Goldstar MV1502B User manual

%website: http://www.lgservice.com
E EN
INSTALLATIONINSTRUCTIONS
PLEASE READ AND SAVE THESE INSTALLATION INSTRUCTIONS_
MV1502W
MV1502B

YOUR SAFETY FIRST
BEFORE YOU START
• Proper installation is the installer's responsibility!
- Read the entire manual before you begin. The Model number label is located on the oven front.
See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2.
BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:
IModel Number Label
Mounting
plate
(Remove from
oven to install.)
Back of oven
Figure 1 Figure 2
WARNING
FOR YOUR SAFETY:
• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled
properly. The dimensions of the oven are as follows:
Height :16 7/16inches
Width : 29 15/16inches
Depth : 15 3/8 inches
Weight : 58 pounds
•Avoid Electrical Shock!
- Before you drill into the wall, note where electrical outlets are and where electrical wires might be behind
concealed the wall, YOU COULD GET AN ELECTRIC SHOCK it you contact electrical wires with your
drill bit.
- Locate and disconnect the power of any electrical circuits that could be affected by installing this oven.
IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.
•ELECTRICAL RATING OF THIS OVEN : 120V AC. 60Hz.
13Amps /1500 Watts (Microwave oven + Cooktop Lamp+ Ventilation Fan)
-You need a 120V, 60Hz, AC only, 15A or 20A, fused electrical supply (located in the cabinet above the
microwave as close as possible to the microwave circuit) serving only the microwave.

YOUR SAFETY FIRST
•THIS APPLIANCE MUST BE GROUNDED!
- If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape
wire for the electric current. This appliance is equipped with a cord having a grounding wire with a
grounding plug.
• Place the plug into a properly installed and grounded outlet. See Figure 3.
• Do not use an extension cord. PROPERLY POLARIZED AND
• Keep the power cord dry and do not pinch or crush it. GROUNDED OUTLET
•DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE
POWER SUPPLY CORD GROUNDING PRONG!
This appliance MUST be grounded? ..t-_::;_L
Three-Pronged (Grounding) plug
Figure 3
WARNING
If you use the grounding plug improperly, you risk electric shock!
- Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do
not completely understand the grounding instructions.
DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.
WARNING
Improper grounding could result in electric shock or other personal injury.
SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.
•DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!
- DO NOT try to operate the microwave oven with the door open.
- DO NOT tamper with or defeat the safety interlocks.
- DO NOT place objects between the microwave oven front face and the door.
- DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.
- DO NOT operate the microwave oven if it is damaged.
- The microwave oven door must close properly to operate safely.
- DO NOT USE THE MICROWAVE OVEN:
• Ifthe door is bent.
• Ifthe hinges or latches are broken or loose.
• Ifthe door seals, sealing surfaces or glass is broken.
- DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF?
It should be adjusted and repaired by a qualified technician who can check for microwave leakage
after repairing the oven.
WARNING
If you do not use the microwave oven as instructed, you could
be exposed to excessive microwave energy.

YOUR SAFETY FIRST
• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.
- Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be
constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
- ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.
- DO NOT mount the microwave oven to an island or peninsula cabinet.
- BE SURE the upper cabinet and rear wall structures are able to support 150 Ibs., plus the weight of any
items you place inside the oven or upper cabinet.
- Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.
- BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.
WARNING
If you do not mount the oven as instructed,
you risk personal injury and/or property damage.
30" rain. cabinet opening
30" rain. clearancefrom bottom
of cabinetto cookingsurface
or countertop
(Use templates included
with installation instructions)
-Grounded Plug
(inside upper cabinet)
Power Supply
CordHole
Figure 4
CAUTION
• Before you begin installing the oven, PLACE APIECE OF THE CARTON OR OTHER HEAVY
MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.
Failure to protect these surfaces could result inproperty damage.

PARTS, TOOLS, MATERIALS
THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:
NOTE: Depending on your ventilation requirements, you may not use all of these parts.
Damper/duct connector
(for roof-venting or wall-venting installation)
Not Actual Size
One power cord clamp and
One dark-colored mounting screw
(to hold the power cord)
Actual Size
Two tapping screws - Actual Size
(for attaching the damper duct connector) One lock pin and one washer-Not Actual size
One power cord clamp bushing - Actual Size
(for the cord hole in a metal upper cabinet)
Four 1/4" x 2" lag screws - Actual Size
(for wall stud holes) Four 1/4" x 3" toggle bolts - Actual Size
(for drywall holes)
Two 1/4" x 2" bolts - Actual Size
(for securing to the upper cabinet)
Two washers - Actual Size
(for the two upper cabinet bolts)
Four spring toggle heads - Actual Size
(for the toggle bolts)
NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall and
the mounting area must meet the 150 Ibs. weight requirement.

