Genelec 7060B User manual

Quick setup guide
7060B-7070A-7071A
0
+6
+12
+3
-3
-6
-4
0
+6
+12
+3
-3
-6
-4
PHASE
0/-180 DEG
0/-90 DEG
ROLL-OFF
ON
-2 dB
-4 dB
1
1
2
2
3
3
4
4
PHASE
0/-180 DEG
0/-90 DEG
ROLL-OFF
ON
-2 dB
-4 dB
1
1
2
2
3
3
4
4
Bass
Roll-Off
Input
sensitivity
Position
A, B and D:
-2 dB
Suggested Tone Control
settings for a single subwoofer
Position C:
-6 dB
Note
Distance from front wall
Aligning the subwoofer
Subwoofer placement
D
D
AB
10 cm (4)
Main
speaker
110 cm (43)
60 cm (24) 60 cm (24)
10 cm (4) 10 cm (4)
Positioning too far from the wall may
cause a loss in low frequency response
C
1 Positions A and B are recommended.
2 Position C causes a significant bass
boost and may cause asymmetrical
spatial imaging if only one subwoofer is
used.
3 Recommended position for two linked
subwoofers is A+B. Positions C and D
may also work, but may cause loss of LF
when off room center axis.
4 LF mutual coupling causes a 6 dB
bass level increase when using two, 9.5
dB with three and 12 dB with four sub-
woofers.
C
Genelec Document BBAQSLSE001a. Copyright Genelec Oy 10.2006. All data subject to change.

7060B-7070A-7071A
Quick setup guide
Connection to the 6.1 bass management
Phase alignment
REDIRECT
SUM IN MODE
LFE BAND IDTH
120
85 TEST TONE
ON
LFE + 10 dB
REDIRECT
SUM IN MODE
LFE BAND IDTH
120
85 TEST TONE
ON
LFE + 10 dB
REDIRECT
SUM IN MODE
LFE BAND IDTH
120
85 TEST TONE
ON
LFE + 10 dB
LFE reproduced full range LFE reproduced up to 85 Hz LFE reproduced up to 120 Hz
Subwoofer Subwoofer
Subwoofer
85 Hz 85 Hz 120 Hz
1. Switch on the test tone
by setting dip switches 3
and 4 on the left switch
group to on. An 85 Hz
signal should be heard
from the subwoofer and
the monitor connected
to FRONT CENTER
channel.
5. Switch off the test
tone. Be sure to turn off
both switches to disable
the test tone.
Optional
slave subwoofer
SUM IN
input only
REDIRECT
SUM IN MODE
LFE BAND IDTH
120
85 TEST TONE
ON
LFE + 10 dB
ROLL-OFF
-4 dB
-2 dB
ON
PHASE
0/-180 DEG
0/-90 DEG
ROLL-OFF
-4 dB
-2 dB
ON
PHASE
0/-180 DEG
0/-90 DEG
ROLL-OFF
-4 dB
-2 dB
ON
PHASE
0/-180 DEG
0/-90 DEG
REDIRECT
SUM IN MODE
LFE BAND IDTH
120
85 TEST TONE
ON
LFE + 10 dB
2. Toggle the sub-
woofers dip switch 4 on
the right switch group
on and off and set it
to the position which
gives the lowest sound
level at the listening
position.
3. Toggle the sub-
woofers dip switch 3 on
the right switch group
on and off and set it
to the position which
gives the lowest sound
level at the listening
position.
4. Set dip switch 4 to
the opposite setting.
LCR
SL SC SR
LFE
Setting the LFE channel reproduction bandwidth
Center speaker
redirect on
Genelec Document BBAQSLSE001a. Copyright Genelec Oy 10.2006. All data subject to change.
GENELEC