GIGA-BYTE TECHNOLOGY R182-Z90 User manual

R182-Z90
R182-Z91
R182-Z92
MZ92-FS0 Motherboard With Dual Sockets for AMD EPYCTM 7002 Series Family Processors
User Manual
Rev. 1.0

Copyright
© 2019 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentation:
 User Manual: detailed information & steps about the installation, conguration and use of this
product (e.g. motherboard, server barebones), covering hardware and BIOS.

User Guide: detailed information about the installation & use of an add-on hardware or
software component (e.g. BMC rmware, rail-kit) compatible with this product.
Quick Installation Guide: a short guide with visual diagrams that you can reference easily for
installation purposes of this product (e.g. motherboard, server barebones).
Please see the support section of the online product page to check the current availability of these
documents.
For More Information
For related product specications, the latest rmware and software, and other information please visit our website at
http://www.gigabyte.com
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller
portal: http://reseller.b2b.gigabyte.com
For further technical assistance, please contact your GIGABYTE representative or visit
https://esupport.gigabyte.com/ to create a new support ticket
For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:
server[email protected]

Conventions
The following conventions are used in this user's guide:
NOTE!
Gives bits and pieces of additional
information related to the current topic.
CAUTION!
Gives precautionary measures to
avoid possible hardware or software problems.
WARNING!
Alerts you to any damage that might
result from doing or not doing specic actions.

Server Warnings and Cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING!
To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING!
To reduce the risk of personal injury from hot surfaces, allow the drives
and the internal system components to cool before touching them.
WARNING!
This server is equipped with high speed fans. Keep away from hazardous
moving fan blades during servicing.
WARNING!
This equipment is not suitable for use in locations where children are
likely to be present.
CAUTION!
• Do not operate the server for long periods with the access panel open or removed. Operat-
ing the server in this manner results in improper airow and improper cooling that can lead to
thermal damage.
• Danger of explosion if battery is incorrectly replaced.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU
PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,
PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-
TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by
their edges without any component and pin touching. After removing a board from its protective
wrapper or from the system, place the board component side up on a grounded, static free sur-
face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over
any surface.
System power on/off: To remove power from system, you must remove the system from
rack. Make sure the system is removed from the rack before opening the chassis, adding, or
removing any non hot-plug components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be
present on power, telephone, and communication cables. Turn off the system and discon-nect
the cables attached to the system before servicing it. Otherwise, personal injury or equipment
damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,
boards, and other parts. We recommend that you perform all procedures in this chapter only at
an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic
wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling
parts.
ESD and handling boards: Always handle boards carefully. They can be extremely
sensi-tive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a
board from its protective wrapper or from the system, place the board component side up on a
grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.
Do not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips
over two jumper pins. Some jumpers have a small tab on top that can be gripped with n-gertips
or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when
using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with
the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the
jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to
grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the
board may bend or break.

CAUTION!
Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery
only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-
teries according to the manufacturer’s instructions.

- 7 -
Table of Contents
Chapter 1 Hardware Installation ................................................................................... 11
1-1 Installation Precautions.................................................................................. 11
1-2 Product Specications.................................................................................... 12
1-3 System Block Diagram................................................................................... 17
Chapter 2 System Appearance.....................................................................................19
2-1 Front View...................................................................................................... 19
2-1-1 R182-Z90................................................................................................................19
2-1-2 R182-Z91 / R182-Z92.............................................................................................19
2-2 Rear View....................................................................................................... 20
2-3 Front Panel LED and Buttons ........................................................................ 21
2-3-1 R182-Z90................................................................................................................21
2-3-2 R182-Z91 / R182-Z92.............................................................................................22
2-4 Rear System LAN LEDs................................................................................. 23
2-5 Power Supply Unit (PSU) LED....................................................................... 24
2-6 Hard Disk Drive LEDs .................................................................................... 25
Chapter 3 System Hardware Installation ......................................................................27
3-1 Removing Chassis Cover............................................................................... 28
3-2 Removing and Installing the Fan Duct ........................................................... 29
3-3 Removing the Heat Sink ................................................................................ 30
3-4 Installing the CPU .......................................................................................... 31
3-5 Installing the Memory..................................................................................... 33
3-5-1 Eight Channel Memory Conguration.....................................................................33
3-5-2 Installing a Memory ...............................................................................................34
3-5-3 DIMM Population Table ..........................................................................................34
3-6 Installing the PCI Expansion Card ................................................................. 36
3-7 Installing the Mezannine Card........................................................................ 37
3-7-1 OCP 3.0..................................................................................................................37
3-7-2 OCP 2.0..................................................................................................................38
3-8 Installing the Hard Disk Drive......................................................................... 39
3-8-1 R182-Z90................................................................................................................39
3-8-2 R182-Z91 / R182-Z92.............................................................................................41
3-9 Installing the M.2 Device and Heat Sink ........................................................ 42
3-10 Replacing the Fan Assembly.......................................................................... 43
3-11 Replacing the Power Supply .......................................................................... 44