PARTS, TOOLS, MATERIALS
YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION:
Carton or other heavy material for covering the counter top.
Clear tape
(for taping the templates to the wall) Stud finder or thin nail.
Saber saw (for cutting vent
hloes for roof or wall venting)
Phillips screwdriver (for the screws)
Pencil I
Flat blade screwdriver (for the bolts)
Key hole saw (for the power cord hole)
3/8" and 3/4" wood drill bits ._
1/2" and 3/16"
drill bits
Plumb line
Measuring tape (metal preferred) Duct Tape
Small side cutters or tin snips Caulking gun
• If you have brick or masonry walls, you need special hardware and tools.
• The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft
damper.

STEP 1: PREPARE THE
ELECTRICAL CONNECTIONS
WARNING
AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!
1. Locate the grounded electric outlet for this oven in the
cabinet above the oven, as shown in Figure 4 Detail.
NOTE: The outlet should be on a circuit dedicated to the
microwave oven 120V, 60Hz., AC only, with a
20ampere fused electrical supply.
IMPORTANT: If you do not have the proper wall outlet, you
MUST have one installed by a qualified
electrician.
2. You will cut the power-supply-cord hole (shown in
Figure 4 Detail) later when you prepare the wall and
upper cabinet in Step 4.
NOTE: Do not use an extension cord.
Keep the power cord dry and do not pinch or
crush it.
Upper
Cabinet
-Grounded Outlet
Ql
Power-Supply-CordHole
Figure 4 Detail
WARNING
Improper grounding could result in
electric shock or other personal injury,
•DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER
SUPPLY CORD GROUNDING PRONG! This appliance MUST be
grounded!

STEP 2:
PREPARE THE VENTING SYSTEM
NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard
ductwork fittings and length are shown in Figure 9, page 9.
WARNING-FIRE HAZARD
THIS OVEN MUST BE PROPERLY VENTED!
You may vent your oven in one of three ways:
Roof-venting If your oven is located on an outside wall near the roof, as in Figures 6 (31/4" x
10" duct) and 8 (6" round duct.)
Wall-venting If your oven is located on an outside wall on the first floor of your house, as in
Figures 5 (3 1/4" x 10" duct) and 8 (6" round duct.)
Room-venting If your oven is located on an inside wall of your house, as in Figure 7.
NOTE: If you choose the rear exhaust method (roof-or wall-venting), be sure there is enough clearance
within the wall for the exhaust duct.
Wall Venting
cabinet
Wall venting
/
3 1/4"x10"
duct
Figure 5
through-the-wall
REMEMBER AS YOU INSTALL THE
VENTING:
• Keep the length of the ductwork and the
number of elbows to a minimum to
ventilate your oven efficiently.
See examples on page 9.
• Keep the size of the ductwork the same.
• Do not install two elbows together.
• Use duct tape to seal all joints in the duct
system.
• Use caulking to seal the exterior wall or
roof opening around the cap.
cabinet
Roof venting
Roof Venting
duct _
through-the-roof
Figure 6
Room Venting
cabinet
ov'
Figure 7
roof cap
6" min.
diameter wall cap
round "_';.'" ";!
elbow
3 1/4"to round
ducttransition
3 1/4" toround
ductworktransition
Figure 8

STEP 2:
PREPARE THE VENTING S YSYTEM
STANDARD FITTINGS
NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3"
extension duct installed between the damper assembly and the adapter to prevent the exhaust
damper sticking.
DUCT LENGTH
The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not
exceed the equivalent of 140 feet.
For best performance, do not use more than three 90 degree elbows.
Below are the standard fittings and their equivalent length in feet.
3 1/4"x10"
to 6"=5ft. 3 1/4"x10" roof
cap=24ft.
3
3 1/4"x10" 90°
elbow=25ft.
90°elbow
=lOft.
5
3 1/4"x10"
wall cap
=40ft.
6
45° elbow
=5ft.
7
3 1/4"x10"
flat elbow
=lOft.
Figure 9
To calculate the equivalent length of each duct piece used, see the examples below.
I
Examples
For 3 1/4"x10" SYSTEMS
3 1/4"x10" _ 6ft. _ [}2_wall cap
90 ° elbow _____2_ft.
1-3 1/4" x 10" 90 ° elbow = 25 ft.
1-Wall Cap = 40 ft.
8 feet straight duct = 8 ft.
TOTAL LENGTH =73 ft.
For 6" ROUND SYSTEMS
90° elbows _----- 6ft. ---_¢ wall cap
transi@
1-transition = 5 ft.
2-90°elbows = 20 ft.
1-Wall Cap = 40 ft.
8feet straight = 8 ft.
TOTAL LENGTH = 73 ft.

