GE RAP02 User manual

1
Parts Included:
1. Dual Hose Conversion Baffles (2)
2. Intake Hose Adapter to AC
3. Intake Hose Adapter to Window Kit
4. Intake Hose
5. Exhaust Hose Insulation
6. Dual Hose Window Panel
31-5000578 Rev. 1 03-21 GEA
Installation Instructions
for your new
Before you begin - Read these instructions completely and carefully.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
RAP02 Dual Hose
Conversion Kit
Tools Needed
• Phillips head screwdriver • Small hand saw - if trimming of the
window expansion panels is required
5.
1.
6.
4.
2.3.

2
IMPORTANT SAFETY INSTRUCTIONS
WARNING To reduce the risk of fire, electrical
shock, injury to persons, or damage when using the air
conditioner, follow basic precautions, including the
following:
• Read all of the instructions before using this appliance.
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Do not operate the air conditioner if it has a damaged
cord or plug, if it is not working properly, or if it has been
damaged or dropped.
• The air conditioner should be serviced only by qualified
service personnel. Call an authorized service company
for examination, repair, or adjustment.
• Disconnect power before servicing.
• Disconnect power before cleaning.
NOTE: Turning off power by pressing the Power button
does NOT disconnect the appliance from the power
supply.
• Do not install or use the air conditioner in any area
where the atmosphere contains combustible gases
or where the atmosphere is contaminated. Avoid any
chemicals coming in contact with your air conditioner.
• Do not store anything directly on top of the air
conditioner.
• Use two or more people to move and install air
conditioner.
• Never operate the air conditioner without the filters in
place.
• Do not use the air conditioner near a bathtub, shower or
wash basin or other wet area.
• Do not use means to accelerate the defrosting process
or to clean, other than those recommended by the
manufacturer.
• The appliance shall be stored in a room without
continuously operating ignition sources (for example:
open flames, an operating gas appliance or an
operating electric heater.
• Do not pierce or burn refrigerant tubing. Be aware that
refrigerants may not contain an odor.
• Keep ventilation openings clear of obstruction.
• When handling, installing, and operating the appliance,
care should be taken to avoid damage to the refrigerant
tubing.
• Do not drill holes in the unit.
• Maintenance, cleaning, and service should only be
performed by technicians properly trained and qualified
in the use of flammable refrigerants.
• GE Appliances does not support any servicing of the air
conditioner.
• Dispose of air conditioner in accordance with Federal
and Local Regulations. Flammable refrigerants require
special disposal procedures. Contact your local
authorities for the environmentally safe disposal of your
air conditioner.
WARNING
Risk of Fire or Explosion. This unit contains flammable refrigerant.
Additional safety precautions must be followed.
Safety
Units are recommended to operate at conditions of 104 F Outdoor and 80 F indoor and below.

3
Converting GE Portable Air Conditioner to Dual Hose Configuration
Installation Instructions
STEP 1: Unplug or disconnect power
WARNING
Electrical Shock Hazard
• Disconnect power before servicing
• Replace all parts and panels before operating
• Failure to do so can result in death or electric shock
STEP 2: Determine Location Requirements
• Place the air conditioner on a flat, level surface in a
location that is at least 20” (51 cm) from any wall.
NOTE: A minimum clearance of 20” (51 cm) from
the air conditioner to the wall must be maintained to
ensure proper airflow.
• Keep the air conditioner free of any obstructions
such as drapes, curtains, blinds, etc.
• The hoses should be free of any obstructions.
• Do not place the air conditioner on an unstable
or raised surface because it could fall and cause
damage or injury.
•
Do not place the air conditioner in direct sunlight
or near a heat source such as baseboard heaters,
stoves, etc.
• The window panel can be installed in a window with
a minimum 24” (61 cm) to a maximum 52” (132 cm)
opening.
STEP 3: Installing the Exhaust Hose
Insulating Sleeve
If you previously installed your GE Portable Air
Conditioner, you will need to remove the Window Kit
from the window and then remove the Exhaust Hose
Adapter from the Window Kit. Next, remove the hose
from the back of the AC and slide the fabric insulation
over the hose, starting from the end you just removed
from the back of you AC. It will be easier if you fully
extend the hose before sliding the insulation over the
hose. You can then re-attach the hose to the back of
the AC.
If you have not installed your Portable AC yet, using
the parts that came with your Portable Air Conditioner,
please follow the instructions to assemble the 2 adapters
onto the exhaust hose to make up the exhaust hose
assembly (step 2 of the Installation Instructions
that came with your Portable AC). Slide the fabric
insulation over the hose, starting from the end with
the round AC to hose adapter. It will be easier if you
fully extend the hose before sliding the insulation over
the hose. You can now assemble the exhaust hose
assembly onto the back of the Air Conditioner