- 8 -
3-12 Cable Routing ................................................................................................ 45
3-12-1 Cable Routing for R182-Z90...................................................................................45
3-12-2 Cable Routing for R182-Z91...................................................................................48
3-12-3 Cable Routing for R182-Z92...................................................................................51
Chapter 4 Motherboard Components ...........................................................................57
4-1 Motherboard Components ............................................................................. 57
4-2 Jumper Setting .............................................................................................. 59
Chapter 5 BIOS Setup ..................................................................................................61
5-1 The Main Menu .............................................................................................. 63
5-2 Advanced Menu ............................................................................................. 66
5-2-1 Trusted Computing .................................................................................................67
5-2-2 PSP Firmware Versions..........................................................................................68
5-2-3 Legacy Video Select...............................................................................................69
5-2-4 AST2500 Super IO Conguration...........................................................................70
5-2-5 S5 RTC Wake Settings...........................................................................................72
5-2-6 Serial Port Console Redirection .............................................................................73
5-2-7 CPU Conguration..................................................................................................76
5-2-8 PCI Subsystem Settings.........................................................................................77
5-2-9 USB Conguration..................................................................................................79
5-2-10 NVMe Conguration ...............................................................................................81
5-2-11 SATA Conguration.................................................................................................82
5-2-12 Network Stack Conguration..................................................................................83
5-2-13 AMD Mem Conguration Status.............................................................................84
5-2-14 iSCSI Conguration................................................................................................85
5-2-15 Tls Auth Conguration ............................................................................................86
5-2-16 Intel(R) I350 Gigabit Network Connection ..............................................................87
5-2-17 VLAN Conguration................................................................................................89
5-2-18 MAC IPv4 Network Conguration...........................................................................91
5-2-19 MAC IPv6 Network Conguration...........................................................................92
5-3 AMD CBS Menu............................................................................................. 93
5-3-1 Valhalla Common Options ......................................................................................94
5-3-2 DF Common Options..............................................................................................97
5-3-3 UMC Common Options ........................................................................................100
5-3-4 NBIO Common Options........................................................................................102
5-3-5 FCH Common Options .........................................................................................107
5-3-6 NTB Common Options .........................................................................................110
5-3-7 SOC Miscellaneous Control ................................................................................. 111
5-4 AMD PBS Option Menu ............................................................................... 112
5-4-1 RAS ......................................................................................................................113

- 9 -
5-5 Chipset Setup Menu..................................................................................... 115
5-6 Server Management Menu........................................................................... 116
5-6-1 System Event Log ................................................................................................118
5-6-2 View FRU Information ..........................................................................................119
5-6-3 BMC Network Conguration .................................................................................120
5-6-4 IPv6 BMC Network Conguration.........................................................................121
5-7 Security Menu .............................................................................................. 122
5-7-1 Secure Boot..........................................................................................................123
5-8 Boot Menu.................................................................................................... 125
5-8-1 UEFI NETWORK Drive BBS Priorities .................................................................127
5-8-2 UEFI Application Boot Priorities............................................................................128
5-9 Save & Exit Menu......................................................................................... 129
5-10 ABL POST Codes ........................................................................................ 130
5-10-1 StartProcessorTestPoints .....................................................................................130
5-10-2 Memory test points ...............................................................................................130
5-10-3 PMU Test Points ...................................................................................................130
5-10-4 Original Post Code ...............................................................................................131
5-10-5 CPU test points.....................................................................................................132
5-10-6 Topology test points..............................................................................................132
5-10-7 Extended memory test point.................................................................................132
5-10-8 Gnb Earlier init......................................................................................................133
5-10-9 PMU test points ....................................................................................................136
5-10-10 ABL0 test points ...................................................................................................136
5-10-11 ABL5 test points................................................................................................136
5-11 Agesa POST Codes..................................................................................... 140
5-11-1 Universal Post Code.............................................................................................140
5-11-2 [0xA1XX] For CZ only memory Postcodes...........................................................140
5-11-3 S3 Interface Post Code ........................................................................................143
5-11-4 PMU Post Code....................................................................................................143
5-11-5 [0xA5XX] assigned for AGESA PSP Module........................................................143
5-11-6 [0xA9XX, 0xAAXX] assigned for AGESA NBIO Module.......................................146
5-11-7 [0xACXX] assigned for AGESA CCX Module.......................................................148
5-11-8 [0xADXX] assigned for AGESA DF Module..........................................................149
5-11-9 [0xAFXX] assigned for AGESA FCH Module........................................................149
5-12 BIOS POST Beep code (AMI standard)....................................................... 151
5-12-1 PEI Beep Codes ...................................................................................................151
5-12-2 DXE Beep Codes .................................................................................................151
5-13 BIOS Recovery Instruction........................................................................... 152

