Gigabyte 6WXM User manual

R-13-01-090827
6WXM
USER'S MANUAL
1. System power on by PS/2 Mouse: First, enable this function
in CMOS Setup, then you can power on the system by
double clicking the right or left button of your PS/2 Mouse.
2. System power on by Keyboard: If your ATX power supply
supports larger than 300 mA 5V Stand-By current (depends
on the specification of keyboards), you can power on your
system by entering password from the Keyboard after
setting the “Keyboard power on”jumper and password in
CMOS Setup.
3. Support 3 steps ACPI LED selectable.
4. Support Modem Ring-On (Include internal Modem and
external modem on COM A and COM B).
5. Support Wake-up On LAN (Your ATX power supply must
support larger than 720 mA 5V Stand-By current).
Pentium

II / III / Celeron Processor MAINBOARD
REV. 1.3 First Edition

6WXM
1
The author assumes no responsibility for any errors or omissions that may
appear in this document nor does it make a commitment to update the
information contained herein.
Third-party brands and names are the property of their respective owners.
August 27, 1999 Taipei, Taiwan

Quick Installation Guide
2
I. Quick Installation Guide :
CPU SPEED SETUP
The system bus frequency can be switched between 66¡B100MHz and
by adjusting JP6 & JP28 (See Figure-1). The CPU Frequency is
control by BIOS.
M The CPU speed must match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than that of
CPU.
JP6 / JP28: System Bus Speed
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
JP6
1
CPU JP6 JP28
AUTO 1-2 1-2
66 2-3 2-3
100 NC 2-3
133 NC NC
1
JP28
Figure-1
« Note: Please set the CPU host frequency in accordance with your
processor’s specifications. We don’t recommend you to set the
system bus frequency over the CPU’s specification because these
specific bus frequencies are not the standard specifications for
CPU, chipset and most of the peripherals. Whether your system can
run under these specific bus frequencies properly will depend on
your hardware configurations, including CPU, Chipsets, SDRAM,
Cards….etc.
« Note: JP28 is only available when the motherboard use 82810E
Chipset.

6WXM
3

Quick Installation Guide
4
II. Jumper setting :
GN : Green Function Switch
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PIN No. Function
Open
Normal Operation
Close Entering Green
Mode
GD : Green Function LED
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PIN No.
Function
1LED +
2LED −
+
−
1

6WXM
5
HD : IDE Hard Disk Active LED
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888 PIN No. Function
1LED +
2LED −
−
+
1
SPKR: External Speaker Connector
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
External Speaker
+1
PIN No.
Function
1VCC
2NC
3NC
4Data

Quick Installation Guide
6
RES : Reset Switch
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PIN No. Function
Open Normal
Operation
Short Reset Hardware
System
P+P−P−: Power LED Connector (as 3 steps ACPI LED)
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PIN No.
Function
1LED +
2LED −
3LED −
+
−
−
1

6WXM
7
PW: Soft Power Connector
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PIN No.
Function
Open
Normal Operation
Close Power ON/OFF
IR : Infrared Connector (IR / CIR)
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PIN
No. Function
1VCC
2NC
3IRRX
4GND
5IRTX
6NC
7CIRRX
8VCC
9NC
10 CIRTX
10 1
2
34
5
6
789

Quick Installation Guide
8
PS/2 Mouse / Keyboard Connector
6WXM
ICH/
82801
GMCH-E/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PS/2 Mouse/ Keyboard
Pin No. Function
1Data
2NC
3GND
4VCC(+5V)
5Clock
6NC
PS/2 Keyboard
PS/2 Mouse
12
3
4
56
USB : USB Port
6WXM
ICH/
82801
82810/
82810E
AC97
YMF
744
Main
BIOS
Backup
BIOS
IT8888
PIN No.
Function
1USB V0
2USB D0-
3USB D0+
4GND
5USB V1
6USB D1-
7USB D1+
8GND
1 2 3 4
5 6 7 8