Gilbarco Advantage Series User manual

®
94
ECONOMY
REGULAR
PLUS PREMIUM
SPECIAL
92
89
87
86
7
4
1
8
5
2
0
9
6
3
94
ECONOMY
REGULAR
PLUS PREMIUM
SPECIAL
92
89
87
86 94
REGULAR
DIESEL
$
$
THISSALE
GALLONS
PRICE/GALLON
TAXESINCLUDED
PUMPON
PUMPOFF
PUMPON
PUMPOFF
7
4
1
8
5
2
0
9
6
3
Unleaded
Plus
Super
89
91
93
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Unleaded
Super
7
4
1
8
5
2
0
9
6
3
Plus
89
91 93
1.REMOVE NOZZLE PLACE IN CAR FULE TANK.
2.LIFTHOOK ''ON'' WAITUNTIL COMPUTER
RESETSTOZERO.
3.OPERATENOZZLEFORGASOLINE.
4.AFTER COMPLETING DELIVERY. LOWERHOOK
''OFF''ANDHANGNOZZLEUP.
DONOTLOWER HOOK ''OFF'' UNTIL YOU
FINISHEDDELIVERY.
AFTERARRANGINGPURCHASEWITHCASHER
PROCEEDASFOLLOWS.
NOSMOKING-SHUT OFF ENGINE
CAUTION
UNLEADED
REGULAR
$
$
TAXESINCLUDED
PRICE/GALLON
GALLONS
THISSALE
$
$
TAXESINCLUDED
PRICE/GALLON
GALLONS
THISSALE
$
$
TAXESINCLUDED
PRICE/GALLON
GALLONS
THISSALE
$
$
TAXESINCLUDED
PRICE/GALLON
GALLONS
THISSALE
1.REMOVE NOZZLE PLACE IN CAR FULE TANK.
2.LIFT HOOK ''ON'' WAIT UNTIL COMPUTER
RESETSTOZERO.
3.OPERATE NOZZLE FOR GASOLINE.
4.AFTER COMPLETING DELIVERY. LOWERHOOK
''OFF''ANDHANG NOZZLE UP.
DONOTLOWER HOOK ''OFF'' UNTIL YOU
FINISHEDDELIVERY.
AFTERARRANGINGPURCHASE WITH CASHER
PROCEEDASFOLLOWS.
NOSMOKING-SHUT OFF ENGINE
CAUTION
REGULAR
PREMIUM
001
1
GALLONS
Pump and Dispenser
Installation Manual
Please see MDE-2833 for Site Prep Information.
MDE-2530H

Computer
Programs
All Gilbarco computer programs (including software on diskettes and within memory chips) are copyrighted by, and
shall remain the property of, Gilbarco Inc. Such computer programs may also contain trade secret information. The
duplication, disclosure, modification, or unauthorized use of computer programs is strictly prohibited, unless
otherwise licensed by Gilbarco.
FCCWarning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense. Changes or
modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Approvals Underwriters Laboratories:
Gilbarco pumps and dispensers that bear the U.L. listing mark are listed under the U.L. file number MH1941.
National Quality Assurance:
Gilbarco is an ISO9001/BS5750 Part 1/EN29001 registered company, certificate number 5119.
Weights and Measures:
Gilbarco pumps and dispensers are evaluated by the National Institute of Standards and Technology (NIST) under
the National Type Evaluation Program (NTEP). NIST has issued Certificates of Conformace (COC) for the
following:
Model COC# Model COC#
The Advantage Series 90-115-A4 Salesmaker Pro Blender: AB 78-099
MPD-3 Series: AE, AL, AP, AU 87-077A2 Salesmaker Series: AM 88-129
MPD-2 Series: AK 87-077A2 Trimline Series 91-088
MPD-1 Series: AF, AG, AN, AR 89-019A1 Legacy Series 94-027
H111B Series: AC 88-226A3
California Air Resources Board (CARB):
The Executive Order for vapor recovery balance system G-70-52
The Executive Order for VaporVac G-70-150-AB
The Gilbarco approval for TheAdvantage motor fuel dispensers is on attachment “A”.
NewYork City:
The Advantage