4
STEP 5: Assemble Intake Hose Assembly
and Mount to back of Unit
Using the parts that were included in the Dual Hose
Conversion Kit, extend the intake hose approximately
4” from each end. Screw the adapters onto the ends of
the hose, turning clockwise until they are secure. Insert
the round adapter into the intake vent on the baffle you
assembled onto the AC in the previous step and turn
counter-clockwise to secure it.
STEP 6: Install Intake and Exhaust Hose
Adapters to Dual Hose Window Panel
1. Hold the Dual Hose
Window Panel so
that the L-shaped
edges of the panel
are facing you.
2. Insert the exhaust adapter
into the right side opening
in the window kit and slide
to lock it in place.
3. From the opposite side,
insert one of the flat
tipped screws through the
hole in the Window Panel
into the adapter to lock it
in place.
4. Repeat the above instructions for the intake adapter
using the left side opening.
Installation Instructions
STEP 7:
Complete the installation by continuing from Step 4 on
page 13 of the Use & Care manual that came with your
Portable Air Conditioner. For some window openings,
you may need to cut the expansion panels.
STEP 4: Attach the Dual Hose Conversion
Baffle to the Back of the Air Conditioner
• From the back of your Air Conditioner, remove the two
Philips head screws holding the Intake Grille to the AC
• Remove the Air Intake Grille and filter
• Replace the Grille with the matching Dual Hose
Conversion Baffle, securing it with the two Philips head
screws.
• Use the Small Dual Hose Conversion Baffle for these
models:
APCD07JALW, APWD07JASG, APCD08JALW,
APCD08JASW, APSD08JASG, APWD08JAWW
• Use the Large Dual Hose Conversion Baffle for these
models:
APCD10JALW, APCD10JASG, APWD10JASG,
APWD10JAWG, APXD10JAWB
Printed in the United States

131-5000578 Rev. 1 03-21 GEA
Instrucciones de Instalación
para su nuevo
Antes de comenzar – lea estas instrucciones completamente y de forma detenida.
IMPORTANTE- CUMPLA CON TODOS LOS CÓDIGOS Y ORDENANZAS GUBERNAMENTALES.
Nota para el Instalador – Asegúrese de entregar estas instrucciones al Consumidor.
Nota para el Consumidor – Guarde estas instrucciones con su Manual del Propietario para referencia futura.
Kit de Conversión con
Manguera Doble RAP02
Herramientas Necesarias (no incluido)
• Un destornillador de estrella • Sierra manual pequeña – si es
necesario recortar los paneles de
expansión de la ventana.
PARTES INCLUIDAS:
1. Deflectores de Conversión de la Manguera Doble (2)
2. Adaptador de la Manguera de Entrada al Acondicionador de Aire
3. Adaptador de la Manguera de Entrada al Kit de Ventana
4. Manguera de Entrada
5. Aislante de la Manguera de Salida
6. Panel de Ventana de la Manguera Doble
5.
1.
6.
4.
2.3.

