Global Telecom LTE TITAN2000 Series User manual

Quick Start Guide
GLOBAL TELECOM LTE TITAN2000 SERIES

Contents
What’s in the Box ............................................................................................... 4
Connect the TITAN2000 Adapter to external router/PC................................................ 5
Determine Where to Mount Your Adapter............................................................... 6
Mount the Adapter ............................................................................................. 7
LED Lights Reference ......................................................................................... 10
Customer Support .............................................................................................. 11
3

What’s in the Box
TITAN2000 LTE ADAPTER Mounting Plate Powered Ethernet Cable
Suctions
Cups
ALCOHOL WIPE
Alcohol Wipe
Screws and Anchors

Connect the LTE TITAN2000 Adapter to aPC
or aRouter
STEP 2
Remove the front panel at the bottom of the LTE
TITAN2000 Adapter. To do so, use your
fingernail to lift the lever at the bottom of the
front panel. Then gently push down in the
middle of the front of the panel to slide it off.
Next, connect one end of the powered ethernet
cord to the LTE TITAN2000 Adapter and the
other end to the LTE connector on the back of
the Router/PC
LTE TITAN2000
LT EWA N
Router
6

Determine Where to Mount Your Adapter
For the best 4.5G signal, the adapter should be placed in an area with good
cellular reception. You can test the reception in various areas using either
the signal LEDs on the front of the adapter, or using the mobile app.
Placement recommendations:
■Mount the adapter in awindow, if possible.
■Mount the adapter on the highest floor of the building possible.
■Do not place the adapter within five feet of alarge metal object,
like awater heater or refrigerator.
■Try the adapter in different places within aroom, in different rooms,
and on different sides of abuilding.
To test the signal in different locations, simply move the Connect 4G adapter
and wait for approximately 10 seconds. The adapter can be connected with a
cable up to 250'long (not provided).
STEP 3
7

8
First, clean the surface with the
included alcohol wipes. Do not
use household cleaners.
Mount the Adapter
STEP 4
Next,for adhesive tape installation,
remove the red side of the included
adhesive strips and adhere to the
one side of the mounting plate, as
pictured. Repeat for the other side.
Finally, remove the black side of both
adhesive strips. Press the mounting
plate against the window in the desired
position and hold it for 30 seconds.
Wait 1hour before hanging the adapter
on the mounting bracket.
Window Mounting Instructions-Adhesive Tape

8
First, clean the surface with the
included alcohol wipes. Do not
use household cleaners.
Mount the Adapter
STEP 4
Next,for Suction cups installation,
remove the screws from suction
cups.
Finally, alight the suction cups with
holes using included screws and
tighten the suctions cups. Press the
mounting plate against the window in
the desired position and hold it for 30
seconds.
Wait 1hour before hanging the adapter
on the mounting bracket.
Window Mounting Instructions-Suction Cups
Suction Cups

9
Insert the anchors into the holes.
Place the mounting bracket and
insert the screws into the anchors.
Drywall MountingInstructions
Hold the mount to the wall in its desired Use adrill to make holes for the anchors.
place and mark the holes.

LED Lights Reference
LTE –Indicates signal strength, from 1to 5bars
ETH –Indicates the adapter has an ethernet link via LTE
SYS –Indicates the adapter is powered on, may blink fast
during startup, slow blink means critical error
SIM –Indicates the adapter has avalid SIM card installed
10

Customer Support
Need help? Global Telecom has awealth of available
resources to help if you need assistance.
Support Articles and User Manuals. Access our comprehensive knowledge base
at [e-mail]
11

For warranty, safety, and other legal information,
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference that may cause undesired operation.
GLOBAL TELECOM