Goclever Navio 515 User manual

OWNER’S MANUAL
INSTRUKCJA OBSŁUGI
www.goclever.com

IMPORTANT
Satellite signals are required for this product to funcon in Naviga-
on Mode. There may be occasions within your home or building
when the signal strength is limited and Navigaon Mode may not
be possible. This is quite normal for products of this type. You can
check the number of satellite signals that the unit is receiving and the
strength of those signals by viewing the GPS Receiver page, see "GPS
Receiver”.
SAFETY
The Global Posioning System (GPS) is a satellite based system that
provides locaon and ming informaon around the globe. GPS is
operated and controlled under the sole responsibility of the Gover-
nment of the United States of America, who are responsible for its
availability and accuracy.
Using Your navigaon in the Car.
When using while driving it is essenal that you drive with due care
and aenon.
Never modify the sengs or program your navigaon while driving.
Only look at the map when it is safe to do so. Only follow the instruc-
ons when the road regulaons allow you to do so.
When mounng the device in your car make sure that it does not
obscure your view or impede the operaon of any driving controls.
BATTERY
Your navigaon uses a Li-ion baery. Do not use it in humid, wet
or corrosive environments. Do not operate or store your device in
high temperatures (>60 C) or in direct sun light. Do not store in a
microwave or pressurised container. Do not pierce or break the bae-
ry casing.
Failure to follow these cauons will invalidate the warranty and may
cause the baery to become hot, explode or ignite and

cause injury or damage. The Li-ion baery contained in this
unit must be recycled or disposed of properly. Do not dispose of in
household waste or burn.
GETTING STARTED
Please make sure that you read all of the informaon contained
within this user guide before contacng the customer helpline.
In the Box
In the box you will nd
• Satellite Navigaon System GOCLEVER NAVIO 515
• USB DC power lead with 5V car adapter
• Car Mounng Cradle
• USB cable to connect to your PC
• User Manuals
Control’s Posion

Charging the Baery
Before using your device the baery will need to be charged. To
maximize the life of the baery the rst charge must fully charge the
baery. We recommend that you charge the unit for 2 hours in order
to achieve the full charge. Subsequent charge mes may be shorter.
Plug the mains adapter into the socket on the rear of the unit USB
port and switch it on.
The red charging indicator on the front of the unit will light. When
the unit is fully charged the red indicator is exnguished.
We recommend that when you use navigaon in your car, that you
always use the 12V cigaree adapter in order to maintain the baery
level.
Installing the micro SD Memory Card(Oponal)
Once the card is installed it does not need to be removed. If you need
to remove the card, switch the unit o rst, push the card in and it
will eject from the slot.
When re-installing it can only be ed one way - contacts towards
you and the cut-o corner at the top as shown. Slide the card in and
push fully home so that it clicks in place.
It can support up to 8GB micro SD card.
Mounng the Unit in your Car
WARNING!
Device must be mounted in a locaon that does not obscure the dri-
vers vision, impede use of the car’s controls or impede the operaon
of the car’s airbags. Screw the car mount into the back of the unit as
shown below.
4
Charging the Battery
Before using yourdevice the battery will need to be charged. To maximize the
life of the battery the rst charge must fully charge the battery. We recommend
that you charge the unit for 5 hours in order to achieve the full charge. Subsequent
charge times may be shorter. Plug the mains adapter into the socket on the
rear of the unit USB port.
Plug the adapter into the mains supply and switch it on.
The red charging indicator on the front of the unit will light. When the unit is fully
charged the red indicator is extinguished.
We recommend that when you use navigation in your car, that you always use the
12V cigarette adapter in order to maintain the battery level.
Installing the micro SD Memory Card(Optional)
Once the card is installed it does not need to be removed. If you need to remove
the card, switch the unit off rst, push the card in and it will eject from the slot.
When re-installing it can only be tted one way - contacts towards you and the cut-off
corner at the top as shown. Slide the card in and push fully home so that it clicks in
place.
It can support up to 8GB micro SD card.
Mounting the Unit in your Car
WARNING!
Device must be mounted in a location that does not obscure the drivers vision, impede
use of the car's controls or impede the operation of the car's airbags. Screw the car
mount into the back of the unit as shown below.
Car Adapter
When using your navigation in the car we recommend that you always use
the car adapter to power the unit, especially on long journeys. Plug the car adapter
into the socket marked USB port on the rear of the unit. Plug the other end on
the adapter into the car's 12V accessory socket. The illustration on the next
Manual-N90-英语.indd 4 2010-8-20 17:01:51