Series N.Y.C.F.D. COC #4805 (Refer to MDE-3197 NYC Requirements for approval)
The Legacy

Series N.Y.C.F.D. COC #4879 (Refer to MDE-3197 NYC Requirements for approval)
Permissions:
Gilbarco has been given permission by OPW andASCO to use their illustrations.
Patents Gilbarco products are manufactured or sold under one or more of the following U.S. patents.
D.316,471 4,566,504 4,687,033 4,728,788 4,799,940 4,876,653 4,890,210 4,913,813
4,938,251 4,939,730 4,986,445 5,013,434 5,029,100 5,040,577 5,083,846 5,098,179
5,099,403 5,110,010 5,134,548 5,156,199 5,269,353 5,325,706 5,345,979 5,355,915
Canada Patented 1990 No. 1,276,917
Additional U.S. and foreign patents pending.
Trademarks The following are trademarks of Gilbarco Inc.:
The Advantage

Series MPD

Proportional Flow Control Valve

Super-Hi

VaporVac

G-SITE

MPD

Pro Blender

Salesmaker

Trimline

Highline

MPD

Precision Blender

Salesmaker Pro Blender

Ultra-Hi

The Legacy

Series
Copyrights

1995 Gilbarco Inc. All Rights Reserved
Memberships Gilbarco is a member of the Petroleum Equipment Institute.
This document is subject to change without notice.
For information regarding Gilbarco Literature
call 910-547-5661.
BS5750 Part 1/EN29001 Certificate No. 5119

Introduction
MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95 Page 1
Introduction
Purpose Of
This Manual
This manual gives step by step instructions for installing Gilbarco pumps and
dispensers. It does not include site preparation instructions (see MDE-2833 Pump and
Dispenser Site Prep).After the installation is complete, a GilbarcoAuthorized Service
Contractor must commission the unit to activate the warranty.
This manual has two parts: a base manual with step by step installation instructions
and a model specific addendum for each pump/dispenser model that includes:
• Pump/dispenser specifications
• Model number breakdowns
• Foundation layouts
• External dimensions
• Field wiring diagrams
Reference Manual MDE-2755 Gilbarco STP Control and Dispenser Isolation Relay Box
PA02870000000
Available
Addenda
The Advantage

Series (High-Hose)
MDE-2530-01 The Advantage

MPD

3 and 4-Grade Dispenser
MDE-2530-03 The Advantage MPD 3-Grade Pump
MDE-2530-05 The Advantage Dual and Quad Dispenser
MDE-2530-07 The Advantage Dual and Quad Pump
MDE-2530-09 The Advantage Blender Six-Hose Dispenser
MDE-2530-13 The Advantage Blender Dispenser
MDE-2530-15 The Advnatage Selectable Blender Pum
Highline  Series (Low-Hose)
MDE-2530-21 Highline Standard Gallonage Dispensers
MDE-2530-23 Highline Conventional High Gallonage Dispensers
MDE-2530-25 Highline Super-Hi 
High Gallonage Dispensers
MDE-2530-27 Highline Ultra-Hi 
High Gallonage Dispensers
MDE-2530-29 Satellite High Gallonage Dispensers
MDE-2530-71 Highline Standard Gallonage Pumps
MDE-2530-73 Highline Conventional High Gallonage Pumps
Legacy  Series
MDE-2530-80 Legacy Commercial Pumps and Dispensers
MDE-2530-81 Legacy Electronic Pumps and Dispensers
MDE-2530-82 Legacy Family Hi and Ultra Hi Gallonage Master/Satellite/
Combo
MDE-2530-83 Legacy Mechanical Pumps and Dispensers
Mechanical Series (Low-Hose)
MDE-2530-31 Trimline

and Commercial 625/650 Dispensers
MDE-2530-35 Commercial 684 Pumps/Dispensers
MDE-2530-37 Trimline and Commercial 625/650 Pumps
MDE-2530-39 Commercial 625 Ultra-Hi Dispensers

Introduction
Page 2 MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95
Salesmaker  Series (High-Hose)
MDE-2530-41 Salesmaker  -2H and 4A Pumps/Dispensers
MDE-2530-43 Salesmaker Pro Blender 
Dispensers
MPD

