Gemini CDX-1200 User manual

SINGLE CD PLAYER
CDX-1200
OPERATING INSTRUCTIONS
INSTRUCCIONES DE OPERACION
MODE D’EMPLOI
OPERATING INSTRUCTIONS
FOR ENGLISH READERS PAGE 2 ~ PAGE 5
FOR SPANISH READERS PAGE 6~ PAGE 9
FOR FRENCH READERS PAGE 10 ~ PAGE 13
FOR GERMAN READERS PAGE 14 ~ PAGE 17

MIXER
15
BACK
16
(NOT INCLUDED)
REAR PANEL OF
5
4
6
18
21 11 13
10
20
9
12
7
14
19
CDX-1200
3
8
17
2
1
3
FRONT

Congratulations on purchasing the Gemini CDX-1200 CD Player.
This state of the art 2U professional CD player is backed by a 1 year
warranty*. Prior to use, we suggest that you carefully read all the instructions.
- Audio CD, CD-R CD-RW compatible
- Anti-shock using RAM buffer memory
- 2 Selectable og modes Pitch Bend/Search
- Instant-start & cue with preview
- Single auto-cue/continuous play modes
- Seamless loop with reloop
- Pitch bend via jog wheel or buttons
- Three mode time selection
- Frame accurate search
- Large blue backlit LCD display
- Coaxial RCA digital output
- Rubber jog wheels with finger grips
- Variable pitch control with a 16% range
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25° C)
Laser Output: Continuous Wave, max. 0.5 mW
1. Do not use this CD player at temperatures below 41°F/5°C or
higher than 95°F/35°C.
2. The apparatus should not be exposed to dripping or splashing,
and no objects filled with liquids such as vases should be
placed on the apparatus.
3. Place the unit in a clean and dry location.
4. Do not place the unit in an unstable location.
5. When disconnecting the power cord from the AC outlet,
always grasp it by the plug. Never pull the power cord.
6. To prevent electric shock, do not remove the cover or the bottom
screws.
7. There are O USER SERVICEABLE PARTS I SIDE. Please
refer to a qualified technician.
8. Do not use chemical solvents to clean the unit.
9. Keep the laser pickup clean by keeping the tray closed.
10. Keep this manual in a safe place for future reference.
INTRODUCTION:
IN THE USA ~ IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT CALL GEMINI
CUSTOMER SERVICE AT: 1 ( 32) 346-0061. DO NOT ATTEMPT TO RETURN THIS EQUIPMENT
TO YOUR DEALER.
CDX-1200
4
FEATURES:
SAFETY SPECIFICATIONS:
PRECAUTIONS:
CONNECTIONS:
1VOLTAGE SELECTIO SWITCH Before plugging the CDX-1200 into any
wall outlet, make sure that the VOLTAGE SELECTIO SWITCH is set to
the proper voltage.
To change this selection unscrew the hard plastic protective top with a
Phillips head screw driver. Then use a flat head screw driver to move
the switch to the proper selection (115V or 230V) .
Do not force or twist the switch. Excessive force may cause damage, if
the switch does not move smoothly, contact a qualified technician.
2POWER After you have properly set the VOLTAGE LI E SELECTOR
SWITCH you may plug in the power cord of the CDX-1200.
LI E OUTPUT JACKS Plug one end of the included RCA cable into
LI E OUTPUT JACKS on the rear panel. Plug the other end of the
RCA connectors into any available line input jacks on your mixer.
If you are connecting the CDX-1200 through a reciever, you can
plug the RCA connectors into the CD or AUX I PUT JACKS on your
reciever. If there are no CD or AUX I PUTS use any line level
(not phono) inputs.
3
4
FUNCTIONS:
POWER: Once you have connected all your cables and made sure
that the VOLTAGE SELECTIO SWITCH is set correctly, you can turn
the CDX-1200 on by pressing the POWER button, pressing the
CDX-1200’s POWER button a second time will turn off the unit.
DISC TRAY: The DISC TRAY is where the CD is held during loading,
unloading and playback, and holds both 12 cm and 8cm CD’s.
(DO OT FORCE THE CD TRAY TO CLOSE EXCESSIVE FORCE WILL
DAMAGE THE CD MECHA ISM, USE THE OPE A D CLOSE BUT-
TO S)
EJECT BUTTO : Pressing the EJECT BUTTO will open or close the
DISC TRAY, unless the CDX-1200 is in play mode, then you must first
stop the side you wich to eject.
JOG WHEEL : In SEARCH MODE the JOG WHEEL can be used to
search forward or bacwards in the music track, as well as for fine
adjustments to a CUE point in PAUSE mode. In PITCH BE D mode the
JOG WHEEL will function the same as the PITCH BE D allowing you
to speed up (FORWARD) or slow down (REWI D) the music clock-
wise bieng (FORWARD) and counter clockwise being (REWI D).
JOG MODE BUTTO : When the JOG MODE BUTTO is illuminated
it indicates the the JOG WHEEL is in SEARCH MODE, and when not
illuminated it indicates that the JOG WHEEL is in PITCH BE D
MODE.
DISPLAY: The DISPLAY shows the track number, pitch value, pitch
bend, single, continue (for continuous play), play/pause modes, fast
forward/reverse modes, loop mode, reloop mode, PGM, repeat
modes, the playback display bar, and three diffirent time displays.
These times displays are TIME ELAPSED on the track, TIME REMAI -
I G on the disc and and TIME REMAI I G on the track. Time is
measured in minutes, seconds and frames.
PGM: Allows you to create a set playlist. To program a set list into
the CDX-1200 memory, begin by stopping the unit from play and
pressing PGM to begin the set list. Select a track by using the track
selection button to scan to the first track to be placed in the set list.
When you have selected the proper track press PGM and the
CDX-1200 will be ready to set your next selection. Repeat the previ-
ous steps until you have completed your playlist, then press play to
begin the set list.
REPEAT: Press the repeat button once to engage 1or repeat the
selected track. Press REPEAT again to engage ALL setting wich will
repeat all the tracks on the CD. Press REPEAT again to disengage
the repeat function
5
6
7
8
9
10
11