STEP 3:
PREPARE THE VENTING BLOWER
Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if
you want wall-venting or room-vented (recirculating) installation.
_k, WARNING _k,
ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.
•DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could
result in electrical shock.
REMOVE THE MOUNTING PLATE:
1. Remove any shipping materials and parts from
inside the microwave oven.
A thick, protective
covenng
2. Cover the counter top or cooktop with a thick,
protective covering to protect it from damage and
dirt. See Figure 10.
NOTE: If you have a free-standing range,
disconnect it, move it onto a piece of
cardboard or hardboard and pull it away
from the wall, so that you can get closer to
the upper cabinet and back wall for easier
measuring and drilling.
3. Remove mounting plate screw(s) (1 or 2 screws)
from the mounting plate as shown and discard.
(See Figure 11.)
4. This plate will be used as the rear mounting plate.
(It will be used to locate and mark the mounting
holes on the rear wall.)
5. Locate exhaust adaptor, grease filters and
hardware packet.
6. At this point, remove any adhesive tape (if there is
any), on the exhaust adaptor, the grease filters
and the power supply cord. Control panel side
Figure 10
Mounting
plate
Mounting plate
screw(s)
(1 or 2 screws)
Figure 11
ROOF-VENTED INSTALLATION:
This oven is shipped assembled for roof-vented.
You will need to install the exhaust adaptor
regardless of cabinet.
1. Attach the exhaust adaptor to the blower plate by
sliding it into the guides. (See Figure 12.)
I
iJ l :
-" _" _ Back
_Figure 12
Exhaust
adaptor
ilOi

STEP 3:
PREPARE THE VENTING BLOWER
WALL-VENTED INSTALLATION:
1. Remove one blower unit mounting screw and one
blower plate screw. Remove the blower plate
from cabinet. See Figure 13.
2. Carefully lift the blower unit out of the microwave
oven.
3. Use side cutters or tin snips to cut and remove
knockouts "B" from Back plate. Discard
knockouts. Be careful not to distort the plate. See
Figure 14.
4. Reassemble the blower wire. See Figure 15.
5. Rotate the unit so that the exhaust ports face the
rear of the cabinet. See Figure 16. When you insert
blower unit, blower wire must be like figure 16.
6. Place blower unit back into cabinet. Check that
the exhaust ports face towards the rear of the
cabinet. See Figure 17.
7. Reattach the blower plate to cabinet so the
exhaust ports and blower plate opening are
aligned. Attach with one blower unit mounting
screw and then one blower plate mounting screw.
See Figure 18.
blower unit -- back plate
_-- blower plate
mounting screws
Parts "B"
blower unit
mounting screw
Figure 13
_Parts 'B' "__ B"
Figure 14
(
Figure 15 Figure 16
exhaust
ports
blower
unit
--11 --

STEP 3:
PREPARE THE VENTING BLOWER
exhaust
ports
Figure 17
blower unit
exhaust ports
_,-- blower plate
mounting screws
blower unit
mounting screws
Figure 18
ROOM-VENTED (RECIRCULATING)
INSTALLATION:
1,
2,
Remove one blower unit mounting screw and
one blower plate screw. Remove the blower
plate from cabinet. See Figure 19.
Carefully lift the blower unit out of the
microwave oveR.
3, Rotate blower unit 90° so the exhaust ports face
the front of the cabinet. See Figure 20.
4. Place blower unit back into microwave oven.
5, Reattach blower plate to microwave oven.
Attach with the one blower unit mounting screw
and then the one blower plate mounting screw.
See Figure 21.
blower plate
mounting screws
blowerunit
mountingscrews
Figure 19
\
-- blower plate
mounting screws
Figure 20
blower
unit blower unit
mounting screws
Figure 21
--12--