Car Adapter
When using your naviga on in the car we recommend that you
always use the car adapter to power the unit, especially on long jo-
urneys. Plug the car adapter into the socket marked USB port on the
rear of the unit. Plug the other end on the adapter into the car’s 12V
accessory socket. The illustra on on the next page shows a typical
installa on. If possible  x the power cable so that it does
not obscure instruments or controls and does not cause a tripping
hazard.
Switching On
Firstly The System logo is displayed.
5
Switching On
Firstly The System logo is displayed.
seodt it ah tose l bacr ewopeh txfielbissopf I.noi tal latsnilacipytaswohsegap
not obscure instruments or controls and does not cause a tripping hazard.
Manual-N90-英语.indd 5 2010-8-20 17:01:52

Then following page will be displayed. Aer a couple of seconds this
page will be replaced with the open page as shown below.
Sengs
NOTE: You do not need to enter the SETTINGS menu before you start
to navigate.
To exit this page, touch the arrow in the boom le of the screen.

Calibraon
This funcon calibrates the unit to respond to your screen taps. You
will only need to use this funcon if the unit begins to respond incon-
sistently to your screen taps.
About
The About page is for informaon only. It will give the serial number,
versionEN numbers for the product.
GPS Receiver
NOTE: This page is for informaon only. You can view the number of
satellite signals the unit is receiving and also the strength of these
signals. When the Open page is displayed touch on the GPS Signal
icon. A page similar to that shown below will be displayed.

This page gives your current posion in degrees longitude and
latude, your current speed and the status of your posion, i.e. Fixed
3D or Fixed Invalid etc. The compass s w o h the strength of the signal
from each of these satellites.
NOTE:
At least three GPS signals are required for the device to funcon.
There may be occasions within your home or building when the
signal strength is limited and GPS
Receiver Mode may not be possible. This is quite normal of products
of this type.
Your car may have an athermancy heat reecng windscreen or
windscreen heang that prevents the GPS receiver acquiring a valid
signal.
Navigaon mode
Aer run navigaon this picture appear
Tap to open search address window

To change default language tap on next
next Language
NOTE. Aer select Language must also select Voice.

GOCLEVER’S GENERAL TERMS AND CONDITIONS OF WARRANTY
1. GOCLEVER Sp. z o.o. with registered oce in Poznań (60-431) at
Sianowska Street 4a, hereinaer referred to as Guarantor, guarantees
that GOCLEVER branded product is free from any design or material
defects that could compromise its funconality provided that user
manual supplied at conclusion of the agreement has been adhered
to.
2. This warranty is applicable only on the territory of United Kingdom.
3. Guarantor shall remove any possible defect of the device, in
accordance with the provision of this warranty provided that the
warranty card lled in on the day of the purchase together with a
proof of purchase are presented. Any alteraons or correcons in the
warranty card done by unauthorized persons shall result in the loss of
rights resulng from this warranty
4. The duraon of warranty for GOCLEVER devices shall be 24 months
starng on the date the device was sold, hoverer not to exceed 27
months from the date of producon placed on the Product.
5. The buyer is entled to Return to Base service within 12 months
from date of purchase, however not to exceed 15 months from the
date of producon. Aer those dates the user shall send the defec-
ve device to the repair center, having previously obtained an RMA
Funcon Hardware Specicaon
CPU MStar 500 MHz
Input Method Soware Keyboard
Operang System Microso WinCE.NET.6.0 Core Version
Expansion Slot Micro SD card ( Support up to 8GB)
Antenna Ceramic Antenna ( 25mm x 25 mm ) Internal
Speaker Built-in 2.0W Mono (Internal)
USB USB Client / AcveSync
Memory 128MB DDR2 Ram – 4GB Nandash
Dimension 136mmx 90mmx 13mm
Weight 211g

number in accordance with the RMA procedure. Cost of delivery back
to the customer aer repair shall be covered by the Guarantor.
6. Warranty for LCDs and baeries mounted in GOCLEVER products
is limited to 12 months from the date of purchase, however not to
exceed 15 months from the date of producon TFT LCD screens with
sizes from 3,5” to 10,1” may have up to 5 faulty pixels (white, black
or the so-called sub-pixels).
7. Warranty for accessories added to the device (e.g. holders, cables,
etc.) is limited to 12 month from the date of sale and excludes me-
chanical damage.
8. Defects detected within the warranty period shall be removed free
of charge within the possibly shortest me not exceeding 21working
days from the date on which the devices have been received by the
repair center. Should it become necessary to source spare parts from
abroad, the above me may be extended by further 30 days.
9. Fault must be reported to the repair center not later than within
14 days from its occurrence
10. The buyer is obliged to supply the product in original packaging
complete with all accessories. The Buyer shall be responsible for the
damage resulng from use of dierent packaging.
11. Ownership of the devices that have not be collected from the
repair center within 3 months from compleon of the repair shall
pass on to the repair center.
12. In case of unjused claim (claim relang to fault-free device or
user damage) The Claimant shall be charged with tesng fees and
costs of transport.
13. Warranty does not cover:
Any use of the equipment going beyond the scope of its intended
use;
Claims relang to specicaon of the device if they are consistent
with the ones given by the manufacturer in the user manual or other
normave documents
Defects caused by external forces, e.g. mechanical damage, eects of
weather condions, polluon, water damage, overvoltage, etc.

