grounded. It is
not recommended to use old duct work it
should be replaced if necessary to avoid the
possibility of a grease re. Check all joints
on duct work to ensure proper connection all
joints should be properly taped.
• Do not attempt to modify this appliance as this
could cause injury and will void your warranty
• Underside surfaces can become hot during
use. Do Not Touch.
Operations
Read all instructions in this manual before
operating the appliance. Save these
instructions for future reference.
Always leave safety grills and lters
in place. Without these components,
operating blowers could catch on to hair,
ngers and loose clothing.
NEVER dispose cigarette ashes, ignitable
substances or any foreign objects in to
the blowers.
NEVER leave cooking area unattended.
When frying, oil in the pan can easily
overheat and catch re. The risk of self-
combustion is higher when the oil has been
used several times.
Cleaning
The saturation of greasy residue in the
blowers and lters may cause increased
ammability. Keep unit clean and free of
grease and residue build-up at all times to
prevent possible res.
Filters must be cleaned periodically and be
free from accumulation of cooking residue
(see cleaning instruction). Old and worn
lters must be replaced immediately.
Do not operate blowers when lters are
removed. Never disassemble parts to clean
without proper instructions. Disassembly is
recommended to be performed by qualied
personnel only. Call our service centre for
removal instructions.
SITRO GROUP AUSTRALIA Declines all
responsibility in the event of failure to
observe the instructions given here for
installation, maintenance and suitable use
of the product.
SITRO GROUP AUSTRALIA further declines
all responsibility for injury due to negligence
and the warranty of the unit automatically
expires due to improper maintenance.

3
INSTALLATION
MOUNTING HEIGHTS AND CLEARANCE
The minimum distance between the supporting
surface for the cooking vessels on the hob and
the lowest part of the range hood. When the
range hood is located above a gas appliance,
this distance shall be at least 120cm. If the
instructions for installation for the gas hob
specify a greater distance, this has to be taken
into account.
Minimum mount height above cooking surface
should be no lower than 1200mm (120cm)
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
hoods mounted too high will be hard to reach and
Maximum ceiling clearance 2700mm at 1200
mm hood mounting height (depending on
model used)
Minimum duct size:
GRHM - Round 2x150mm diameter
GRHL - Round 3 x 150mm diameter
Flexible ducts are supplied for convenience,
always use rigid type metal ducts if available to
min 1200mm
915mm
max 2700mm
Extension available
Electrical Data
IMPORTANT
the mains power supply for Australia / New Zealand and meets the requirements of Australian
Standards. This range hood must be connected to a supply voltage that is equal to that stated on
the rating label. If the mains power connection plug or power cord becomes damaged it must be
replaced with a complete assembly that is identical to the original, and this must be replaced by an
authorised service centre. Always follow the Australian / New Zealand requirements for connection
Flexible Duct Material (Supplied), Notes for
Installation.
1) Never combine the ducts, always flue all ducts
individually to the atmosphere and ensure a
cap and flashing are used on all ducts.
GRHM – 2 motors and 2 ducts
GRHL – 3 motors and 3 ducts
2) When using screws and silver tape to join the
flexible duct to the rangehood, ensure that
the screws and silver tape do not interfere
with the operation of the “butterfly” baffles.
NOTE: Check “butterfly” baffles operation
before completing the duct installation.
3) Ensure that the flexible ducts are as
straight as possible with no excess curves, as
the excess curves will reduce the airflow by at
least 50%.
4) Always ensure that the rangehood is level in
all directions and an un-level rangehood will
reduce air flow by at least 30%.
Note: Incorrect installation is not covered
under warranty.

4
DUCTING
WARNING: FIRE
NEVER Exhaust air or terminate duct work into
spaces between walls, crawl spaces, ceilings ,
attics or garages. All exhaust must be ducted to
the atmosphere.
Use Metal duct work only.
Fasten all connections with sheet metal screws
duct tape.
Side wall cap with
gravity damper
Roof Pitch with
Flashing & Cap
Ceiling or crawl space
Side wall cap with
gravity damper
Flexible Duct Material (Supplied), Notes for
Installation.
1) Never combine the ducts, always flue all ducts
individually to the atmosphere and ensure a
cap and flashing are used on all ducts.
GRHM – 2 motors and 2 ducts
GRHL – 3 motors and 3 ducts
2) When using screws and silver tape to join the
flexible duct to the rangehood, ensure that the
screws and silver tape do not interfere with
the operation of the “butterfly” baffles.
NOTE: Check “butterfly” baffles operation
before completing the duct installation.
3) Ensure that the flexible ducts are as straight
as possible with no excess curves, as the
excess curves will reduce the airflow by at
least 50%.
4) Always ensure that the rangehood is level in
all directions and an un-level rangehood will
reduce air flow by at least 30%.
Note: Incorrect installation is not covered
under warranty.