Series (High-Hose)
MDE-2530-51 MPD

-1/3 and MPD Fixed Blender Dispensers
MDE-2530-53 MPD Pro Blender 
Dispensers
MDE-2530-55 MPD Precision Blender 
Dispensers
Remanufactured Models
MDE-2530-61 MPD-2/C Dispensers (with non-modular electronics)
MDE-2530-62 Highline Pumps/Dispensers (with non-modular electronics)
MDE-2530-63 MPD-1 Dispensers (with non-modular electronics)
MDE-2530-64 MPD-A3 Dispensers (with non-modular electronics)
MDE-2530-65 Salesmaker-4 Pumps/Dispensers (with non-modular electronics)
GlossaryTerms STP
Submerged turbine pump
Pump
Uses self-contained pumping unit and motor to move fuel from storage tank
Dispenser
Uses STP in storage tank to move fuel from storage tank
High Hose
Pumps/dispensers with hoses that connect overhead
Low Hose
Pumps/dispensers with hoses that connect at hydraulics level
Master/Satellite
Master dispensers are teamed with satellites for rapid fueling of trucks with saddle
tanks. The master unit meters and computes product flow for both units. The satellite
is a dispenser without the electronics module.
Listed
Products that bear the authorized Listing Mark of U.L. as the manufacturer’s
declaration that the product complies with U.L.’s requirements in accordance with the
terms of U.L.’s Listing and Follow-Up Service agreement.

Introduction
MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95 Page 3
Classifying
Hazardous
Locations
Any activity that can cause an explosion (e.g. smoking, drilling, etc.) must be done
well outside the vapor area.
The following diagrams are based on NFPA 30A, section 6 and NFPA 70, section
514.
Note: The optional field installed canopy (if needed) must be listed for use over
hazardous locations.
Pit box.
Fuel is present.
(Flammable Liquid)
Class 1 Division 2
(Hazardous Location)
Class 1 Division 1
(Hazardous Location)
Fuel Containing
Components
Vapor Areas
18"
18"
Unclassified location
area within electronics cabinet
above Air Gap.
Class 1 Division 1
within boot area.
Air Gap
20'
Pit box.
20'
20'
20'
Unclassified location
Electronics Head
Vapor Barrier
20'
Pit box.
18"
18"
18"
20'
Pit box.
20'
18"
Vapor Barrier
Vertical Vapor Barrier
Vertical Vapor Barrier
48"
Class 1 Division 1
within boot area.
Highline/LegacyElectronic Series The AdvantageSeries with Air Gap
Legacy Commercial/Mechanical Series MPDand SalesmakerSeries withVapor Barrier

Introduction
Page 4 MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95
Safety Alert Symbol
This is a standardANSI* approved alert symbol. When you see this symbol, be alert to
the potential for a personal injury.
* Reference American National Standard Bulletins ANSI Z535.
SignalWords
These are standard ANSI approved signal words. They alert you to personal safety
hazards and precautions.
Safety Symbols
The following safety symbols are used throughout this manual to alert you to personal
safety hazards and precautions.
DANGER
The hazard or unsafe practice
will result in severe injury or
death.
WARNING
The hazard or unsafe practice
could result in severe injury or
death.
CAUTION
The hazard or unsafe practice
could result in minor injury.
Turn power off. Collect fuel in
approved
containers.
G
A
S
Use emergency
power cutoff.
No vehicles
in area.
OFF
No power tools. Wear eye
protection.
Explosive Flammable Electricity
Clean up spills.Read all related
manuals.
Use safety
barricades. No people
in area.
No open
flames. No smoking.

