Goodmans GCR1873i User manual

Keep this manual for future reference
User's Manual
IPOD DOCKING SPEAKER
MODEL NO.GCR1873i

CONTENTS
1
Function Description………………………………………1
Declaration…………………………………………………1
About the speaker…………………………………….........2
Keys and ports of the product……...……………………….2
Keys of the remote controller…………...………………….4
Basic functions……………………………………………..5
Power on…..……………………………………………...…5
Play…………………..…………………………………...…5
TUNER….……………………………………………….....5
IPOD………………………………………………………...6
USB………………………………………………………....6
AUX………………………………………………………...6
Pause…….……………………………………..............…..7
Stop …………………………………………..………….....7
Skip-/Skip+ select …….……………………………….…..7
Volume+/-…………………..……………………………...7
REPEAT …………………………………………………...7
EQ………………………………………………………..…7
Mbass…………………………………….………………...7
Sleep setting………………………………………………..7
Clock……… ……..………………………………………..8
Alarm setting……..………………………………………..9
Troubleshooting…………….…………………………......11
Introduction
Thank you for purchasing this new generation multi-functional
speaker!
This product is equipped with multiple functions.
It deserves the name of “Masterpiece” due to its high sound
quality, reliable performance and wonderful industrial design.
May you enjoy great joys and funs from this product.
The speaker integrates powerful functions with exquisite
workmanship.
Main features:
Built-in FM radio
FM (87.5-108MHz)
MW (520-1710KHz)
USB playing
AUX external input
IPOD playing
IPOD video output
Sleep
Clock
Alarm
Sound effects: STUDIO,ARENA,MONITOR,CLUB,FLAT
The unit can provide the backup battery for the time memory,
the unit will not lose the time display when power off, usually
the maximum of memory time is 6 days after powering off.
Precautions:
Firstly, thank you for using this digital composite speaker.
For correct use of it, please carefully read through the operation
manual before use.
Our company reserves the right to make changes on the contents
of this manual, properties and functions of the product without prior
notice.
For better performance of the product, please do not use it under
extreme high or low temperature, humidity, or in the place with
much dust. Particular attention shall be paid to following situations:
1.humid or underwater environment
2.heater or high temperature environment
3.exposed to direct sunlight
4.Environment apt to fall down
5.Do not disassemble the product by yourself to avoid loss of the
right to warranty.

3
2
1 2 3 45 6
123456789
10 11 12
1.AUX: External sound source input
2.USB: USB port
3.VIDEO/OUT: IPOD video output
4.DC 12V: DC output cord
5.FM ANT: FM antenna port
6.IPOD: IPOD jack
1
2
3
4
5
6
7
8
9
10
11
12
Keys, ports and their functions:
POWER: Power On/Off
STOP/BAND: Stop/band select
PLAY/PAUSE/SCAN: Play/pause/scan stations
SKIP-: Previous
SKIP+: Next
FUNCTION: Function shift
MEMORY: Memory key
EQ/MBASS: Sound effect/bass effect select
RAN/ST: Random play/ Shift of tracks
REP/M+: Play mode select/memorized station select
VOL-: Volume decrease
VOL+: Volume increase

45
POWER: Power On/Off
AL1: Alarm setting 1
AL2: Alarm setting 2
MUTE: Soundless
1-0: digit keys
INPUT: Input key
SLEEP: Sleep setting
MEM/SET: Memory/clock setting key
RAN/ST: Random play/shift of tracks
REPEAT: Play mode
MBASS: Mbass key
1
2
3
4
5
6
7
8
9
10
11
Functions of remote controller keys:
12
13
14
15
16
17
18
19
20
21
22
23
REV: Previous/fast backward
FWD: Next/fast forward
M+:Memory +/ select previous item on menu
M-: Memory-/select next item on menu
FUNCTION: Function shift
ENT: Ent
MENU: Menu
VOL+: Volume increase
PLAY/PAUSE/SCAN: Play/pause/scan station
STOP/BAND: Stop/band select
EQ: sound effect setting
VOL-: Volume decrease
Power on: After plugging the DC12V transformer into the port
on the back of the product, the screen lights up and time is
displayed on the screen. Press POWER key to power it on.
Play
1.TUNER: Directly enter FM TUNER state after power on.
(MW operation is same as that of FM.)
Manual radio station searching or direct input: Press SKIP-,
SKIP+ to search radio stations manually, or press INPUT key on
remote controller to input directly the radio frequency (e.g. input
0875 for 87.5 MHz)
Automatic scan: Long press SKIP-, SKIP+ key for more than2
seconds to enter automatic searching radio station mode and it
atomically stops when a radio station is searched out.
Fully automatic scan: Long press PLAY/PAUSE/SCAN key
for more than 2 seconds for fully automatically searching radio
stations It will scan from low to high frequency for local radio
stations with strong signal and save the station automatically.
During scanning, it pre-plays for 3 seconds and shows number
of the station and frequency it saves.
Press STOP/BAND key to shift between FM/AM.
Select a memorized station: Press REP/M+ key on the player
panel to shift to the radio stations it memorizes.
Press M+ or M- to select the desired station.
1234
5
6
7
8
910
11
12
13 14
15
16
17 18
19
20
21
22
23

