Gobosource ECO Spot 150 User manual

ECO Spot 150/250 User Manual
Page 4 Copyright © 2011 Globus New Media LLC Page 4
Electrical Specifications
Voltage: 110-130V, 50-60Hz, 0.8A, 80W (US-Version)
Ambient Operating Temp. : -13 to 104°F (-25 to 40°C)
Ballast type: Magnetic, not dimmable
Mechanical Specifications
Fixture Body: 7.5in x 5.5in x 17.7in (190mm x 140mm x 450mm)
Total Length: 22in (560mm)
Yoke Base: 6.4in x 7.8in (163 x 198mm)
Yoke Height: 7.5in ( 190mm) (from base to center)
Total Height: 10in ( 254mm) (from base to top)
Weight: ES-150: 18lbs (8.2kg), ES-250: 22lbs (10kg)
Gobo Types and Dimensions
Metal or Glass Gobos and Dichroic filters
Fits regular M-size gobos (OD66mm x ID48mm)
Outer Diameter (OD): 66mm (2.6 in)
Max. Image Diameter (ID): 50mm (1.9 in)
Max Thickness: 4mm (0.16 in)
Optical
Lens Options: Standard 19 degree (included), optional lenses in development
Typ. Projection Size = Projection Distance / 3
(for example, at a distance of 12 ft. the resulting image size is 4 ft.)
Typical Range
The range varies greatly with the application and ambient light situation
ES-150: ES-250:
6 to 42 ft in bright environments 9 to 64 ft in bright environments
up to 88 ft in dim environments up to 112 ft in dim environments
up to 140 ft in dark environments up to 200 ft in dark environments
All rights reserved, Globus New Media is not liable for errors or omissions.
ECO Spot 150/250 User Manual
Copyright © 2011 Globus New Media LLC Page 1
Thank you for choosing an ECO Spot™ Gobo projector. This unit is
equipped with a fan cooled discharge light bulb. Please read this
manual before installing or operating this fixture, follow the safety
precautions listed below and observe all warnings.
Package Contents
 Projector with power cord and integrated gobo holder and rotator
 Light Bulb
Safety Information
Handling Instructions
ECO Spot™ 150/250 User Manual
Do not look directly into the lamp, it can result in eye damage.
This product is not for household use, it presents risks of severe injury or death due
to fire and burn hazards, electric shock, lamp explosion and falls.
Light fixtures should be installed and maintained only by qualified personnel with
experience in lighting equipment and general electrical experience.
Always disconnect the unit from power and allow cooling down for 20 minutes
before servicing.
Place your fixture at a suitable place with good air flow and keep flammable materials
away.
Minimum distance to flammable materials = 1ft. (0.3m).
Minimum distance to illuminated surfaces = 3.3ft. (1.0m).
Provide a minimum clearance of 4in. (10cm) around air vents.
Don’t touch the hot surface during operation, use gloves if necessary.
Replace Lamps only with the same type other lamps may cause damage.
Always ground (earth) the fixture electrically.
Use only a power source that complies with local building and electrical codes and
has both, overload and ground-fault protection.
Do not use the fixture if the power cable or power plug is in any way damaged,
defective or wet, or if they show signs of overheating.
When suspending the fixture above ground level, verify that the structure can hold at
least 10 times the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use
approved means of secondary attachment such as a safety cable.
Please unpack and carefully check for damage caused during transportation.
Make sure there are no flammable materials close to the fixture.
Do not touch the light bulb with bare hands, the oils can damage the bulb and can
cause failure or explosion of the bulb.
After turning off the projector, it may take up to 15 minutes to restart.
Use only genuine spare parts for part replacement.

ECO Spot 150/250 User Manual
Page 2 Copyright © 2011 Globus New Media LLC Page 2
Warranty
One Year from Date of Purchase
Contact
Globus New Media LLC
Tel [phone] or 1-408-416-4444
Fax [phone]
www.globusnewmedia.com
Focusing
Power up the projector by pressing the switch next to the power cable in the back.
Turn on the gobo rotator with the other switch in the back and turn it off when the
gobo projects in the desired position (optional).
Focus the projection by twisting the lens in and out until the image is well focused.
When used for the first time, the lens will often need to be twisted many rotations to
reach the focusing point. This can take a few minutes.
Gobo Rotator
Gobo Replacement (see illustration below)
Unplug the power cord and let the projector cool down for 20min. Use caution, the
housing and light bulb may still be hot.
Turn on and off the gobo rotator with the switch on the back plate.
Turn on/off repeatedly to switch the rotating direction.
There are no controls for rotating speed.
Unscrew the thumbscrews to remove the front cover with the projection lens.
The gobo rotator with the gobo holder is now exposed.
Carefully pull out the gobo holder.
Unscrew the large ring that sits in front of the gobo.
The old gobo is now accessible, carefully remove and replace it.
Screw back in the large ring, so that it just touches the gobo, don’t tighten it,
otherwise it will be hard to remove it later.
Replace the front cover.
Power on the projector and refocus the image by screwing the projection lens in or
out.
ECO Spot 150/250 User Manual
Copyright © 2011 Globus New Media LLC Page 3
Lamp Replacement
Recommended Replacement Lamps:
ES-150 ES-250
Osram HCI-T 150/943 NDL PB Philips MSD 250/2 30H
Base: G12 Base: GY9.5
Color temperature: 4,200 Kelvin Color temperature: 8,000 Kelvin
Color Rendering Index CRI: 96 Color Rendering Index CRI: 80
Luminous Flux 14,500lm Luminous Flux 18,000lm
Average Bulb Life: 12,000h Average Bulb Life: 3,000h
Unplug the power cord and let the projector cool down for 20min. Use caution, the
housing and light bulb may still be hot.
Unscrew the thumbscrews to remove the front cover with the projection lens.
The gobo rotator with the gobo holder is now exposed.
Carefully pull out the gobo holder.
The lamp is now exposed. Remove it by gently pulling it out of the socket. Reverse
this procedure for the new lamp. Do not touch the light bulb with bare hands, the oils
can damage the bulb.

Replace the gobo rotator and the front cover.