- 10 -
This page left intentionally blankThis

- 11 - Hardware Installation
1-1 Installation Precautions
The motherboard/system contain numerous delicate electronic circuits and components which
can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully
read the service guide and follow these procedures:
 • Priorto installation,do notremove or break motherboard S/N(Serial Number)sticker or
warrantystickerprovidedbyyourdealer.Thesestickersarerequiredforwarrantyvalidation.
 • AlwaysremovetheACpowerbyunpluggingthepowercordfromthepoweroutletbefore
installing or removing the motherboard or other hardware components.
 • Whenconnectinghardwarecomponentsto the internalconnectorsonthe motherboard,
makesuretheyareconnectedtightlyandsecurely.
 • Whenhandlingthemotherboard,avoidtouchinganymetalleadsorconnectors.
 • Itisbesttowearanelectrostaticdischarge(ESD)wriststrapwhenhandlingelectronic
componentssuchasamotherboard,CPUormemory.Ifyou do nothaveanESDwrist
strap,keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
 • Beforeunplugging the powersupplycablefromthemotherboard,makesurethepower
supply has been turned off.
 • Beforeturningonthepower,makesurethepowersupplyvoltagehasbeensetaccordingto
the local voltage standard.
 • Beforeusingtheproduct,pleaseverifythatallcablesandpowerconnectorsofyour
hardware components are connected.
 • To prevent damage tothe motherboard,do notallow screws to come incontact withthe
motherboard circuit or its components.
 • Makesuretherearenoleftoverscrewsormetalcomponentsplacedonthemotherboardor
within the computer casing.
 • Donotplacethecomputersystemonanunevensurface .
 • Donotplacethecomputersysteminahigh-temperatureenvironment.
 • Turningonthecomputerpowerduringtheinstallationprocesscanleadtodamageto
system components as well as physical harm to the user.
 • Ifyouareuncertainaboutanyinstallationstepsorhaveaproblemrelatedtotheuseofthe
product,pleaseconsultacertiedcomputertechnician.
Chapter 1 Hardware Installation

Hardware Installation - 12 -
1-2 Product Specications
CPU AMDEPYCTM 7002 Series processor family
Dualprocessors,7nm,SocketSP3
Upto64-core,128threadsperprocessor
TDPupto225W
CompatiblewithAMDEPYC™7001seriesprocessorfamily
NOTE:IfonlyoneCPUisinstalled,somePCIeormemoryfunctionsmightbe
unavailable.
Chipset System-on-Chip
Memory 32xDIMMslots
DDR4memorysupportedonly
8-Channelmemoryperprocessorarchitecture
RDIMMmodulesupto64GBsupported
LRDIMMmodulesupto128GBsupported
Memoryspeed:Upto3200MHz(1DPC),2933MHz(2DPC)
LAN 2x1GbELANports(1xIntel®I350-AM2)
1x10/100/1000managementLAN
ExpansionSlot R182-Z90
Riser Card CRS101E:
-1xPCIex16slot(Gen4x16),FHHL
Riser Card CRS101E:
-1xPCIex16slot(Gen4x16),FHHL
1xOCP3.0mezzanineslotwithPCIeGen4x16bandwidthfromCPU_0
SupportedNCSIfunction
1xOCP2.0mezzanineslotwithPCIeGen3x8bandwidth(Type1,P1,P2)
SupportedNCSIfunction
1xM.2slot:
-M-key
-PCIeGen3x4
-SupportsNGFF-2242/2260/2280/22110cards

-13- Hardware Installation
ExpansionSlot R182-Z91
Riser Card CRS101E:
-1xPCIex16slot(Gen4x16),FHHL
Riser Card CRS101E:
-1xPCIex16slot(Gen4x16),FHHL
1xOCP3.0mezzanineslotwithPCIeGen4x16bandwidthfromCPU_0
SupportedNCSIfunction
1xOCP2.0mezzanineslotwithPCIeGen3x8bandwidth(Type1,P1,P2)
SupportedNCSIfunction
1xM.2slot:
-M-key
-PCIeGen3x4
-SupportsNGFF-2242/2260/2280/22110cards
R182-Z92
RiserCardCRS101E:
-1xPCIex16slot(Gen4x16),FHHL