2
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
ADVERTENCIA Parareducirelriesgode
incendio,choqueeléctrico,lesionesapersonasodañosal
utilizarelacondicionadordeaire,sigaprecauciones
básicas,incluyendolassiguientes:
• Leatodaslasinstruccionesantesdeusareste
electrodoméstico.
• Conecteauncontactodepareddeconexiónatierrade3
terminales.
• Noquiteelterminaldeconexiónatierra.
• Nouseunadaptador.
• Nouseuncableeléctricodeextensión.
• Nopongaafuncionarelacondicionadordeairesitiene
uncableoenchufedañado,sinofuncionacorrectamente
osisehadañadoocaído.
• Elacondicionadordeairesolodebeserreparadopor
personaldeserviciocompetente.Llamealacompañía
deserviciotécnicoautorizadaparasuinspección,
reparaciónoajuste.
• Desconecteelsuministrodeenergíaantesdedarle
serviciotécnico.
• Desconecteelsuministrodeenergíaantesdelimpiarlo..
NOTA: SiapagalaunidadpresionandoelbotónPower
(Encendido),estoNOdesconectaelelectrodoméstico
delsuministrodeenergía.
• Noinstaleniutiliceelacondicionadordeaireenáreas
dondelaatmósferacontengagasescombustibles
odondelaatmósferaestécontaminada.Eviteque
cualquierproductoquímicoentreencontactoconel
acondicionadordeaire.
• Noalmacenenadadirectamenteencimadel
acondicionadordeaire.
• Conlaayudadedosomáspersonas,muevaeinstaleel
acondicionadordeaire.
• Nuncahagafuncionarelacondicionadordeairesilos
filtrosdeairenoestáncolocadosensulugar.
• Noutiliceelacondicionadodeairecercadeunatina,
duchaolavaboniotrazonahúmeda.
• A fin de acelerar el proceso de descongelación o
para limpiar, no use ningún método que no sea el
recomendado por el fabricante.
• Este electrodoméstico deberá ser guardado en una
sala donde no haya fuentes de encendido continuas
(por ejemplo: llamas abiertas, un electrodoméstico
que funcione a gas o un calefactor que funcione a
electricidad).
• No perfore ni queme el tubo refrigerante. Tenga
presente que los refrigerantes no deben tener olor.
• Mantenga las aberturas de la ventilación libres de
obstrucciones.
• Al mover, instalar y operar el electrodoméstico, se
deberá tener cuidado para evitar dañar la tubería del
refrigerante.
• No realice perforaciones en la unidad.
• El mantenimiento, la limpieza y el servicio técnico sólo
deberán ser realizados por técnicos adecuadamente
entrenados y calificados en el uso de refrigerantes
inflamables.
• GE no suministra servicio técnico para el
acondicionador de aire.
• Descarte el electrodoméstico de acuerdo con las
Regulaciones Federales y Locales. Los refrigerantes
inflamables requieren procedimientos de descarte
específicos. A fin de descartar su acondicionador de
aire de forma ambientalmente segura, comuníquese
con las autoridades locales.
Riesgo de Incendio o Explosión. Esta unidad contiene refrigerante inflamable.
Se deben seguir las precauciones adicionales de seguridad.
ADVERTENCIA

3
Instrucciones de instalación
PASO 1: Desenchufe o desconecte la
corriente. WARNING
Riesgo de descarga eléctrica
• Desconecte el cable de corriente antes de realizar el
servicio técnico.
• Reemplace todas las piezas y paneles antes del uso.
• Si no se cumple con esto, se podrán producir descargas
eléctricas o la muerte.
PASO 2: Determine los Requisitos de
Ubicación
• Coloque el acondicionador de aire sobre una supercie
plana y nivelada en una ubicación que esté al menos
a 20” (51 cm) de la pared.
NOTA: La distancia recomendada de la ventana para
un rendimiento óptimo es de 20 “(51 cm).
• Mantenga el acondicionador de aire libre de
obstrucciones como cortinas con pliegues, cortinas,
persianas, etc.
• Las mangueras deberán estar libres de cualquier
obstrucción.
• No coloque el acondicionador de aire en una supercie
inestable o elevada, ya que podría caerse y provocar
daños o lesiones.
• No exponga el acondicionador de aire a la luz directa
del sol o cerca una fuente de calor como zócalos
radiantes, estufas, etc.
• El panel de la ventana puede instalarse en una
ventana con una abertura mínima de 24” (61 cm)
hasta un máximo de 52” (132 cm).
Conversión del Acondicionador de Aire Portátil de GE Appliances a una
Configuración con Manguera Doble
PASO 3: Instalación de la Manga Aislante de
la Manguera de Salida
Si de forma previa instaló su Acondicionador de Aire
Portátil de GE Appliances, será necesario retirar el Kit
de Ventana de esta última y luego retirar el Adaptador
de la Manguera de Salida del Kit de Ventana. Luego,
retire la manguera de la parte trasera del acondicionador
de aire y deslice el aislante de tela sobre la manguera,
comenzando desde el extremo que acaba de retirar de
la parte trasera del acondicionador de aire. Será más
fácil si extiende la manguera completamente antes de
deslizar el aislante sobre la manguera. Luego podrá
volver a adherir la manguera a la parte trasera del
acondicionador de aire.
Si aún no instaló el acondicionador de aire portátil
utilizando las piezas incluidas con su acondicionador
de aire portátil, por favor siga estas instrucciones para
ensamblar los 2 adaptadores a la manguera de salida,
a fin de realizar el ensamble de la manguera de salida
(paso 2 de las instrucciones de instalación). Deslice el
aislante de tela sobre la manguera, comenzando desde
el extremo redondo del acondicionador de aire hasta el
adaptador de la manguera. Será más fácil si extiende la
manguera completamente antes de deslizar el aislante
sobre la manguera. Ahora puede instalar el ensamble
de la manguera de salida sobre la parte trasera del
acondicionador de aire.