Installation
MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95 Page 5
Installation
Required
Equipment and
Materials
Below is a list of items required to properly install the equipment.
• Lifting device (crane, backhoe, forklift, etc.) to move and lift pump/dispenser
• Nylon slings (with a safety lift factor of 5) and screw-pin anchor shackles to lift
high hose pump/dispenser
• Breakaways, hoses, nozzles, and swivels
• Barricades
Read NFPA 30A
and NFPA 70
Before installing the equipment, read, understand and follow:
• The National Electric Code (NFPA 70)
• The Automotive and Marine Service Code (NFPA 30A)
• Any national, state, and local codes that may apply
The failure to install the equipment in accordance with NFPA 30A and NFPA 70 may
adversely effect the safe use and operation of the system.
Accurate, sound installations reduce service calls: Use experienced, licensed
contractors that practice accurate, safe installation techniques. Careful installation
provides a sound troubleshooting framework for field repairs and can eliminate
potential problems.
Equipment manufacturer must provide instructions for other equipment, such as
submerged turbine pumps (STPs), leak detectors, and underground tanks. Gilbarco
does not provide installation instructions for other manufacturer’s equipment.
Installation
Instructions
1. Read all instructions before beginning.
2. Follow all safety precautions:
• Barricade the area.
• Do not allow vehicles or unauthorized people in the work area.
• Do not smoke or allow open flames in the work area.
• Do not use power tools in the work area.
• Wear eye protection during the installation.
3. Use circuit breakers to turn off all power to pumps/dispensers and STPs. Multiple
disconnects may be required.
WARNING
Dangerous Environment!
Failure to install this equipment
in accordance with NFPA 30A
and NFPA 70 could result in
severe injury or death.
Read, understand and follow
NFPA 30A and NFPA 70.

Installation
Page 6 MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95
4. Check the following for proper installation per criteria in the Pump and Dispenser
Site Preparation Manual (MDE-2833):
Emergency Power Cutoff Switch Piping and Fittings
Circuit Breakers Fuel Storage Tanks
STP Control Relay Boxes Pressure Regulating Valves
(dispensers only) (above ground tanks only)
Isolation Relays (dispensers only) STPs (dispensers only)
Conduit and Wiring Tank Leak Detectors (dispensers only)
Grounding Pit Boxes
Shear Valves (dispensers only)
5. Inspect pump/dispenser cartons and contents for shipping damage. Check tip-and-
tell indicator. Gilbarco does not cover shipping damage under its warranty policy.
Notify the shipper of any damage.
6. Remove lower panels (doors) of pump/dispenser.
7a. For The Advantage

Series remove outer sheathing to access the anchor bolt
holes.
• For one piece sheathing remove the four screws (2) at the top and (2) at the
bottom of the side columns.
• For two piece (painted sheathing) remove only the lower sheathing. You can do
this by removing the two lower screws on the side columns. Grab sheathing at
bottom. Carefully swing out sheathing from under top sheathing and remove.
Note: For The Advantage

Series, bend out the six tabs located inside the column.
These tabs are part of the sheathing. Use needle nose pliers or bent wire to pull
tabs toward inside.
Top Sheathing
Lower
Sheathing
1 Screw
Each Side
One Piece Side
Sheathing
Side Column
Screws (4)
One Piece Sheathing Two Piece (Painted Sheathing)
Outer Sheathing
Folded Tab Column

Installation
MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95 Page 7
8. Remove fiche paper and the lower half of the union on the pump/dispenser
inlet pipe.
9. For dispensers, attach lower half of union to the shear valve. For pumps, attach
lower half of union to riser pipe.
Note: You must install a listed shear valve for every product line at each dispenser. A
shear valve is a NFPA30A required safety device. See the Site Preparation
manual MDE-2833 for installation instructions.
10. Be sure that the fuel grade for the product lines match the pump/dispenser brand
panels and foundation layout. Product lines from the ground should have labels.
11. Place pump/dispenser onto island.
Note: Pumps and dispensers vary in weight. See specifications in the addendum
section. See MDE-2833 for minimum clearance requirements.
High-Hose Models
The Advantage

Series, MPD

and Salesmaker  Series have hoisting brackets
mounted on top of upper housing.
• Use nylon slings (safety lift factor of 5) with hoisting
brackets to lift unit onto island. TheAdvantage Series
requires three nylon slings and four screw pin shackles. The
MPD and Salesmaker series requires two nylon slings and
two screw pin shackles.
Note: Do not run slings around the columns. This will
damage the columns or sheathing.
• Lift and position unit onto island.
• Remove slings and shackles.
Low-Hose Models
Legacy