Defecve funconing of unauthorized soware installed in the
device,
Capacive stylus added to the bundle free of chargé.
14. If a warranty repair requires parts to be changed, the replaced
element remains the property of the Guarantor. Replaced parts may
be of a dierent brand provided that technical parameters are at
least equal.
15. The Buyer loses the warranty right if warranty seals are broken,
the tag with serial number if removed, or should repair centre detect
unauthorised repair or systemic or construcon changes of the
device.
16. Guarantor may waive the deadlines for warranty service should
unexpected circumstances of force majeure arise e.g. natural disa-
ster, social unrest, etc.
17. Guarantor is not responsible for damages and losses incurred as a
result of being unable to use the device while it was serviced.
18. Warranty rights does not include the buyer’s right to claim due to
loss of prots, due to defects of the device.
19. Guarantor shall not be responsible for damage resulng from loss
of data on magnec drives, please note that maps are restored back
to the factory condion.
20. The legal relaons between the buyer and the device and the
Guarantor is governed exclusively by the provisions of this warranty.
Claims for compensaon going further than that are excluded unless
they result from mandatory provisions of law..
21. This warranty has a supplementary character in relaons to buy-
er’s rights towards the seller. Warranty does not exclude, nor limit,
nor suspend buyer’s rights resulng from nonconformity of goods
with the contract.

OWNER’S MANUAL
INSTRUKCJA OBSŁUGI
www.goclever.com

Ważne
Sygnał GPS jest wymagany do poprawnego działania funkcji nawiga-
cja. Sygnał GPS jest ograniczony w budynkach oraz tunelach funkcja
nawigacja nie jest wtedy możliwa. Wynika do z specyki sygnału
GPS i jest normalne w tego typu produktach. Możesz sprawdzić ilość
satelity oraz siłę sygnału w funkcji Sygnał GPS.
Bezpieczeństwo
GPS oparty na satelitach system który umożliwia lokalizację pozycji
na kuli ziemskiej. GPS system jest kontrolowany i nadzorowany przez
rząd Stanów Zjednoczonych, jest on odpowiedzialny za dostępność
sygnału GPS oraz jego dokładność.
Korzystanie w samochodzie
Podczas jazdy samochodem prowadź auto zgodnie z przepisami i
zachowaj ostrożność.
Nigdy nie zmieniaj ustawień nawigacji podczas jazdy. Spoglądaj na
mapę jedynie kiedy jest to bezpieczne. Prowadź samochód z komu-
nikatami jedynie jeśli przepisy na to pozwalają. Podczas montażu
nawigacji upewnij się że to nie grozi twojemu bezpieczeństwu, nie
ogranicza pola widzenia oraz nie utrudnia prowadzenia samochodu.
Bateria
Bateria posiada Litową baterią. Nie należy stosować go w miejscach
wilgotnych, mokrych lub środowiskach korozyjnych. Nie używaj i nie
przechowuj urządzenia w wysokich temperaturach (>60 C) lub bez-
pośrednio na słońcu. Nie przechowuj w mikrofalówka lub pojemnik
ciśnieniowy.
Niezastosowanie się do tych ostrzeżeń grozi utratą gwarancji i mogą
spowodować wyciek jej nagrzanie, wybuch lub zapalenie,
spowodować obrażenia ciała lub uszkodzenie.
Baterię urządzenia należy utylizować w miejscach do tego

przeznaczonych. Nie wrzucaj do kasza ani nie wkładaj do ognia
baterii.
Rozpoczęcie użytkowania
Upewnij się że zapoznałeś się z instrukcją oraz wszystkimi informacja-
mi przed zadziwieniem na infolinia.
Opakowanie
Zawartość opakowania
• Nawigacja GOCLEVER NAVIO 515
• Ładowarka samochodowa
• Uchwyt nawigacji
• kabel USB
• instrukcja
Schemat nawigacji