CDX-1200
5
FUNCTIONS: (CONTINUED)
12 SI GLE: Pressing the SI GLE button engages SI GLE mode, in this
mode the CDX-1200 will play one song and then stop. Pressing the
SI GLE button again will then activate CO TI UOUS mode causing
the unit to play continuously (after the last track, the unit will return to
the first track of the disc and continue to play).
TIME: The TIME BUTTO switches the time display between three
available sources, these three are TIME ELAPSED on the track, TIME
REMAI I G on the disc and and TIME REMAI I G on the track.
TIME ELAPSED indicates how much time has currently gone by since the
play button was pressed, TIME REMAI G O DISC will count down the
time remaining on the entire disc and TIME REMAI I G O TRACK
counts down the time that is left before the end of the track.
PITCH: Pushing the PITCH button (the button will light up blue) activates
the PITCH CO TROL SLIDE. The pitch or speed of the CD will change
plus or minus 12% depending on the position of the PITCH CO TROL
SLIDER. Push the PITCH button again to deactivate this mode.
PITCH CO TROL SLIDE: Moving the PITCH CO TROL SLIDE
up or down will lower or raise the pitch percentage + or - 12%.
PITCH BE D: Pushing the PITCH BE D BUTTO S will automatically
raise the pitch up to +16% or lower the pitch down to -16% from the
existing pitch setting. Releasing the buttons will return the pitch
to the original pitch setting. You can use this function to match the beat
when mixing from one song to another
LOOP SECTIO : A LOOP repeats the section between the entry point
(I ) and the exit point (OUT). To set a loop while the unit is playing,
start by pressing the I BUTTO (it will light up) and when you reach
the desired end loop point press the OUT BUTTO (it will also light up).
The loop will continue playing until you press the OUT BUTTO again
allowing the music to continue from that point on, to re-engage the loop
you must press the RELOOP BUTTO . When you have released your
loop the OUT BUTTO will turn OFF and the I BUTTO will remain lit
to indicate that your loop is stored in the CDX-1200 memory. Pressing
the I BUTTO again while the unit is playing will erase the previously
saved loop while saving your new loop entry point. Press OUT to exit the
loop and save a new complete loop.
Press RELOOP to return to the beginning of the previously saved loop
from normal play. Press RELOOP repeatedly to cause the loop to stutter.
OTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POI T,
WHILE ALL OTHERS WILL BE SEAMLESS.
PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTO
causes the operation to change from PLAY to PAUSE or from PAUSE
back to PLAY. The PLAY/PAUSE BUTTO remains lit when in PLAY
mode, while it blinks in PAUSE mode.
CUE: While the unit is playing and after the cue point has been
programmed, pressing CUE will cause the CD player to enter the
PAUSE mode (PLAY/PAUSE BUTTO blinks) at the programmed cue
point (the CUE LED is lit). Holding down the CUE button
changes the function to preview , and allows you to stutter start or play
from the programmed CUE POI T Releasing the CUE button will return
the CD to the preset CUE point.
STOP BUTTO : When pressed the STOP BUTTO stops the playback
of the CD player.
13
14
15
16
17
18
19
20
21 TRACK SELECTIO : The TRACK SELECTIO buttons let you select
the track to play. +10 allows you to scan through the track selection
in increments of 10. TRACK SKIP allows you to scan through each
track one at a time.
OTE : O CE YOU HAVE SKIPPED TO A OTHER TRACK, YOU MAY OT GO BACK
TO YOUR PROGRAMMED CUE POI T. YOU MUST BEGI YOUR CUE SELECTIO
OVER AGAI , THE CUE WILL BE PRESET TO THE BEGI I G OF THE EWLEY SE-
LECTED TRACK.
TROUBLESHOOTING:
- If a disc will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
- If the disc turns but there is no sound, check the cable connections,
if they are ok, check your amplifier or reciever.
-If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many cd’s are recorded out of spec and
will skip on most or all CD players. Before sending the unit for repair,
try playing a CD that you are sure plays properly.
SPECIFICATIONS:
GE ERAL:
Type................................................................................Compact Disc Player
Disc Type...................................Standard Compact discs (12 cm & 8 cm)
Time Display......................Track Elapsed, Track Remain, or Total remain
Variable Pitch.......................................± 12% Slider with Resume Switch
Pitch Bend............................................................................± 16% Maximum
Instant Start....................................................................Within 0.03 seconds
Installation...........................................................................................19" each
Dimensions.........Main unit: 19" x 3.5" x 10" (482.6 x 88.9 x 254 mm)
Weight Per Unit..........................................Main unit: 11.35 lbs. (5.14 kg)
AUDIO SECTIO :
Quantization......................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate..............................................................................8 Times
Sampling Frequency..........................................................................44.1 kHz
Frequency Response............................................................20 Hz to 20 kHz
Total Harmonic Distortion...................................................Less Than 0.05%
Signal to Noise Ratio..............................................................................85 dB
Dynamic Range........................................................................................85 dB
Channel Separation.................................................................85 dB (1 KHz)
Output Level...................................................................2.0 +/- 0.2V R.M.S.
Power Supply.......................................................AC 115/230V, 60/50 Hz
SPECIFICATIO S A D DESIG ARE SUBJECT TO CHA GE WITH-
OUT OTICE FOR PURPOSE OF IMPROVEME T.