5
4
INSTALLATION
Mounting the Range Hood
1. Measure from cooking surface to hood bottom
(1200mm min) level and mark line A.
2. Plum and mark centre line “C/L”.
3. Measure between bottom of hood to
mounting hole and add this dimension line
above line A.
4. Mark mounting spread from C/L “Y: (measure
between two mounting holes).
5. Fasten anchors to wall (see below)
as advised by the manufacturer, ensuring they
are suitable for the range hood weight
6. Fasten screws or nuts do not fasten all the way.
7. Hang hood and tighten (g A).
Mounting the Duct Cover
Locate and attach the duct cover as required
using self tapping screws no longer than 6mm
(not supplied)
Warning: Failure to install the screws or
xing device in accordance with these
instructions may result in electrical hazards.
1. Centre and attach duct cover mount bracket on
wall below ceiling.
2. Fasten telescopic duct covers onto hood
and bracket.
Connecting to Power Supply
After the range hood is securely installed, route
the power cord safely away from all sharp
corners and possible entrapments to the power
point then plug in and turn on.
Duct Cover Bracket
C/L
B
A
C/L
g.A
Min 1200mm
EZ anchor or Dyna-Bolt
Ensure adequate mounting hardware is used
(if unsure ask your hardware supplier).

7
6
MAINTENANCE
CLEANING
Surface Maintenance
Clean periodically with hot soapy water and
a clean cotton cloth. Do not use corrosive or
abrasive detergent or steel wool/scouring pads
which will scratch and damage the surfaces.
For heavier deposits, use a liquid degreaser.
After cleaning, you may use non-abrasive stainless
steel polish/cleaners to polish and buff the stainless
lustre. Always rub lightly, with a clean cotton cloth
and with the grain.
Filters
The Metal Filters tted by the factory are intended
to lter out residue and grease from cooking.
They are required to be kept clean and should be
cleaned after every 30 hours of use or more often if
required.
Remove and clean by hand or in dishwasher.
Spray with a degreasing detergent and leave to
soak if heavily soiled. Dry lters and re-install
before using hood.
Replacing lters
Should lters wear out due to age and prolonged
use, replace with following part number:
Product ID: Bafe Filter
Description: Stainless Steel Filter
Available at http://www.gbi.com.au
OPERATION
The light is switched on by pressing the
corresponding button.
Each exhaust fan has three speeds which can be
selected by pressing the required button. A blue
L.E.D light indicates the selected function.
Pressing the selected button again will turn off or
alternatively press the off button,
OFF HIGH MED
FAN
LOW LIGHT

7
TECHNICAL INFORMATION
MODEL GRHM GRHL
Voltage 220-240V AC 220-240V AC
Frequency 50Hz 50Hz
Motor wattage 2 x 1000W 3 x 1000W
Lamp 2 x 12V-1.8W 3 x 12V-1.8W
Lamp type L.E.D L.E.D
Extraction capacity 2000m3/hr 3000m3/hr
Noise Level ≤650Dba ≤650Dba
WARRANTY TERMS AND CONDITIONS
This warranty is not transferable to a subsequent purchaser if the product is sold by the original purchaser
during the warranty period.
If a warranty fault appears within the warranty period, S.G.A. reserves the right to replace or repair the product.
In the event that S.G.A. chooses to replace the product, this original warranty will expire at the original date.
If the product includes various accessories or components, only the defective accessory or component will be
replaced or repaired.
S.G.A. reserves the right to replace defective parts of the product with parts and components of similar quality,
grade and composition where an identical part or component is not available.
Products presented for repair may be replaced by refurbished products of the same type rather than being
repaired. Refurbished parts may be used to repair the products.
To make a warranty claim, rst contact S.G.A's Customer Service Line on the contact number below.
The purchase receipt for this product is to be retained and must be presented if making claim under the terms of
this S.G.A. warranty.
Warranty repairs are free of charge, provided the product is delivered to our Service Department at 33-35 Lionel
Road, Mt Waverley, Victoria, 3149 or to one of our Authorised Service Agents.
If a warranty fault is found the freight cost will be credited to the owner.
If no fault is found the product will be returned and any costs associated with the service will be charged to the
owner.
Products sent freight forward will not be accepted.
In most cases the defective accessory or component only will need to be returned. The product or part of the
product being returned must be adequately protected in a box.
S.G.A. will not be responsible for any in-transit loss or damage.
‘Continued on page 8’

8
For any queries or assistance call
Customer Service
(Australia Only)
1300 174 876
Hours of operation:
Monday to Friday 8.30am - 5.30pm EST
Do not return to place of purchase.
Keep your purchase receipt, this will be required to
make any claims under the 2 year warranty.
Gasmate®is a registered trademark of:
Sitro Group Australia Pty Ltd www.gasmate.com.au
Aber Ltd - Hamilton, N.Z www.gasmate.co.nz
This warranty does not apply to any defect, deterioration, loss, injury or damage occasioned by or as a result
of misuse or abuse, negligent handling or storage, normal wear and tear or if the product has not been
installed and used in accordance with S.G.A.'s instructions, recommendations and specications or if the
product has been subjected to abnormal conditions. The warranty does not apply to blockages caused by
insects or living organisms, as well as non-operating buttery baes or incorrectly installed ducts.
The warranty is void if there is evidence of the product being tampered with by unauthorised persons.
The warranty does not extend to installation or disconnection costs.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. The benets of this warranty are in
addition to any rights and remedies imposed by Australian State and Federal legislation that cannot be
excluded.
Gas Products Approved For Outdoor Use Only
For warranty claims, service, spare parts or products information in Australia, please call SITRO GROUP
AUSTRALIA Pty Ltd on the Customer Service Line 1300 174 876
A receipt or proof of purchase is required and must be kept for your records.
CONTACT DETAILS
Sitro Group Australia Pty Ltd
33-35 Lionel Road, Mt. Waverley
Victoria 3149, Australia.
Tel [phone]
Fax [phone]
[e-mail]