Gingerway GW-4361 User manual

Gingerway Technologies Co.,Ltd
Enjoy the Life
Dear users, sincerely thank you for choosing our products. For your convenience
of installing and using this product, please read this manual carefully before use.
GW-4361 is a high-end smart thermostat that with large graphic LCD screen and
capacitive touch keys.
GW-4361 can control the fan coil unit, air conditioner, the fan of heating device,
air valve, air valve, heater and other equipments. It can be used independently,
can also connect to Z-Ginger® wireless network to realize the intelligent control.
Descriptions
Touch Key Thermostat Instruction Manual
GW-4361
Illustration
Display area:
A. RT(room temperature) / SET(setting temperature): Thermostat displays room
temperature by default, marked by "RT". After press the "Up" or "Down" key, it will
enter temperature setting interface. The displayed current setting temperature
marked by "SET".
B. Fan Speed: With 4 types of fan speed: LOW, MEDIUM, HIGH, AUTO.
For AUTO type, when the room temperature differs 1℃from your setting
temperature, the thermostat will automatically change to low fan speed; when
the room temperature di󰀨ers 2℃ from your setting temperature, the themostate
will automatically change to medium fan speed; When the difference between
room temperature and your setting temperature over 3℃, the themostate will
automatically change to high fan speed.
C. Mode: With 3 modes: Cooling, Heating, Ventilating. In the ventilating mode,
the fan speed without the option of "AUTO".
D. Timer: Set a timing to start up or shut down the thermostat. In o󰀨-state, you
can set a timming to start up the thermostat; In on-state, you can set a timing to
shut down the thermostat.
E. Sleep Mode / P(low temperature protection):
At on-state, you can set the thermostat to sleep mode: Under cooling or heating
mode, the thermostat reverse heating or cooling 1℃in the 1st hour, and then
reverse heating or cooling 1℃ in the 2nd hour. Then keep it to the end of sleep,
give you a comfortable sleep environment.
At o󰀨-state, you can set the thermostat to low temperature protection: when the
room temperature is below 5℃, the thermostat automatically start heating; When
the room temperature rises to 7℃, the thermostat will automatically stop heating.
1. Z-Ginger® full digital two-way communication wireless network.
2. Supports the cooling, heating or ventilating equipments of 2-pipe or 4-pipe and
three-speed fan, t 7 types of heating/cooling equipments.
3. Supports independent control, also supports Z-Ginger® protocol wireless
network control.
4. With large graphic LCD, support multi-languages display.
5. With high sensitivity capacitance backlit touch keys.
6. Detect and display the environmental temperature.
7. Cooling/heating/ventilating mode for your selection.
8. Manual(3 speed) / automatic fan speed for your selection.
9. Power o󰀨 memory function.
10.Timer on/o󰀨 and sleep function.
11. Low temperature protection function.
12. Ultra-low power design, be suitable for universal power supply.
Main Features and Functions
Product Wiring Diagram
Scope of Application
Being used in hotel, commercial building and factory to control the fan coil unit, air
conditioner, heater and other equipments.
A.
RT(room temperature)
SET(setting temperature)
B. Fan Speed
C. Mode
D. Timer
E.
Sleep Mode /
P(low temperature protection)
F. ON-OFF /
Bind key
G.
Mode setting/
Timer setting
H.
Fan speed setting/
Sleep mode/
Low temperature protection
Keys Area :
F. ON-OFF / Bind key: Short press this key to turn on/o󰀨 the thermostat; Long
press it for 12 seconds to start to bind with gateway or controllers.
G. Mode setting / Timer setting: Short press this key to switch the thermostat
mode; Long press it for 5 seconds, then you can set the timing to start up or shut
down the thermostat.
H. Fan Speed / Low temperature protection / Sleep mode setting: Short press
this key to switch the thermostat fan speed; Long press it for 5 seconds, can set
to low temperature protection when the thermostat is on, and can set to sleep
mode when the thermostat is o󰀨.
I. Up key: By default, short press it to turn up the setting temperature; When in
timer setting state, short press it to increase the timing time.
J. Down key: By default, short press it to turn down the setting termerature;
When in timer setting state, short press it to decrease the timing time.
Open the thermostat, there are 3 selectable jumpers at the back of thermostat top
panel. You can choose the device type of thermostat via the jumpers:
0 (V3F3S): Default configuration (the jumpers are not welded), control 3-wire
electric valve and 3-speed fan. After the temperature reached, the valve and fan
will be shut down;
1 (V0F2): Control the electric air valve or electric air vent;
2 (V2F3C): Contrl 2-wire electric valve and 3-speed fan. After the temperature
reached, the electric valve will be shut down, the fan will continue to run;
3 (V2F3S): Control 2-wire electric valve and 3-speed fan. After the temperature
reached, the electric valve and the fan will be shut down;
4 (V3F3C): Control 3-wire electric valve and 3-speed fan. After the temperature
reached, the electric valve will be shut down, the fan will continue to run;
5 (V4F3C): Apply to 4-pipe system, to contyrol electric cold and heat valve(2-wire
valve) and 3-speed fan. After the temperature reached, the electric valve will be
shut down, the fan will continue to run;
6 (V4F3H): Control electric cooling and heating valves(2-wire valve) and 3-speed
fan. After the temperature reached, the electric valve will be shut down. the fan
will continue to run in Cooling mode. If in Heating mode, only control the electric
valve, the fan is closed at any time;
7 (HEATER): Being used for controlling oor heater. Only with Heating mode, the
thermostat will automatically enter into low termperature protection status after it
turned o󰀨, the temperature of low temperature protection is 15℃.