, Highline  , Highline Salesmaker  , Trimline

,
and Commercial Series units must be placed onto island
using a fork lift.
Note: Do not lift by electronic head.
Upper Half of Union
Lower Half of Union
Pump/Dispenser Base
Remove Fiche Paper
WARNING
Lifting heavy equipment can be
hazardous.
Equipment could fall and cause
severe injury or death. Use
lifting equipment. Stand clear
from pump/dispenser when
lifting and lowering.
Regular
7
4
1
8
5
2
0
9
6
3
Super
94
Plus
91
89

Installation
Page 8 MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95
12. Line up pipes.
Note: 1. Do not anchor unit to island now. Anchor shear valve first.
2. Do not use pry (crow) bar to position dispenser/pump over conduit or pipes.
This could damage valves, junction box or other parts of the unit.
13. Loosely connect union halves together.
Note: Illustrations shown are for dispensers in these steps. Pumps do not use shear
valves. The connection to tank piping for pumps is the same less shear valve.
14. Double check alignment of pipes, conduit, and frame.
Note: Misaligned piping could result in a leak later.
15. Tighten union halves together.
16. Anchor shear valves to island form (concrete or pit box). If you do not anchor the
shear valve, it will not operate correctly during a severe impact. Follow shear
valve manufacturer instructions.
17. Anchor the pump/dispenser securely to the island per foundation layout locations.
(See product specific addendum).
Upper Half of Union
Lower Half of Union
Pump/Dispenser Base
Align Union
Halves Together
WARNING
Install shear valves correctly.
Fire/Explosion could result in
severe injury or death. Anchor
the shear valve per
manufacturer’s instructions
Anchor Bracket Pump/Dispenser Base
WARNING
Fire/Explosion could result in
severe injury or death.
NFPA 30A requires anchoring
pumps/dispensers. Install all
anchor bolts on the unit for safe
operation of shear valves and
hose breakaways.
Anchor Bolts

Installation
MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95 Page 9
Run field wiring to the main junction box through 1" conduit for TheAdvantage
series. Use 3/4" conduit for all other pumps/dispensers. Run external speaker wires
(option) to conduit outlet box (see illustration below). Use Seal-Off (“Y”) fittings as a
first connection where conduit leaves ground. Keep open ends up.
Note: 1.Wire all pumps/dispensers under NFPA 30A, NFPA 70, and applicable
national, state and local codes and regulations. Wire all circuits N.E.C.
Class 1, except outputs to speaker (intercom) which must be N.E.C. Class 2.
Gilbarco two-wire is N.E.C. Class 1 and may share the main power conduit.
2. All field wiring (except speaker) enters the pump/dispenser through the AC
Main Junction Box on the “A” Side of the pump/dispenser. Speaker wiring
enters through an optional conduit outlet box (see Elevation/Footprint in
specific addendum). Gilbarco recommends only licensed electricians wire
pumps/dispensers.
18. Tighten conduit unions.
19. Test wire insulation before connecting wires. This checks for damage that can
occur while pulling wires through the conduit.
• Disconnect wires at both ends. If you do not disconnect wires at both ends, you
can damage the pump/dispenser electronics.
• Test the conduit wiring ends by using a insulation/megger tester.
• Connect one tester lead to wire under test.
• Connect other tester lead to ground.
• Measure resistance. Follow test set manufacturer instructions. Insulation
resistance more than 50 megohms is satisfactory. Check local authority
requirements.
• Repeat above steps for all wires.
• Repeat test between all wires.
20. Seal each conduit entering and exiting pump/dispenser by pouring sealing
compound into open leg of “Y” fitting. The compound thickness shall not be
less than the trade size of the conduit and never less than 5/8" (see NFPA 70
Section 510-5 [C.3]).
21. Attach grounding wire to green grounding screw in junction box.
22. Make connections in junction box (see field wiring diagrams). Do not disturb
sealing compound around wire in existing conduit. Do not disturb factory wiring
in electronic cabinet.
The Advantage
Main Junction Box
(located on Aside)
Conduit Outlet Box
(for speaker option)
WARNING
Sparks can ignite Fuel/Vapors.
Fire/Explosion can result in
severe injury or death. Use
caution when testing wires. Do
not test when exposed fuel and
vapors are present.