4
PASO 5: Instale el Ensamble de la manguera
de entrada y monte el mismo sobre la parte
trasera de la unidad
Usando las piezas incluidas con el kit de conversión
de la manguera doble, extienda la manguera de
entrada aproximadamente 4” desde cada extremo.
Atornille los adaptadores sobre los extremos de la
manguera, girando en sentido horario hasta que queden
asegurados. Inserte el
adaptador circular en la
ventilación de la entrada
del deflector que ensambló
sobre el acondicionador
de aire en el paso previo y
gire en dirección antihoraria
para asegurarlo.
Instrucciones de instalación
Impreso en Estados Unidos
PASO 4: Adhiera el Deflector de Conversión
de la Manguera Doble sobre la Parte
Trasera del Acondicionador de Aire
• Desde la parte trasera del acondicionador de aire,
retire los dos tornillos con cabeza Phillips que
sostienen la rejilla de entrada al acondicionador de
aire.
• Retire la rejilla de entrada de aire y el filtro.
• Reemplace la rejilla por el deflector de conversión de
la manguera doble que coincida, asegurando el mismo
con dos tornillos de cabeza Phillips.
• Use el Deflector de Conversión de la Manguera Doble
Pequeño para estos modelos:
APCD07JALW, APWD07JASG, APCD08JALW,
APCD08JASW, APSD08JASG, APWD08JAWW
• Use el Deflector de Conversión de la Manguera Doble
Grande para estos modelos:
APCD10JALW, APCD10JASG, APWD10JASG,
APWD10JAWG, APXD10JAWB
PASO 6: Instale los adaptadores de la
manguera de entrada y salida al panel de la
ventana de la manguera doble
1. Mantenga el panel
de la ventana de
la manguera doble
de modo que los
extremos con forma
de L del panel miren
hacia usted.
2. Inserte el adaptador de
salida sobre la abertura
del lado derecho del kit
de ventana y deslice el
mismo hasta que quede
bloqueado en su posición.
3. Desde el lado opuesto,
inserte uno de los
tornillos con punta
plana a través del
agujero del panel de la
ventana hasta dentro
del adaptador para
bloquearlo en su posición.
4. Repita las instrucciones anteriores del adaptador de
entrada usando la abertura del lado izquierdo..
PASO 7:
Complete la instalación continuando desde el Paso 4 en
la página 13 de su manual de Uso y Cuidado incluido
con su acondicionador de aire portátil. Para algunas
aberturas de ventana es posible que necesite cortar los
paneles extensibles.
Table of contents
Languages:
Other GE Air Conditioner manuals

GE
GE AEM08 Series Operating instructions

GE
GE Zoneline AZ55H12EAB User manual

GE
GE AJCS10DCB Assembly instructions

GE
GE APSA13 Operating instructions

GE
GE AGX08 Operating instructions

GE
GE AKM18DN User instructions

GE
GE AJEM12DCE Original instructions

GE
GE ASV12AL Manual

GE
GE AEL05LX Operating instructions

GE
GE AHM05 User manual
Popular Air Conditioner manuals by other brands

Samsung
Samsung AJ***JNLDCH installation guide

Panasonic
Panasonic S-22MU1E5A installation instructions

Argo
Argo Extreme 9 operating instructions

Lennox
Lennox VRF V22A Series Installation instruction

DURASTAR
DURASTAR DRAL12F1A installation manual

Mitsubishi
Mitsubishi Mr.Slim MSZ-GE12NA operating instructions