STEP 4: PREPARE THE WALL AND
UPPER CABINET FOR INSTALLATION
MEASURE AND TACK /TAPE UP THE
TEMPLATES
1. Using a plumb line and (metal) measuring tape, find
and mark the vertical center line on the back wall, as
in Figure 22.
2. Find and mark one or two points where the studs are
on the wall (Studs are normally 16 inches apart.)
and then measure and mark the stud locations. If
you cannot find any wall stud, consult a local
building contractor.
CAUTION
DO NOT ATTEMPT TO INSTALL THE MICROWAVE
OVEN IF YOU CANNOT FIND A WALL STUD.
3. Line up the plumb line on the wall with the center
line on the mounting plate.
NOTE: Be sure the minimum width is 30 inches and
the distance from the top of the mounting
plate to the range or counter top is at least 30
inches. See Figure 4 on page 4.
4. Center mounting plate in operating by lining up the
plumb line on wall with centerline on mounting plate.
Make sure the minimum width is 30 inches and that
the top of the mounting plate is located a minimum of
30 inches above the cooking surface.
See Figure 23.
NOTE: f the cabinets are not plumb, adjust the
mounting plate to the cabinets. Ifthe front
edge of the cabinet is lower than the back
edge, adjust the mounting plate to be level
with the cabinet front.
O O
Figure 22
©©
5. Measure the bottom of the upper cabinet frame. Trim
the edges "A" "B" and "C" on the upper cabinet
template so that the template will fit on the bottom of
the upper cabinet. If upper cabinet has a recessed
frame, trim template so that it fits inside the
recessed area. Align the centerline of the upper
cabinet template with the centerline of the mounting
plate; then securely tape or tack the upper cabinet
template in place. See Figure 23
Figure 23
--13--

STEP 4: PREPARE THE WALL AND
UPPER CABINET FOR INSTALLATION
DRILL THE HOLES IN THE WALL AND UPPER CABINET.
_, WARNING _k,
BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL.
Electrical wires could be concealed behind the wall covering
and if the drill hits them you could get an electric shock.
1. Find the points on the mounting plate labeled "A", "B", "C", and "D". Drill a 3/16" diameter hole at any
points that are over a wall stud. Drill a 3/4" diameter hole at any points over drywall.
2. Drill a 3/8" hole at points "J", "K", and "N" on the upper cabinet template.
NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x2" filler blocks (not
included) to provide additional support for the bolts. See Figure 24.
• Mark the center of each filler block and drill a 3/8" diameter hole at the marks.
• Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to
cabinet with masking tape. See Figure 25.
3. Cut or drill a 2" diameter hole at the area marked "M".
Power supply cord hole on the upper cabinet template. If the upper cabinet is metal, you will need to cover
the edge of the hole with the power supply cord bushing (supplied) to prevent damage to the cord from the
rough metal edge.
WARNING
YOU MUST COVER THE EDGE OF
THE POWER SUPPLY CORD HOLE
IN A METAL CABINET WITH THE
POWER SUPPLY CORD BUSHING.
FAILURE TO DO SO COULD
RESULT IN DAMAGE TO THE
CORD AND ELECTRIC SHOCK.
4. Cut out the venting areas (with the saber saw):
• Roof-Vented: cut out the shaded area marked "L"
on the upper cabinet template.
• Wall-Vented: go to STEP 5, INSTALL THE
MOUNTING PLATE, located on page 15.
cabinet front filler block cabinet
bottom shelf
Figure 24
filler
5. Complete whichever venting system you have
chosen. Use caulking compound to seal the exterior
wall or roof opening around the wall cap or roof cap.
Figure 25
--14--

STEP 5: INSTALL THE MOUNTING
PLATE TO THE WALL
THE OVEN MUST BE CONNECTED
TO AT LEAST ONE WALL STUD.
1. Draw a vertical line on the wall at the center of the
30" wide space.
Use the mounting plate as the template for the
rear wall. Place the mounting plate on the wall,
making sure that the tabs are against the bottom
of the cabinet. Line up the notch and center line
on the mounting plate to the center line on the
wall.
2. While holding the mounting plate with one hand,
draw circles on the wall at holes A, B, C and D.
Four holes must be used for mounting. If the holes
are not used, the installation will not be secure.
Installer must use these holes for proper
installation. Use toggle bolts through these holes
unless one of them lines up with a stud. Use a
wood screw for studs.
NOTE: Draw a fifth circle inside area E, through
one of the bottom holes to match the location of a
stud.
For wall-vented: The oven requires a rear wall cutout
opening for the rear wall duct and the exhaust
adaptor must be attached to the mounting plate. See
the next page on how to prepare the rear wall cutout
opening and the exhaust adaptor/mounting plate for
wall-vented.
3. Drill holes on the circles. If there is a stud, drill a 3
/16" hole for lag screws. If there is no stud, drill a
3/4" hole for toggle bolts. Make sure to use at
least 1 lag screw in a stud, and 4 toggle bolts in
the drywall or the plaster.
4. Attach the plate to the wall. To use spring toggle
heads bolts: Remove the toggle wings from the
bolts. Insert the bolts into the mounting plate and
replace the spring toggle heads to 3 /4" past the
bolt ends. Insert the spring toggle heads into the
holes in the wall to mount the bracket. You may
pull forward on the bracket to help in tightening
the toggle bolts. Tighten all bolts.
Minimum 66"
Fromthe Foor
L
I
'Mounting
/ Plate
3/16" Hole on Studs
3/4" Hole on Drywall Only
II '
I For Wall-
II Vented Only
.i I , ,
ii- 1.......,
'l-- ,. /,,
iI_tt
/Draw Lines
T
\
°
[_[ Center Line --I_
o oo,oo o oooooooo_
t-----q =
t ' []
Support Tab
on Studs
Draw
Center Line
o
It
\ '
::::: !i!i!i!i!i
' l
Support Tab
Figure 26
Space More Than Wall Thickness
• Toggle Wings _ .
M°Ul_[_:1 _ '1 'l"fT°g gleBoltB_ ] I',:_::
__. II_ _BOltEnd
!N_/'
_Wall /I1: I
Figure 27
i15i

