Glacier Start GLC-GS-CHR-T5 User manual

Dodge/Chrysler Regular Key
GLC-GS-CHR-T5
Installation Guide
PANIC

GS-CHR-T5
1 and 2-way LED Remote Starter Page 1
VEHICLE FIT GUIDE
VEHICLE
200
300-300C
Aspen
Crossre
PT Cruiser
Sebring
2011-2012
2005-2007
2007-2009
2008
2008-2010
2007
2008-2010
Avenger
Caliber
2008-2012
2007
Charger
Dakota
2006-2007
2007-2012
Nitro
Ram
2007-2011
2006-2007
Durango
Magnum
2008-2012
2007-2009
2005-2008
2008
Commander
Compass
2006-2007
2007
Grand Cherokee
Liberty
2005-2007
2008-2012
Patriot
Wrangler
2008-2012
2007-2012
2007-2012
Lock
Arm
Unlock
Disarm
Hatch(open)
RAP Disable
Trunk(open)
Tachometer
Door Status
Hand Brake
Trunk Status
Connection
CHRYSLER
DODGE
JEEP
A
B
A
A
B
B
A
A
B
A
B
A
A
B
A
B
A
B
B
A
B
A
A
A
Foot Brake

GS-CHR-T5
1 and 2-way LED Remote Starter
FM
2-W
Page 2
A.WIRING DIAGRAM
PANIC
Valet Switch
Hood Pin
Vehicle Brown/White
Parking Lights(-)
Pink
Ignition(+)
Gray
Hood Pin(-)
Yellow
Ignition(+)
Yellow
Ignition(+)
EVO-ALL
Cut Yellow Loop when
installing on an automatic
transmission
Green/Red
Purple Wire
DO NOT CONNECT ON A JEEP WRANGLER
EVO-ALL 6 Pin
Red Connector
EVO-ALL 5 Pin
White Connector
Ignition Barrel
THAR-CHR5
4 Pin Data Link
Connector
Antenna

GS-CHR-T5
1 and 2-way LED Remote Starter
FM
2-W
Page 3
B.WIRING DIAGRAM
Valet Switch
Hood Pin
Vehicle Brown/White
Parking Lights(-)
Yellow/Black - Programmable.
Set for Ignition using Function 2
on Page 6.
Pink
Ignition(+)
Gray
Hood Pin(-)
Yellow
Ignition(+)
Yellow
Ignition(+)
EVO-ALL
Cut Yellow Loop when
installing on an automatic
transmission
Green/Red
EVO-ALL 6 Pin
Red Connector
EVO-ALL 5 Pin
White Connector
Ignition Barrel
THAR-CHR5
PANIC
MUX 2nd Ignition
(+)Starter
(+)12V
If the vehicle
does not have
a (+)Starter
wire, use
connection A.
White/Blue
White/Red
4 Pin Data Link
Connector
Antenna
4 Pin Data Link
Connector
Ensure Jumper on the front
of the Glacier module is in
the left(+) position.
+ Polarity
750 mA max - Polarity 750 mA max

PANIC
GS-CHR-T5
1 and 2-way LED Remote Starter Page 4
Programming
Programming the EVO-ALL The EVO-ALL must be programmed before the Glacier Start transmitters can be programmed.
Step 4
Press the Lock button on the OEM
remote or hit the programming
button on the EVO-CHR
OR
With
OEM alarm
Without
OEM alarm
EVO-ALL
Step 1 Step 2
Press and hold
the programming
button.
Insert the remaining
connectors
EVO-ALL
Insert the 4 Pin
Data Link
Connector
The LED will
alternate between
BLUE, YELLOW
and RED.
EVO-ALL
Release the
programming
button when the
LED is Blue.
If the LED is not
solid Blue,
disconnect the
4 Pin Data Link
Connector and go
back to step 1.
EVO-ALL
Step 3
I G N
Turn the Ignition to
the ON/Run
position.
O F F
Turn the ignition
OFF.
The Blue LED will
continue to ash
rapidly.
The Blue LED will
ash rapidly. EVO-ALL
The Blue LED will
turn off.
The Module
is now
Programmed.