Ładowanie baterii
Przed użyciem naładuj baterię nawigacji. Pierwsze ładowanie
powinno być do 100% baterii w celu wydłużenia żywotności baterii.
Zalecamy ładować 2 godziny do pełnego naładowania. Kolejne czasy
ładowania mogą być krótsze. Podłącz ładowarkę do portu USB nawi-
gacji następnie ją włącz.
Dioda czerwona oznacza ładowanie baterii. Kiedy bateria zostanie
naładowana w pełni dioda przestanie świecić.
Zalecamy korzystać z nawigacji zawsze z podłączoną ładowarką w celu
utrzymania stałego poziomu naładowania baterii.
Montaż karty microSD w nawigacji (opcja)
Po prawidłowym włożeniu karty powinieneś usłyszeć delikatny
„click” . Jeśli chcesz wyjąc kartę wyłącz nawigację, przyciśnij ją i karta
powinna samodzielnie wyjść z czytnika. Gdy nie można włożyć karty
do czytnika upewnij się że nie jest w zlej pozycji lub czy w czytniku nie
znajduje się już karta microSD.
Nawigacja obsługuje karty do 8GB microSD HC.
Montaż nawigacji w samochodzie
UWAGA!
Nawigacja powinna być zamontowana w sposób nie ograniczający
pola widzenia, nie blokujący działania poduszek powietrznych lub
ograniczając możliwości prowadzenia samochodu i wykonywania
manewrów.
Ładowarka samochodowa
Podczas korzystania z nawigacji zalecamy zawsze podłączenie łado-
warki zgłasza podczas długich tras. Podłącz końcówkę ładowarki do
portu USB nawigacji. Podłącz ładowarkę do gniazda 12V w samocho-
4
Charging the Battery
Before using yourdevice the battery will need to be charged. To maximize the
life of the battery the rst charge must fully charge the battery. We recommend
that you charge the unit for 5 hours in order to achieve the full charge. Subsequent
charge times may be shorter. Plug the mains adapter into the socket on the
rear of the unit USB port.
Plug the adapter into the mains supply and switch it on.
The red charging indicator on the front of the unit will light. When the unit is fully
charged the red indicator is extinguished.
We recommend that when you use navigation in your car, that you always use the
12V cigarette adapter in order to maintain the battery level.
Installing the micro SD Memory Card(Optional)
Once the card is installed it does not need to be removed. If you need to remove
the card, switch the unit off rst, push the card in and it will eject from the slot.
When re-installing it can only be tted one way - contacts towards you and the cut-off
corner at the top as shown. Slide the card in and push fully home so that it clicks in
place.
It can support up to 8GB micro SD card.
Mounting the Unit in your Car
WARNING!
Device must be mounted in a location that does not obscure the drivers vision, impede
use of the car's controls or impede the operation of the car's airbags. Screw the car
mount into the back of the unit as shown below.
Car Adapter
When using your navigation in the car we recommend that you always use
the car adapter to power the unit, especially on long journeys. Plug the car adapter
into the socket marked USB port on the rear of the unit. Plug the other end on
the adapter into the car's 12V accessory socket. The illustration on the next
Manual-N90-英语.indd 4 2010-8-20 17:01:51

dzie. Ilustracja przedstawia typową instalację nawigacji w samocho-
dzie, ułóż kabel zasilania tak aby nie ograniczał manewrów oraz aby
uniknąć możliwości zaplątania się w niego.
Włączanie
Najpierw zostanie wyświetlone logo.
5
Switching On
Firstly The System logo is displayed.
seodt it ah tose l bacr ewopeh txfielbissopf I.noi tal latsnilacipytaswohsegap
not obscure instruments or controls and does not cause a tripping hazard.
Manual-N90-英语.indd 5 2010-8-20 17:01:52

Następnie zostanie wyświetlone menu. Pojawi się ono kilka sekund
po ekranie startowym.
Ustawienia
Ważne: Nie musisz zmieniać Ustawień przed uruchomieniem nawi-
gacji.
Aby wyjść z Ustawień dotknij ikony strzałki w prawym górnym rogu.

Kalibracja
Funkcja ta kalibruje ekran i poprawia odczyt Twoich dotknięć ekranu.
Użyj tej opcji gdy ekran nie będzie prawidłowo reagował na Twoje
dotknięcia.
O Urządzeniu
Storna ta zwiera informacje o urządzeniu jego numer seryjny oraz jaki
to model.
Sygnał GPS
Funkcja ta służy tylko sprawdzeniu poprawności odbioru sygnału GPS.
Jak pokazano poniżej na obrazku

Informacje tu zwarte dotyczą, pozycji czyli współrzędnych na mapie,
dokładności pozycji, czasu, ilości satelity użytych do określenia pozy-
cji, przybliżonej prędkości.
Ważne:
Wymagany jest odbiór sygnału z co najmniej 3 satelity do określenia
pozycji. Gęsta zabudowa lub wewnątrz budynku może uniemożliwiać
odbiór sygnału. Na pogorszenie sygnału może też wpływać jeśli szyba
samochodu jest podgrzewana. W tunelach sygnał GPS nie jest odbie-
rany jest to normalne w tego typu produktach.
Nawigacja
Po uruchomieniu funkcji nawigacja zostanie wyświetlone okno poka-
zane poniżej
Wybierz aby wprowadzić adres celu