GOLDWOOD Theater Solutions B41GG User manual

B41GG / B42S
B43GR / B61GG
B62S / B63GR
Troubleshooting:
1. If the additional speakers do not connect to the 1st speaker or you do not
hear an audible beep sound when pairing the additional speakers, please
double press the ON/OFF button on the additional speakers again.
2. If your device is an Apple product, make sure only 1 “UUFFOO” record is in
the device list, otherwise, you will not be able to pair. To fix this, simply have
your device “Forget this Device” on any additional “UUFFOO” devices leaving
only 1.

12
Specifications:
- Power: 60W Total System Power
- Sensitivity: 88
- Frequency Resp: 40Hz - 20kHz
- 8 Ohm Impedance
- Woofer: 4”
- Rock Dimensions:
9.45” x 8.86” x 7.87”
- Battery: Lithium
- Charge time - 7 hours
- Charge lasts - 6 hours
- Power: 100W Total System Power
- Sensitivity: 90
- Frequency Resp: 30Hz - 20kHz
- 8 Ohm Impedance
- Woofer: 6.5”
- Rock Dimensions:
12.6” x 11.42” x 9.84”
- Battery: Lithium
- Charge time - 7 hours
- Charge lasts - 6 hours
B41GG, B42S, B43GR
B61GG, B62S, B63GR
Features:
- Weatherproof against rain, snow,
ice, salt, pool chemicals, etc.
- Built In Bluetooth Receiver
- Rust Resistant Grills
- Silicone Sealed, Muiltilayer
Composite Cabinets made
with Hi-Tech Resin
- Butyl Rubber Surrounds
- Voiced for Outdoor Performance
- 2- Way Design and Functionality
Bluetooth Function:
1. Make sure battery is fully charged
before attempting to connect the first
time.
2. Starting with the 1st rock speaker,
press and hold the ON/OFF button
on the bottom of the duck speaker or
Press the Bluetooth Key (4) on the
Remote control. There will be an
audible activation beep and the
indicator light will flash.
3. On your phone, turn Bluetooth to
“ON” and select “UUFFOO” in your
Bluetooth device list. Once device is
connected you will hear a second
audible beep from the speaker and
the indicator light will be blue.
4. PAIRING: To connect with
additional speakers (the 2nd,
3rd…99th speakers), quickly
double press the ON/OFF button on
each additional speaker. You will
hear a beep sound from the addition-
al speaker. Once paired, you should
hear the music playing in a while. To
cancel, the pairing, quickly double
press the ON/OFF button. No beep
will be heard when turning the
speakers off.
5. To turn off the Bluetooth function,
press and hold the ON/OFF button.
Outdoor Installation:
Battery Operation:
Precautions:
When choosing a place for your speakers, try to choose an area on a higher
surface to avoid the speaker sitting in water build up and to maximize drainage
around the speaker. Place it on a flat surface, not tilted, so no water can build up
underneath. In the winter months or during long periods without use, it is a good
idea to bring indoors to maximize speaker life.
Note:Submerging speakers in water (pool or spa) will cease function and void
your speaker’s warranty.
1. Please charge the battery fully before first use.
2. Connect the USB adapter to the speaker using the charge port. While
battery is charging the indicator will be red.
3. Charge the battery until the indicator light is off.
4. After the battery has been charged, turn on the speaker and the indicator
should be blue. Then follow Bluetooth function instructions.
Note:The built-in battery is not replaceable. Please do not remove or replace it
in the trash. If you must dispose of this speaker, bring it to your local recycling
center.
- The USB Cable is not waterproof, please only charge the battery indoors.
- this product should never be submerged in water
- disconnect the power adaptor from the outlet when not in use
- do not stand or jump on this product
- keep this product away from chemicals and high heat
- do not attempt to disassemble the speaker
- do not use this product outdoors if they are cracked or damaged
- do not use these speakers as a floating device