Page 5
GS-CHR-T5
1 and 2-way LED Remote Starter
Programming
Programming Remote Transmitter(s)
1 2 3 4
The System can learn up to a maximum of 4 transmitters. A single
transmitter can be stored in more than 1 memory slot. When a 5th
transmitter is learned the 1st remote is erased.
I G N
Step
1
Step
2
Turn Ignition On. O F F
Place unit into Valet Mode before programming transmitters See bottom of page for instructions.
Press and hold valet
switch until antenna
LED ashes rapidly.
Step
3
1x
Press and release the
valet switch once.
Step
4
Press and release
the brake pedal
once.
Step
5
Press the LOCK
button on each
transmitter that you
want programmed.
Step
6
Press and release
the brake pedal once.
Turn Ignition off.
A.
B.
Programming
Ready Mode - For Manual Transmission
12 3
4 5 6
&
1 2 3 4 5 6
O F F
Ensure all doors are
closed and the vehicle is
in neutral.
While the engine is
running, engage the
Parking Brake.
Release the Brake Pedal Press the START button. The
parking lights will ash once
and then stay on.
Turn the ignition off and
remove the key.
Exit the vehicle and
close all the doors. The
engine will shut off once
all the doors are closed.
Programming
To Disable Ready Mode
STANDARD
• Open any door(s)
• Open the hood
• Disengage the parking brake
With Neutral Safety Switch
• Transmission not in neutral position
• Open the hood
• Disengage the parking brake
Note: If the parking lights
ash 3 times when remote
starting, Ready Mode is not
enabled.
Programming
Enter/Exit Valet Mode
I G N
Turn Ignition On.
A. B.
C.
Insert the
key and
turn it to
the ignition
(Run/On)
position.
Within 10
seconds
press and
release the
Valet switch 3
times.
The LED
will turn ON
solid blue
and remain
ON.
Programming
Cold Start Mode
To Enable
Press UNLOCK
and START buttons
simultaneously for 1
second until the park
lights ash once.
To Disable
- Press UNLOCK and START simultaneously
- Put the Remote Starter into Valet Mode
- Remote Start the vehicle
- Open the hood
- Press the brake pedal
- Turn the key to the ignition position
- Disable Ready Mode (manual transmission)
Programming
Remote Start / Alarm Diagnostics
Remote Starter Diagnostics
Parking Light Flashes - Before Starting
3x - Ready Mode is disabled
4x - Valet Mode Activated (The LED on the
antenna is on)
5x - Hood open
Parking Light Flashes - After Starting
1x - Normal Stop (Park brake, Brake)
3x - Runtime expired or shut down by remote
4x - No tachometer signal
5x - Hood open
6x - Over crank threshold (8 seconds)
Alarm Diagnostics
Parking Light Flashes - After Disarm
3x - Door open
4x - Shock sensor
5x - Hood open
6x - Trunk open
7x - Auxilliary IN
8x - Tilt Sensor
9x - Ignition
D.
O F F
Turn Ignition off.
3x
12 3
4 5 6
&