67
2. IPOD: In the state of FM or AM, short press FUNCTION to
shift to IPOD function. At the time, plug IPOD into IPOD port
to play IPOD music.
Video play: Connect TV video cable to VIDEO OUT jack,
and plug IPOD into IPOD port, open TV OUT on the video file.
While playing video file at this time, corresponding video
pictures will be displayed on TV screen. The product outputs the
sound of the movie normally.
3. USB: In stop state of IPOD, short press FUNCTION to shift to
USB function. Insert USB disk into USB port. At the time,
if it reads content, “no” will be displayed. After successfully
reading, it displays “on”. Press PLAY/PAUSE/BAND to start
playing the music via USB.
4. AUX: In stop state of USB, short press FUNCTION to shift to
AUX function. At the time, insert external sound source
(e.g. MP3, CD) into AUX port on the back of the product to
enjoy the music from AUX. (Make sure that external sound source
is in Play state.)
Pause function: In play state of USB or IPOD, short press
PLAY/PAUSE/BAND for a pause of playing.
Stop function: In play or pause state of USB or IPOD, short press
STOP key to stop playing.
Music select: In play state of USB or IPOD, short press
SKIP-/SKIP+ for previous/next music.
Volume: In state of play or pause, short press VOL+ or VOL- for
volume increasing or decreasing, ranging from 00-30.
REPEAT function: In state of play or pause of IPOD, short press
REPEAT for selection of play mode, such as normal, repeat one,
repeat all.
EQ: In any state of play/pause/stop, short press EQ/MBASS for
mode selection with the sequence of STUDIO,ARENA,MONITOR,
CLUB and FLAT.
Mbass function: In any state of play/pause/stop, long press
EQ/MBASS key to turn on MBASS function. At the time,
“MBASS” is displayed on LCD. Press EQ/MBASS key again to
cancel the function of MBASS.
Sleep setting: In any state of play/pause/stop, short press SLEEP
key on the remote controller to set sleep time for SLEPP00,
SLEEP10, SLEEP20, SLEEP30, SLEEP40, SLEEP50, SLEEP60,
SLEEP70, SLEEP80, SLEEP90.

89
Clock setting: (3 methods)
1. During playing press POWER key to enter STAND By state.
At the time, time is displayed. After pressing MEM/SET key on
the remote controller, “Hour” flashes on LCD. Press Skip- or
Skip+ to adjust “Hour”. After pressing MEM/SET key again,
“Hour” on LCD stops flashing to display the digit confirmed.
And then “Minute” flashes. Press P Skip- or Skip+ to adjust
“Minute”. Press MEM/SET key again to confirm setting and
returns back to time display state.
2. During playing,after pressing MEM/SET key on the remote
controller, “Hour” on LCD flashes. Press INPUT on remote
controller, LCD will display “ : ”, and then directly press digit
keys on the remote controller to input the time desired.
For example, input 0830 for 8:30. This product adopts 12-hour
system. Please input 20:30 for 8:30 pm. After completing
inputting, return back to time display state.
Alarm function:
·Alarm time setting: (2 methods)
1.Press POWER key to enter STAND By state. After long pressing
AL1 on the remote controller, “Hour” on LCD flashes. Press
Skip- or Skip+ to adjust “Hour”. After pressing AL1 again,
“Hour” on LCD stops flashing to display the digit confirmed.
And then “Minute” flashes. Press Skip- or Skip+ to adjust
“Minute”. Press AL1 key again to confirm setting and returns
back to time display state. During alarm time setting, alarm
icon flashes.
2.Press POWER key to enter STAND By state. After long pressing
AL1 on the remote controller, “Hour” on LCD flashes.
Press INPUT on remote controller, LCD will display “ : ”,
and then directly press digit keys on the remote controller to input
the alarm time desired. For example, input 0830 for 8:30.
This product adopts 12-hour system. Please input 20:30 for
8:30 pm. After completing inputting, return back to time display
state. (AL2 setting is same as that of Al1)
In any mode, the Alarm Volume can not be set up and changed.
3. During playing press POWER key to enter STAND By state,
time is displayed. After pressing MEMORY key on the remote
controller, “Hour” on LCD flashes. Press Skip- or Skip+ to
adjust “Hour”. After pressing MEM/SET key again, “Hour” on
LCD stops flashing to display the digit confirmed. And then
“Minute” flashes. Press Skip- or Skip+ to adjust “Minute”.
Press MEM/SET key again to confirm setting and returns back to
time display state.

·Alarming mode setting: In STAND BY state, short press AL1 to
select an alarming mode, the available modes in sequence are
alarming state, IPOD state, TUNER state and cancel alarming.
(After alarming time is set, it will alarm only when an alarming
status has been selected)
· Enable snooze function: When it keeps alarming, press any key
(except POWER, VOL+ and VOL- keys) to turn on snooze
function. “SNOOZE” will be displayed on LCD.
·Cancel snooze function: When SNOOZE is being displayed on
LCD, short press POWER key to cancel snooze function.
At the time, SNOOZE disappears from the LCD.
Troubleshooting
1.No power supply
Solution: Please make sure the power socket is in good condition.
2.No music played out
Solution: Make sure it is in play state and volume is not at 00 level.
Attachment:
1.Users' Manualx1
2.FM Antennax1
3.VDE type adaptorx1
4.Remote controllerx1
5.IPOD Transformable switch x6
10 1 1