FAN
LN
L
M
H
ON
OFF
V A L V E
3-SPEED F A N
100 ～ 240VAC 50/60HZ
0 (V3F3S)
4 (V3F3C)
I.
Up key
J.
Down key
V1.2
LN
L
M
FAN V A L V E
100 ～ 240VAC 50/60HZ
1 (V0F2)

Power Supply 100 ～ 240VAC 50/60HZ
Standby consumption: <0.5W
Maximum consumption: <2W
Outputs Up to 5 relays
Load current: rated current 1A, surge current 3A
User Interface 5 backlit capacitive touch keys
Backlit 128*64 B/W graphic LCD
RF
Frequency: 433MHz(315M, 868M, 915M are customizable)
Transmit power: 10dbm
Receiving sensitivity ≤-105dbm
Temperature
Setting temperature: 5-35℃
Environmental temperature: 0-50℃
Precision: ±1℃
Probe: NTC
Installation CCC(86mm*86mm)
CE(86mm*86mm)
Wiring 2 power-supply wirings
5 ways output wirings
Cross-sectional area of conductor:
1 * 1.0 mm² ~ 1 * 2.5 m²
Timer Minimum programming interval: 1 hour
Maximum programming interval: 12 hours
Operating Environment Environmental temperature: 0℃to 50 ℃
Relative humidity: 10% to 90%
Certication
CE Mark Low Voltage
CE Mark EMC
CE RADIO
Shell 94-V0 PC
Dimensions & Weight W 86mm x L 86mm x H 14.7mm (Front Panel)
W 86mm x L 86mm x H 36.7mm (Total)
Weight: 155g
Technical parameters
Restore factory settings
1.Turn o󰀨 the power of smart thermostat.
2.As soon as the power, long press the leftmost and righmost
keys(ON-OFF key and Down key) at the same time for 10
seconds.
3.The smart thermostat will be restored to factory settings.
Binding
Long press the ON-OFF key for 12 seconds, start to bind with
main controllers, such as gateway, remote controller, etc.
Timer setting
Long press the "M/Timer" key for 5 seconds, the timer will be
displayed. Then long press the "M/Timer" key again, the timer
will be cancelled. Press the "Up" and "Down" keys can adjust
the timing.
In o󰀨-state, you can set a timming to start up the thermostat;
In on-state, you can set a timing to shut down the thermostat.
Low temperature protection
In o󰀨-state, long press the "fan" key for 5 seconds can set the
thermostat to low temperature protection mode, long press
the "fan" key once again can cancel it.
Low temperature protection: When the room temperature
is below 5℃, the thermostat will automatically start heating;
When the room temperature rises to 7℃, the thermostat will
automatically stop heating.
Sleep mode setting
In on-state, long press the "fan" key for 5 seconds can set the
thermostat to sleep mode, long press the "fan" key once again
can canel the sleep mode.
Sleep mode: Under cooling or heating mode, the thermostat
reverse heating or cooling 1℃in the 1st hour, and then
reverse heating or cooling 1℃ in the 2nd hour. Then keep it to
the end of sleep, give you a comfortable sleep environment.
Usage
FAN
LN
L
M
H
ON V A L V E
3-SPEED F A N
100 ～ 240VAC 50/60HZ
2 (V2F3C)
3 (V2F3S)
FAN
LN
L
M
H
ON
OFF HOT
V A L V E
3-SPEED F A N
100 ～ 240VAC 50/60HZ
COOL
V A L V E
5 (V4F3C)
6 (V4F3H)
Warranty Terms
Gingerway products are guaranteed for 2 years since the date of purchase.
During the warranty period, if Gingerway products malfunction(not contain articial
damages) under normal circumstances, they can be free repaired or exchanged
at local dealer with the purchase invoice.
1. If due to quality failure during the warranty period, the maintenance is free in
rst year, only the component cost will be charged in the second year.
2. Disassembling Gingerway product components without the permission of
our company or the local client center, our company will no longer bear the free
warranty responsibility .
Note: Shenzhen Gingerway Technologies Co., Ltd reserves the right of final
explanation for above terms.
0678
Shenzhen Gingerway Technologies Co., Ltd.
Address: 3-Floor, Building A6, Xingye Industrial Park, Zhongshanyuan No.2 Road,
Nanshan District. Shenzhen, Guangdong, China.
Tel :[phone] Fax :[phone]
Website: www.gingerway.com
1. Please hire professional electrician to install or disassemble this product. The
power must be cut o󰀨 before installing or disassembling.
2. This product is forbidden to be installed in outdoors, bathroom and other humid
environments.
3. The wiring must be in accordance with instruction manual, otherwise the
products may be damaged.
Notice
(7)
ON
1 2 3
7(HEATER)
LN
ON
OFF
V A L V E
100 ～ 240VAC 50/60HZ