Gigabyte 6BXD User manual

R-01-01-080514
6BXD
USER'S MANUAL
1. System power on by PS/2 Mouse: If you are using ATX power
supply, you are able to power on the system by double
clicking the right or left button of your PS/2 Mouse.
2. System power on by Keyboard: If your ATX power supply
supports larger than 720 mA 5V Stand-By current, you can
power on your system by entering password from the
Keyboard after setting the “Keyboard power on”jumper (JP1)
and password in CMOS Setup.
3. Modem Ring-On on COM B.
4. Wake-Up on LAN. (The ATX power supply supports larger
than 600 mA)
5. Support 3 steps ACPI LED selectable.
Pentium

II Processor MAINBOARD
REV. 1 First Edition

6BXD
1
The author assumes no responsibility for any errors or omissions which may
appear in this document nor does it make a commitment to update the
information contained herein.
Third-party brands and names are the property of their respective
owners.
Sound Blaster is a registered trademark of Creative Technology Ltd in the
United States and certain other countries. Sound Blaster-LINK and SB-LINK
are trademarks of Creative Technology Ltd.
MAY 14, 1998 Taipei, Taiwan

Quick Installation Guide
2
I. Quick Installation Guide :
CPU SPEED SETUP
The system bus speed can be selectable between 66.6MHz and 100MHz. The
user can select the system bus speed (JP10) and change the DIP SWITCH
(SW) selection to set up the CPU speed for 200 - 633MHz processor.
M The CPU speed must match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than CPU's.
DIP SWITCH (SW)
FREQ. RATIO 1234
X 3 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
MJP10 (Select the system speed between 66.6MHz and 100MHz)
1-2 Close System speed is set to 66MHz
− system always
run at 66MHz FSB (Front Side Bus).
All Open System speed is set to 100MHz
− system always
run at 100MHz FSB (Front Side Bus).
2-3 Close Set system speed to Auto
− system speed
detect automatically (66 / 100MHz FSB).
1
2
3
1
2
3
1
2
3

6BXD
3
MThere are two ways to set system speed
1. 66MHz (JP10) (1-2 short) or Auto detect (2-3 short)
2. 100MHz (JP10) (1-2-3 open) or Auto detect (2-3 short)
1. PentiumII 300 / 100MHz FSB
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
2. PentiumII 350 / 100MHz FSB
3. PentiumII 400 / 100MHz FSB
SW
ON
1 2
SW
1 2
ON
Open
Open
JP10
1
2
3
1
2
3JP10
SW
ON
OFF
4
3
2
1
Open
JP10
1
2
3
JP10
1
2
32-3
Close
2-3
Close
JP10
1
2
3
100 MHz or Auto
Detect
100 MHz or Auto
Detect
2-3
Close
JP10
1
2
3

Quick Installation Guide
4
4. PentiumII 450 / 100MHz FSB
5. PentiumII 233 MHz / 66MHz FSB
6. PentiumII 266 / 66MHz FSB
7. PentiumII 300 MHz / 66MHz FSB
SW
ON
1 2
SW
ON
1 2
SW
ON
1 2
SW
ON
1 2
Open
1-2 Short
1-2 Short
1-2 Short
JP10
1
2
3
JP10
1
2
3
JP10
1
2
3
JP10
1
2
3
2-3
Close
JP10
1
2
3
100 MHz or Auto
Detect
66 MHz or Auto
Detect
2-3
Close
JP10
1
2
3
66 MHz or Auto
Detect
2-3
Close
JP10
1
2
3
2-3
Close
JP10
1
2
3
66 MHz or Auto
Detect

6BXD
5
8. PentiumII 333 / 66MHz FSB
II. Jumper setting :
9. PentiumII 366 / 66MHz FSB
SPK : Speaker Connector
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
Pin No. Function
1
2
VCC
NC
3
NC
4Data
1
SW
ON
1 2
1-2 Short
JP10
1
2
32-3
Close
JP10
1
2
3
66 MHz or Auto
Detect
SW
ON
1 2
JP10
1
2
32-3
Close
JP10
1
2
3
66 MHz or Auto
Detect
1-2 Short

Quick Installation Guide
6
RST : Rest Switch
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
1
Open:
Normal operation
Short:
For Hardware
Reset System
1
PWR : Power LED
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
1
Pin No. Function
1
2
LED anode (+)
LED athode (-)
3
LED athode (-)

6BXD
7
HD : IDE Hard Disk Active LED
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
1
Pin No. Function
1
2
LED anode (+)
3
4LED anode (+)
LED cathode (-)
NC
IR : Infrared Connector
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
1
GND
IR Data Input
Pin No. Function
1
2
IR Data Output
3
4NC
POWER (+)
5

Quick Installation Guide
8
GN : Green Function Switch
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
1
Open:
Normal operation
Short:
Entering Green Mode.
1
Soft PWR : Soft Power Connector
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
1
Open:
Normal operation
1
Short(Two Option):
1.Instant On/Off: Power
On/Off system immediately
2.Delay 4Seconds:
Power Off system Press
over 4 Secs.

6BXD
9
GD : Green Function Active LED Connector
CPU2
686BXD
CPU1
PIIX4
82443BX
JP10
1
Pin No. Function
1
2
LED anode (+)
LED athode (-)
POWER : Power Connector
CPU2
6BXD
CPU1
PIIX4
82443BX
JP10
1
VCC (+5V)
Power Good
Pin No. Function
4,6,19,20
GND
10
12
18
8
+12V
-12V
-5V
9
14 PS-ON
(Soft ON/OFF)
5V SB
(Stand by +5V)
13,15-17
3,5,7