Getnet GR-724W User manual

1
M
Mu ul lt ti i- -L La an ng gu ua ag ge es s Q QI IG G o on n t th he e C CD D
Č
Če es sk ký ý
Českého průvodce rychlou instalací naleznete na
přiloženém CD s ovladači.
D
De eu ut ts sc ch h
Auf der beiliegend Treiber CD finden Sie deutsche
Anleitung zur Schnellinstallation.
E
Es sp pa añ ño ol l
Incluido en el CD el G.R.I. en Español.
F
Fr ra an nç ça ai is s
Veuillez trouver l’français G.I.R ci-joint dans le CD.
I
It ta al li ia an no o
Incluso nel CD il Q.I.G. in Italiano.
M
Ma ag gy ya ar r
A magyar telepítési útmutató megtalálható a
mellékelt CD-n.
N
Ne ed de er rl la an nd ds s
De nederlandse Q.I.G. treft u aan op de bijgesloten
C
P
Po ol ls sk ki i
Skrócona instrukcja instalacji w języku polskim
znajduje sięna załączonej płycie CD.
P
Po or rt tu ug gu uê ês s
Incluído no CD o G.I.R. em Portugues.
Р
Ру ус сс ск ки ий й
Р
Ру ус сс ск ки ий й: : Найдите Q.I.G. на pусскoмязыке на
приложеном CD.
R
Ro om ma an ni ia a
Cd-ul cuprinde Ghid de instalare rapida in limba
romana.
T
Tü ür rk kç çe e
Ürün ile beraber gelen CD içinde Türkçe Hızlı
Kurulum Kılavuzu'nu bulabilirsiniz.
繁/簡體中文 CD 片內含繁體中文及簡體中文快速安裝指南

2
Copyright©by Edimax Technology Co, LTD. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of this Company .
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not this company, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves
the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different
from those shown in this QIG. For more detailed information about this product,
please refer to the User Manual on the CD-ROM. The software and specifications are
subject to change without notice. Please visit our web site www.getnet.com.tw for the
update. All rights reserved including all brand and product names mentioned in this
manual are trademarks and/or registered trademarks of their respective holders .
Linux Open Source Code
Certain Getnet products include software code developed by third parties,
software code is subject to the GNU General Public License ("GPL") or GNU
Lesser General Public License ("LGPL"). Please see the GNU (www.gnu.org)
and LPGL(www.gnu.org) Websites to view the terms of each license.
The GPL Code and LGPL Code used in Getnet products are distributed without
any warranty and are subject to the copyrights of their authors. For details, see
the GPL Code and LGPL Code licenses. You can download the firmware-files at
http://www.getnet.com.tw under "Download" page.

3
1 Product Introduction
Thank you for purchasing Getnet wireless broadband router! This high cost-efficiency
router is the best choice for Small office / Home office users, all computers and
network devices can share a single xDSL / cable modem internet connection at high
speed. Easy install procedures allows any computer users to setup a network
environment in very short time - within minutes, even inexperienced. When the
number of your computers and network-enabled devices grow, you can also expand
the number of network slot by simple attach a hub or switch, to extend the scope of
your network.
You can configure the router by running the Setup Wizard in the CD-ROM provided in
the package. The wizard provides quick setup for the Internet connection, SSID,
wireless security, firmware upgrade and changing router’s password. When you start
the Setup Wizard, you will get the following Welcome screen. Please choose the
language to start with and follow the easy steps in the Wizard. No instruction for the
Setup Wizard is given here.
If you lost the CD-ROM or you prefer the traditional web setup, please follow the
procedures in this Quick Installation Guide to configure the router

4
1-1 Package Contents
Before you starting to use this router, please check if there’s anything missing in the
package, and contact your dealer of purchase to claim for missing items：
□Broadband router (main body, 1 pcs)
□Quick installation guide (1 pcs)
□One CD-ROM (Including the Setup Wizard, Multi-languages Quick Installation
Guide and User Manual)
□12V power adapter (1 pcs)
□Ethernet Cable
□Accessories
1-2 Front Panel
GR-724W
LED Light
Status Description
PWR ON Router is ready
WAN
LNK/ACT
ON WAN is connected
Off WAN is unconnected
Flashing WAN port is sending / receiving data

5
LAN
LNK/ACT
(Port 1-4)
ON LAN port is connected
Off LAN port is unconnected
Flashing LAN port is sending / receiving data
WLAN
ON Wireless network is switched on or WPS mode is on.
Off Wireless LAN is disabled
Flashing Wireless LAN is sending / receiving data
1-3 Back Panel
GR-724W
Item Name Description
Power Power connector, connects to 12V power adapter
ON/OFF Enable / Disable wireless signal
You can not connect the router via wireless adapter,
when you disable the wireless signal.
Reset / WPS Reset the router to factory default settings (clear all
settings) or start WPS function.
(a) Press this button and hold for 20 seconds to clear
all settings.
(b) Press this button for 2 ~ 5 seconds to start WPS
function.
1 - 4 The router’s 4 LAN ports are where you connect your
LAN’s PCs, printer servers, hubs and switches etc.
WAN Wide Area Network (WAN / Internet) port
To improve wireless signal reception, please arrange the antennas as the picture
shown below (horizontal or vertical installation), and place the wireless access point
in open space. Please keep the distance between antennas, if the antennas are too
close to each other, wireless signal reception will be affected.
N
No ot te e: : P Pl le ea as se e r re ef fe er r t to o t th he e Q Qu ui ic ck k I In ns st ta al ll la at ti io on n G Gu ui id de e a an nd d U Us se er r M Ma an nu ua al l i in n t th he e
C
CD D- -R RO OM M f fo or r m mo or re e d de et ta ai il ls s i in nf fo or rm ma at ti io on n o on n I In nt te er rn ne et t c co on nn ne ec ct ti io on n t ty yp pe e a an nd d t to o
c
co
on nf fi ig gu ur re e a al ll l o ot th he er rs s s se et tt ti in ng g. .

6
F
Fe ed de er ra al l C Co om mm mu un ni ic ca at ti io on n C Co om mm mi is ss si io on n I In nt te er rf fe er re en nc ce e S St ta at te
em me en nt t
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment must be installed and operated in accordance with provided instructions and a
minimum 20 cm spacing must be provided between computer mounted antenna and person’s body
(excluding extremities of hands, wrist and feet) during wireless modes of operation.
The equipment version marketed in US is restricted to usage of the channels 1-11 only.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT
AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the
mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment
and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure
the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France,
Germany, Greece, Ireland, Italy, Luxembourg, Bulgaria, Cyprus, Czech Republic, Estonia, Hungary, Latvia,
Lithuania, Malta, Poland, Romania, Slovakia, Slovenia, the Netherlands, Portugal, Spain, Sweden, and the United
Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway,
and Switzerland.
EU Countries not intended for use
None
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interface, in which case the
user may be required to make adequate measures.