Installation
Page 10 MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95
23. For units with lighted canopies:
Note: Use lighted canopies listed for use over hazardous locations. You must use the
following installation method to meet NFPA 30A requirements.
• Remove upper housing cover to expose canopy light conduit and wires.
• Rotate conduit elbow, nipple, and wires 90 degrees so they point upward.
• Remove knockout from upper housing cover. Make sure the hole aligns with the
upturned conduit.
• Place a nut and then a washer on conduit below upper housing cover. Position
nut and washer to meet bottom-side of housing cover. Replace piping housing
cover so the upturned conduit nipple sticks through knockout hole. Place a
washer and then a nut on conduit above cover (see illustration). Washers must be
against housing cover.
Note: Do not use canopy conduit for running wires to station overhead canopy lights,
fore court lights, or to other equipment.
24. Use wire nuts or lugs to make good connections. Cap all unused wires.
25. Use pipe plugs to seal unused openings in junction boxes.
26. Double check all wiring connections for wire nuts, lugs, caps, etc. Replace
junction box cover and tighten all bolts. Do not use gaskets on junction box. Do
not pinch wires.
27. Replace lower doors and side sheathing.
Rotate elbow 90 degrees so it points
up thru the opening (knock-out) in
the Upper Housing Cover.
Pump/Dispenser
Canopy Washers
Upper
Housing
Cover
Front View
(“A”side) Side View
Nut
Nut
Washers
WARNING
High Voltage
Electrical shock can result in
severe injury or death.
Replace all bolts and tighten
junction box cover before
turning on unit AC power.

Installation
MDE-2530H Gilbarco Pump and Dispenser Installation Manual • 03/95 Page 11
28. Install listed breakaways to hoses. Follow breakaway manufacturer instructions.
• Clean all threads.
• Place sealant on male threads only. Follow sealant manufacturer instructions.
Note: Use only listed pipe sealant for use with petroleum products. Remove sealant if
it gets inside hose or fittings. Clean off excess sealant. Do not use teflon tape or
damage to unit may occur.
• Use a smooth faced wrench to tighten all fittings securely. Do not over-tighten.
Note: Do not tighten breakaway by twisting hose. This could damage coupling.
29. For high-hose units, install breakaway to pump/dispenser outlet. For low-hose
units, install between hose clamp and nozzle.
30. Install swivel to hose. Follow swivel manufacturer instructions.
31. Install nozzle to swivel. Follow nozzle manufacturer instructions.
32. Check for correct nozzle cradle/hook type (vapor, non-vapor, etc.).
33. Do not turn onAC power. Applying power now voids warranty. When
installation is complete, a GilbarcoAuthorized Service Contractor must perform a
start-up.
WARNING
Hose pulled away from pump/
dispenser exposes fuel.
Explosion and fire could result
in severe injury or death.
Installation of breakaways is
required by NFPA 30A
$
$
TAXESINCLUDED
PRICE/GALLON
GALLONS
THISSALE
$
$
TAXESINCLUDED
PRICE/GALLON
GALLONS
THISSALE
1. REMOVE NOZZLE PLACE IN CAR FULE TANK.
2. LIFT HOOK ''ON'' WAIT UNTIL COMPUTER
RESETS TO ZERO.
3. OPERATE NOZZLE FOR GASOLINE.
4. AFTER COMPLETING DELIVERY. LOWERHOOK
''OFF'' AND HANG NOZZLE UP.
DONOT LOWER HOOK ''OFF'' UNTIL YOU
FINISHEDDELIVERY.
AFTERARRANGING PURCHASE WITH CASHER
PROCEEDAS FOLLOWS.
NOSMOKING-SHUT OFF ENGINE
CAUTION
Unleaded Super
7
4
1
8
5
2
0
9
6
3
Super
93
Plus
91
Breakaway on High-Hose
Breakaway on Low-Hose LegacySeries
Swivel
Nozzle
Hose

1995 Gilbarco Inc. • P.O. Box 22087, 7300 W. Friendly Ave., Greensboro, NC 27420 • Phone [phone], Fax [phone], Telex 4949970
MDE-2530H 03/95 Printed in USA
®