Gianni Industries DG-25 Series User manual

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG25 Ver. B Publish:2008.08.01 Page: 1/ 3
The Digital Keyless Entry system
Operation User's Manual
1. Product Characteristic:
Allows up to 49+50 PIN codes
Dual relays programmable On/Off or pulsed or latched mode
Fully Programmable via keypad and master code
Door Reed Switch Input for Anti-Trailing
3 LED display with audible indication
Non-Volatile Memory
Invalid PIN Lock-out
Durable Stainless Steel housing
With vandal resistant screws
2. Specifications:
Operating Voltage: 12~24 Vdc
Current Draw: Average 15mA, Peak 60mA @ 12Vdc
Input: request-to-exit、Door Reed
Output: Dual relays, N.O./N.C./Com. Output (free voltage contact)
Relays Electric Current: 2A MAX @30Vdc ；0.4A @ 120Vac
Relay Activation Time: （＊100、＊200）
Strike Time: 1~99 seconds（adjustable）
Strike mode: Access Timer or Latch
Memory Volume: 49+50 PIN codes
Relay 1 is controlled by 001~049 user slots
Relay 2 is controlled by 050~099 user slots
PIN codes: 5 digit codes only
Operating Temperature: -20~+70℃
Ambient Humidity: 5~95% relative humidity non-condensing
Factory Master Code: 12345
Invalid PIN Lock-out: The system will shut down for 60 seconds while 32 codes of
incorrectly Master Codes enrolled or PIN codes attempted.
EPROM: Non-volatile memory, System will retain all programs and codes after a total
loss of power.

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG25 Ver. B Publish:2008.08.01 Page: 2/ 3
3. The indicator signal chart:
Sound and LED indicator:
Green LED Power on, stand-by
Red LED Relay 1 activated
LED signal
Yellow LED Relay 2 activated
1 Beep Effective PIN codes
2 Beeps Entering 、Exiting from the Program mode
3 Beeps Data computing error 、other operation mistakes
Sound signal
5 Beeps Master Code reset to Factory （12345）
4. Operation Instruction:
Enter Program Mode:
1. Compose twice the master code (Factory master is 「12345」)
→2 beeps →you are now in the "programming mode".
2. After 60 seconds if you have not entered any codes or data, the system will
automatically exit from the programming mode. After 32 wrong codes attempts at the
master code the lockout facility will operate.
Exiting from the program mode:
1. Press「#」to exit from the programming mode.
2. After 60 seconds if you have not entered any codes or data, the system will
automatically exit from the programming mode. After 32 wrong codes attempts at the
master code the lockout facility will operate.
Add PIN codes
Enter the Programming mode, Enter the slot position code 「＊001~＊099」→?????
Input 5 digit PIN codes→(beep) enrolled Æ（repeat）
Press 「#」to exit from the programming mode, or program other operating.
Note 1: The codes「00000」,「12345」or master code are not be used for PIN code.
Note 2: Relay 1 is controlled by 001~049 user slots, Relay 2 is controlled by 050~099
user slots
To Delete a User Code：
Enter the Programming mode→Press the slot position code of your choice to delete
(example "06") →Press「＊006」→「00000」→（beep）→delete→Press「#」to exit
from the programming mode, or programming other operating.
To Program Relocking Timer
Enter the Programming mode,
A. Relay 1：Press「＊100」Followed by the number of seconds the relay should
open→「05」=5 seconds（01 ~99 = seconds）→（beep）→enrolled →Press
「#」to exit from the programming mode, or program other operating.
B. Enter「00」Sets the relay to latching mode. (Correct code entered opens the relay,
and the relay stays open until the correct code is entered again).
C. Relay 2：Press「＊200」Followed by the number of seconds the relay should
open）→「05 =5 seconds (01 ~99 = seconds). →（beep）→enrolled →Press
「#」to exit from the programming mode, or program other operating.
D. Enter「00」Sets the relay to latching mode. (Correct code entered opens the relay,
and the relay stays open until the correct code is entered again).

Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-DG25 Ver. B Publish:2008.08.01 Page: 3/ 3
Changing the Master codes:
Enter the Programming mode, Enter「＊000」Followed by the new 5 digit master
code→（beep）→enrolled→Enter 「#」to exit from the programming mode, or
program other operating.
Master Code reset to Factory 「12345」
Insert the jumper P1Æ1-2 positionÆ5 audible beepsÆReset successfulÆReturn
Insert the jumper to 2-3 position.
5. Wiring diagram:
1
2
3
Fail-Secure
Locking Device 1
Fail-Safe
Locking Device 2
Power Supply
Power Supply
Contact door reed switch
This reed switch is used
to reset the re-locking time
to 0 second when the door
is moved.
(Using N.O. contact in case
of door closed,
changeover to N.C. When
door is moved)
Master Code
reset to
Factory 12345
「」
Push Button 2
Push Button 1
Note:
The suggested wire gauge is #22~26 AWG.
The varistor or diode must be connected across the lock terminal (electromagnet...)
operated by the device. The vartistor controls the overload produced by the strike coil
(EMP).
Egresses switch should be N.O. type.