Page 6
GS-CHR-T5
1 and 2-way LED Remote Starter
Programming
Programming Options Options in BOLD RED are default settings.
I G N
Turn Ignition On.
1 2 3 4 5 6
Press and hold valet
switch until antenna
LED ashes rapidly.
Press and release the
valet switch 1-37 times
for the desired channel.
Press and release
the brake pedal
once.
Press Lock(1), Unlock(2),
Trunk(3), or Start(4) on a
programmed remote to
select the mode.
1 2
3 4 O F F
Turn Ignition off.
The Channel will reset.
Functions
1
2
3
4
5
6
Add Remote
Ignion Conguraon
Tachless Sensivity
Run Time
Alarm Opons
Door Lock Before And Aer
Remote Start
Mode 1
Button 1
Program Driver 1
Ignion
Increase Crank Time
Gas: 15 Minutes
Diesel: 30 Minutes
Sets Funcons #7, #9,
#14 & #15 as default
Disabled
7
8
9
10
11
12
Safety Locks
Unlock Pulse Time
Acve or Passive Alarm
& Starter Kill
Starter Kill Output
Mode 2
Button 2
Program Driver
Mode 3
Button 3
Mulvehicle Programming
Accessory
+++++
Gas: 7 Minutes
Diesel: 14 Minutes
Enables Funcons #7, #9,
#14 & #15 at mode 2
Start(Default)
++++(Default)
Gas: 3 Minutes
Diesel: 6 Minutes
Unlock before remote start
& Lock aer remote start Lock aer remote start
Disabled
Unlock and relock aer
shut down
Mode 4
Button 4
+++
Mode 5
Button 1 & 2
++
Relock 10 seconds aer
shut down
Lock aer foot brake & un-
lock aer key is turned o Unlock aer key is turned o
Single 0.25 sec. Double 0.25 sec. Single 4.0 sec. Single 2.5 sec. Single 1.5 sec.
Conrmaon
Acve - Press Lock
to acvate the Alarm
and Starter Kill
Passive(Lock Disabled)
Arm alarm & acvate
starter kill 30 seconds
aer door is closed
Passive(Lock Enabled)
Arm alarm, acvate
starter kill & lock door
when the door is closed
Starter kill & An grind An Grind only Relay normally open
1st Lock/Unlock - Silent
2nd Lock/Unlock - Sound
----------------------------------
Antenna LED Acve
Lock/Unlock
Sound Always
Antenna LED
Disabled
Antenna LED
Disabled with
ignion
13
14
Sound Conrmaon
Conrmaon Pulse
Horn Only
Long Short
Alarm & Starter Opons Alarm disabled
Remote starter enabled
Alarm & Remote starter
enabled
Alarm enabled, Remote
starter disabled
Disabled
(Unlock Signal)
Automacally Lock and
rearm alarm if door(s) are
not opened aer 30 seconds
15 Smart Door Lock
Relocking and Alarm
Rearming
Lock when starter kill arms Arm pulse only when the
alarm is disarmed
16 Cold Start Timer 3 hours/Runme 1.5 hours/Runme 3 hours/5 Minutes 1.5 hours/5 minutes Cold Time O
17 Domelight Delay Disabled
Enable-Ignore door trigger
(dome light) when arming or
Remote Starng
18 Diesel Mode Disabled
Enable (20 seconds)
Delay between Ignion
power up and Starter crank
Enable (10 seconds)
Delay between Ignion
power up and Starter crank
19 Turbo Timer Disabled Run 2 minutes Run 4 minutes
20
Engine Supervision:
-Tachless-
-Analog Tach-
-Tach Data-Link-
Tachless on crank and super-
vision Tach Data-Link
or Analogic aer.
Tachless Only
(automac transmission only)
Start (crank) 8 sec on
tachless
(automac transmission
only)
Start (Crank) 8 sec +
Supervision by Data-Link
Tach
(Data interface required)
Single 0.75 sec.
21 Start Aempts 2
Tach Data-Link only
(Data interface
required)
1 3
22
23
Transmier Start/Stop
Funcon
Start(buon 4) 1 sec.
Stop(AUX-buon 4) 1 sec
Start(buon 4) 3 sec.
Stop(AUX-buon 4) 1 sec
Opon alarm acve
2-way remote Baery saver
Start(AUX-buon 4) 1 sec.
Stop(buon 4) 1 sec.
Master Reset Rest All Opons to
Default
Mode 6
Button 3 & 4

Page 7
GS-CHR-T5
1 and 2-way LED Remote Starter
Programming
Programming Options Continued Options in BOLD RED are default settings.
Functions
Push To Start
Conguraon
Auxilliary 1 Output
(AUX-LOCK)
Hybrid Mode
Auxilliary 1 Output
(AUX-UNLOCK)
Not Supported
Alarm Duraon
Mode 1
Button 1
Disabled
Sliding Doors
Data Link Only
Gas/Diesel Vehicle
30 Seconds
Valet Code
Not Supported
Mode 2
Button 2
Applicaon 1
Mode 3
Button 3
Applicaon 2, Turn OFF the
engine when the door is
open. See www.ifar.ca for
the installaon guide
Hybrid Vehicle
60 Seconds 120 Seconds
Ignion ON, Valet
buon x3 mes
Mode 4
Button 4
Mode 5
Button 1 & 2
Ignion ON, Valet buon x3
mes and x1 me 3 seconds
36
35
34
33
32
31
30
29
28
27
26
25
24
37
Applicaon 3, Turn OFF the
engine when the foot brake
is pressed
Sliding Doors
Data Link Only
Ignion ON, Valet buon x4
mes and x1 me 3 seconds
Ignion ON, Valet buon x5
mes and x1 me 3 seconds
Ignion ON, Valet buon x6
mes and x1 me 3 seconds
Ignion ON, Valet buon x7
mes and x1 me 3 seconds
Ground Out Shut down 1 second aer
remote start runme
Shut down 3 seconds aer
remote start runme
Manual Transmission
Ready Mode Acvaon
Acvated by the remote
starter remote
Automacally acvated
by hand brake and foot
brake(ON). Not funconal
on tachless. Tach must be
connected
Trunk Output Pulse 0.5 seconds Pulse 2.5 seconds Unlock before trunk pulse
0.5 sec
Door unlock Special
Applicaon No Special Applicaon Acvate vehicle ignion
at Unlock
Acvate vehicle ignion and
accessory at Unlock
Valet Mode
Conguraon
By remote: Lock &
Unlock or valet buon
By remote: AUX-Lock &
Unlock or valet buon By valet buon only
Security Conguraon No Special Applicaon
Security ON: Shutdown
Engine if the door is opened
before Unlock is pressed.
(Door trigger required)
Mode 6
Button 3 & 4