STEP 5: INSTALL THE MOUNTING
PLATE TO THE WALL
TO PREPARE THE REAR WALL
CUTOUT OPENING AND EXHAUST
ADAPTOR/MOUNTING PLATE FOR
WALL-VENTED:
1. Place the mounting plate against the rear wall as
described in step 5 item 1 (page 14).
2. Using a pencil, put dots through slots F and G,
and through holes H and I. Remove the mounting
plate and draw lines extending through the points.
This will give the location and size of the box
cutout for the rear wall duct.
• Attach the exhaust adaptor to the rear mounting
plate by sliding it into the guides at the top center of
the plate on the wall side. Push in securely until it is
past the top locking tabs and in the lower locking
tabs. Take care to assure the damper hinge is
installed so that it is at the top and that the damper
swings freely.
• Carefully guide the exhaust adaptor, now attached
to the mounting plate, into the house duct, before
using the screws to attach the plate to the wall.
This will assure proper alignment for installation.
• Return to step 5, item 3 (page 14) to continue. After
completing the installation of the mounting plate,
again check the rear damper for free movement to
assure it will operate properly.
Exhaust Adaptor
Slide exhaust
adaptor into
guides on
rear panel.
Figure 28
Locking
Tabs
Figure 29
Damper
(hinge side up)
Mounting Plate
(wall side)
Guides
--16--

STEP 6:
ATTACH THE OVEN TO THE WALL
_WARNING _, l_ow _
You will need two people to lift this
microwave. Failure to use more than
one person could result in personal
inj u ry. powercord
1. Carefully lift microwave oven and hang it on
support tabs (See Figure 26) at the bottom of the
mounting plate. Reaching through upper cabinet,
thread power supply cord through the power supply
cord hole in the bottom of the upper cabinet. See
Figure 30.
2. Rotate the microwave oven upward so the top of
oven is against the bottom of the upper cabinet or
cabinet frame.
3. Drop the lock pin and washer assembly into hole
"N" (left side hole) and push the pin down as far as
it will go. See Figure 31.
I
washer ::_
Figure 30
4. Place washers over two 1/4"x3" bolts. Then insert a
bolt down through each hole in the upper cabinet
bottom.
Tighten the bolts until the gap between the upper
cabinet and microwave oven is closed. See Figure
32.
5. Remove lock pin and washer.
If wall-vented or room-vented installation is used,
go to No. 8 on the next page.
Figure 31
Figure 32
i17i

STEP 6:
ATTACH THE 0 VEN TO THE WALL
6. Roof vented installation:See Figure 33
Install ductwork through the vent opening in the
upper cabinet. Complete the venting system
through the roof according to the method needed.
See "PREPARE THE VENTING SYSTEM,"
STEP 2 on the page 8. Use caulking to seal
exterior roof opening around the exhaust cap. See
Figure 6 on page 8.
7. Use power supply cord clamp to bundle the power
supply cord. Install the power supply cord clamp,
using a screw as shown in Figure 34, to inside of
the cabinet.
8. To install the grease filter: Slide it into the slide
slot, then push up and toward oven center to lock.
See Figure 35.
9. Plug in the power supply cord.
Figure 33
power
supply
cord
clamp
Figure 34
10. Read your Owner's Manual, then check the
operation of your microwave oven.
Figure 35
--18--

P/NO. 3828W5U0380 Printed in China