Gigabyte GA-6VXE7+ User manual

R-10-02-000427
6VXE7+
USER'S MANUAL
1. System power on by PS/2 Mouse: First, enable this function
in CMOS Setup, then you can power on the system by double
clicking the right or left button of your PS/2 Mouse.
2. System power on by Keyboard: If your ATX power supply
supports larger than 300 mA 5V Stand-By current (depends
on the specification of keyboards), you can power on your
system by entering password from the Keyboard after setting
the “Keyboard power on” jumper and password in CMOS
Setup.
3. Support 3 steps ACPI LED selectable.
4. Support Modem Ring-On. (Include internal Modem and
external modem on COM A and COM B)
5. Support Wake-up On LAN. (Your ATX power supply must
support larger than 720 mA 5V Stand-By current)
CeleronTM /Pentium®!!! Socket 370 Processor Motherboard
REV. 1.0 Second Edition

6VXE7+
1
The author assumes no responsibility for any errors or omissions which may
appear in this document nor does it make a commitment to update the
information contained herein.
Third-party brands and names are the property of theirrespectiveowners.
Sound Blaster is a registered trademark of Creative Technology Ltd in the
United States and certain other countries. Sound Blaster-LINK and SB-LINK
are trademarks of Creative Technology Ltd.
Apr. 27, 2000 Taipei, Taiwan

Quick Installation Guide
2
I. Quick Installation Guide :
The system bus speed can be set for 66,100,133MHz. The user can select the
system bus speed(SW2) and change the DIP SWITCH(SW1) selection to set
up the CPU speed for 300-866MHz processor.
M The CPU speed must match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than CPU's.
SW1:(O:ON / X:OFF)
DIP SWITCH (SW)
FREQ. RATIO 1234
X 3 OXOO
X 3.5 XXOO
X 4 OOXO
X 4.5 XOXO
X 5 OXXO
X 5.5 XXXO
X 6 OOOX
X 6.5 XOOX
X 7 OXOX
X 7.5 XXOX
X 8 OOXX
X 8.5 XOXX
X 9 OXXX
X 9.5 XXXX

6VXE7+
3
Set System Bus Speed
SW2: (O:ON / X:OFF)
CPU PCICLK 1 23 456
66/100/
133/Auto 33.3 XXXXOO
66 33.3 OOXXXX
75 37.5 OOOXXX
83 41.6 OOXOXX
100 33.3 OXXXXX
112 37.3 OXOXXX
124 31 XXXOXX
133 33.3 XXXXXX
140 35 XXOOXX
150 37.5 XXOXXX
M Note: We don’t recommend you to set up your system speed to
75,83,112,124,140 or 150MHz because these frequencies are not
the standard specifications for CPU, Chipset and most of the
peripherals. Whether your system can run under
75,83,112,124,140 or 150 MHz properly will depend on your
hardware configurations: CPU, SDRAM, Cards, etc.
1. CeleronTM 300A/ 66 MHz FSB
PIIX4
6VXE7+
82443BX
SW1
ON
1 2 3 4
SW2
1 2 3 4 5 6
ON

Quick Installation Guide
4
2. CeleronTM 333/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
3. CeleronTM 366/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
4. CeleronTM 400/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
5. CeleronTM 433/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON

6VXE7+
5
6. CeleronTM 466/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
7. CeleronTM 500/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
8. CeleronTM533/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
9. CeleronTM 566/ 66 MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON

Quick Installation Guide
6
10. Cyrix Joshua 300/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
11. Pentium®!!! 500/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
12. Pentium®!!! 550/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
13. Pentium®!!! 600/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON

6VXE7+
7
14. Pentium ®!!! 650/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
15. Pentium ®!!! 700/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
16. Pentium ®!!! 750/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
17. Pentium ®!!! 800/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON

Quick Installation Guide
8
18. Pentium ®!!! 850/100MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
19. Pentium®!!! 533/133MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON
20. Pentium®!!! 600/133 MHz FSB
SW2
1 2 3 4 5 6
ON
SW1
ON
1 2 3 4
21. Pentium®!!!667/133MHz FSB
SW2
1 2 3 4 5 6
SW1
ON
1 2 3 4
ON