RiserCardCRS101E:
-1xPCIex16slot(Gen4x16),FHHL

1xOCP3.0mezzanineslotwithPCIeGen4x16bandwidthfromCPU_0
SupportedNCSIfunction

1xOCP2.0mezzanineslotwithPCIeGen3x8bandwidth(Type1,P1,P2)
SupportedNCSIfunction

1xM.2slot:
-M-key
-PCIeGen3x4
-SupportsNGFF-2242/2260/2280/22110cards
Video IntegratedinAspeed®AST2500
2DVideoGraphicAdapterwithPCIebusinterface
1920x1200@60Hz32bpp

Hardware Installation -14-
Storage R182-Z90
4x3.5"hot-swappableHDD/SSDbays
2.5"HDD/SSDsupported
NOTE:SAScardisrequiredforSASdevicessupport
R182-Z91
8x2.5"SATA/SAS
2x2.5"NVMehot-swappableHDD/SSDbays
NOTE:SAScardisrequiredforSASdevicessupport
R182-Z92
10x2.5"NVMehot-swappableSSDbays
SAS N/A
Internal
Connectors
1xM.2slot
1xUSB3.0header
1xCOMheader
1xTPMheader
1xFrontpanelheader
1xHDDbackplaneboardheader
1xPMBusconnector
1xIPMBconnector
1xClearCMOSjumper
1xBIOSrecoveryjumper
FrontPanel
LED/Buttons
2xUSB3.0
1xPowerbuttonwithLED
1xIDbuttonwithLED
1xNMIbutton
1xResetbutton
2xLANactivityLEDs
1xHDDactivityLED
1xSystemstatusLED
RearPanelI/O 2xUSB3.0
1xVGA
2xRJ45
1xMLAN
1xIDbuttonwithLED
BackplaneI/O BackplaneP/N:9CBP10A3NR-00
Speed and bandwidth:
SAS12Gb/s,SATA6Gb/s,PCIeGen3x4
TPM 1xTPMheaderwithLPCinterface
OptionalTPM2.0kit:CTM000

- 15 - Hardware Installation
System
Management
Aspeed®AST2500managementcontroller
AMIMegaRACSP-XSolutionwebinterface
Dashboard
JAVABasedSerialOverLAN
HTML5KVM
SensorMonitor(Voltage,RPM,Temperature,CPUStatus…etc.)
SensorReadingHistoryData
FRUInformation
SELLoginLinearStorage/CircularStoragePolicy
HardwareInventory
FanProle
SystemFirewall
PowerConsumption
PowerControl
LDAP/AD/RADIUSSupport
Backup&RestoreConguration
RemoteBIOS/BMC/CPLDUpdate
EventLogFilter
UserManagement
MediaRedirectionSettings
PAMOrderSettings
SSL Settings
SMTPSettings
Power Supply 2x1200WredundantPSUs
80PLUSPlatinum
ACInput:
-100-240V~/12-7A,50-60Hz
DCInput:
-240Vdc/6A
DCOutput:
-Max1000W/100-240V~
+12V/80.5A
+12Vsb/3A
-Max1200W/200-240V~or240Vdcinput
+12V/97A
+12Vsb/3A
Environment
Ambient
Temperature
Relative
Humidity
Operatingtemperature:10°Cto35°C
Operatinghumidity:8-80%(non-condensing)
Non-operatingtemperature:-40°Cto60°C
Non-operatinghumidity:20%-95%(non-condensing)

Hardware Installation -16-
System
Dimension
1U
438mm(W)x43.5mm(H)x730mm(D)
*Wereservetherighttomakeanychangestotheproductspecicationsandproduct-relatedinformationwithoutprior
notice.

- 17 - Hardware Installation
1-3 System Block Diagram

Hardware Installation -18-

- 19 - System Appearance
Chapter 2 System Appearance
2-1 Front View
2-1-1 R182-Z90
1 2
HDD0 HDD1 HDD2 HDD3
No. Description
1. Front USB 3.0 ports
2. Front Panel LEDs and buttons
2-1-2 R182-Z91 / R182-Z92
1 2
HDD0 HDD2 HDD4 HDD6 HDD8
HDD1 HDD3 HDD5 HDD7 HDD9
No. Description
1. Front USB 3.0 ports
2. Front Panel LEDs and buttons
• PleaseGo to Chapter 2-3 Front Panel LED and Buttons for detail description of function
LEDs.

System Appearance - 20 -
2-2 Rear View
78 6 45 3 2
1
PSU2 PSU1
No. Description
1. PCIecardslotx2
2. Mezzaninecardslot(Option/OCP3.0/SFF)
3. IDbuttonwithLED
4. 10/100/1000 Server management LAN port
5. GbELANportx2
6. USB3.0portx2
7. Mezzaninecardslot(Option/OCP2.0)
8. VGAport