Gorilla Playsets See Saw User manual

ASSEMBLY MANUAL
Copyright © 2015 Gorilla Playsets
All Rights Reserved
Latest Revision: July 2, 2015
Gorilla Playsets • 190 Etowah Industrial Court Canton, GA 30114
www.gorillaplaysets.com
See Saw
™
™
playsets
playsets

TABLE OF CONTENTS
Page 2
Warranty, Safety Guidelines and General Information.............…….......……...Pages 3 - 7
Kit Contents and Tool List…………..………………………………………....... Pages 8 - 10
Steps 1-6 .................................................................................................... Pages 11 - 16
Customer Registration Card……………………….....…..…………..….…………... Page 17
PLEASE READ OWNER’S MANUAL CAREFULLY
BEFORE STARTING ASSEMBLY!
®

Page 3
®
IMPORTANT – PLEASE READ
As fresh lumber acclimates to its new environment, the natural tendencies of the tree
can show itself in the form of checks, or “cracks” in the lumber. In almost all cases this is
normal and it will not affect the structural integrity of your See Saw.
Cosmetic defects that do not affect the structural integrity of the product, or natural
defects of wood such as warping, checking or any other physical properties of wood that
do not present a safety hazard, are not covered by this warranty. Defects that develop
because the product is exposed to extreme climate conditions are not covered by this
warranty. Defects that develop as a result of faulty or improper installation of the product
are also not covered by this warranty.
Most cracks are not warrantable, however if you believe that the integrity of your
play set is compromised by this natural occurrence, please follow the warranty claim
procedure found at www.gorillaplaysets.com. Click on the “Customer Care” tab on the
left hand side of the page, then click on “Warranty Claim” and follow the instructions.
We appreciate your purchase and know that you will enjoy your See Saw for many
years to come.
IF YOU HAVE MISSING OR DAMAGED PARTS OR NEED ASSISTANCE
ASSEMBLING, PLEASE CALL Gorilla PlaysetsTM MANUFACTURING DIRECT.
[phone] FACTORY HOURS – MON.–FRI., 8AM-5PM EST DO NOT RETURN
THIS PRODUCT TO THE RETAILER OR CONTACT THE RETAILER DIRECT.
THE RETAILER DOES NOT STOCK COMPONENTS. PLEASE RETAIN THESE
INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE
WHERE YOU CAN REFER TO THEM AS NEEDED.
CONTACT INFO:
Gorilla Playsets
190 Etowah Industrial Court
Canton, GA 30114
Tel. [phone]
Fax. [phone]
[email protected]
Check for revised instructions at www.gorillaplaysets.com/category-s/92.htm

Page 4
®
Thank you for choosing Gorilla Playsets®
We’ve included everything you need, except tools, to build your very own professional
looking See Saw. When complete, your new See Saw should far exceed the quality of
See Saw kits from other build-your-own companies. Our engineers and design team
have over 30 years of playground experience. What we’ve developed is a product that
doesn’t compromise quality for simplicity. Yet you’ll appreciate how quick and easy
construction really is! Our See Saw kits are designed for children ages 3 to 11. Gorilla
Playsets® believes every child should have a See Saw and with our kits they can! You
can rest assured your new See Saw is safe, durable and designed to hold up to the
elements. As parents ourselves, we know how important the security and well-being of
our children is, and this shows in all of our products.
Each See Saw features our step-by-step 3D illustrated manual, powder coated
components, plus all the required hardware and pre-milled lumber.
Quality Lumber
At Gorilla Playsets, we use only the nest, hand selected lumber available. You can be
assured that our lumber is strong, durable, and conforms to the national standards for
use in children’s play equipment. It’s this quality that allows us to offer a 1 year warranty
on the lumber used in our See Saw.

Page 5
®
Limited Manufacturers Warranty
Gorilla Playsets® (“Gorilla”) warrants its See Saw to be free from defects in
workmanship and materials, under normal use and conditions at its original installation,
for one year for structural wood components and for one year for all other components
(e.g., hardware, plastics, tarps, rope ladder, etc.)
Cosmetic defects or natural defects of wood (e.g., warping, seasonal checking or
cracking, knots, or knot holes, etc.) that do not affect the structural integrity of the
product are not covered by this warranty. Defects that develop because the product is
exposed to extreme climate conditions, or that develop as a result of faulty or improper
installation of the product, are not covered by this warranty. Fading or discoloration of
any part or accessory, cracks in plastic components, surface rust on hardware, and
chips on powder coated materials are not considered defects in material as long as they
do not affect the functionality or structural integrity of the part or component.
It is the owner’s responsibility to properly maintain the product. Instructions for proper
maintenance can be found on Gorilla’s website. Imperfections or defects that develop
because of a failure to properly maintain the product are not covered by this warranty.
Gorilla will repair or, at its discretion, replace any part within the stated warranty period
that is defective in workmanship or materials. This decision is subject to verication
of the defect, which, at Gorilla’s discretion, may be accomplished by submitting
photographs or by delivery of the defective part to Gorilla. Any warranty claim must
include proof of purchase, including the date of purchase.
This warranty is valid only if the product is used for the purpose for which it was
designed and installed at a residential, single-family dwelling. This warranty is void if
the product is put to commercial or institutional use. This warranty does not cover (a)
products that have been damaged by acts of God, negligence, misuse, or accident, or
that have been modied or repaired by unauthorized persons; (b) the cost of labor; or
(c) the cost of shipping the product, any part, or any replacement product or part.
GORILLA DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF
ANY KIND, EXPRESSED, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. GORILLA WILL NOT BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. This warranty is valid only in the United States
of America, is nontransferable and does not extend to the owners of the product
subsequent to the original purchaser, and only applies to the product as originally
installed (in other words, installing the product and then later disassembling and
reinstalling the product at the same or another location voids the warranty). Some states
do not allow limitations on implied warranties or exclusion of incidental or consequential
damages, so these restrictions may not be applicable to you. This warranty gives you
specic legal rights. You may also have other rights which vary from state to state.

Page 6
®
IMPORTANT SAFETY GUIDELINES
This product is intended for residential use only and not intended for use in any public
setting. A safety surface such as mulch or recycled tires should be used under the See
Saw to prevent injury from falls. Also a 6 foot safety zone should be used around the
entire See Saw.
As with any home project, good judgment and respect for power tools will greatly
reduce the risk of injury. Gorilla recommends you follow all tool manufacturers’ safety
guidelines. Always wear eye protection and safety gloves to prevent injury. In several
phases of construction two people may be required for lifting and securing of lumber.
While the See Saw is being constructed, please keep children off the See Saw until the
project is complete. Bolts and screw heads should be checked regularly for tightness.
Gorilla shall not be liable for incidental, indirect or consequential damages or injuries
that result from the building and/or playing on our See Saw. Adult supervision is
recommended anytime the See Saw is being used.
Weight Limit See Saw: 300 lbs Total

Page 7
®
General Info to Review Before Installation
• Depending on your experience, assembly of the See Saw can take as little as 1 hour
up to 2 hours.
• Identify all of the parts for your See Saw. Empty the box and lay out boards so you can
see each part. Your instruction book will have detailed drawings that will make it easy
for you to recognize individual parts. Keep all hardware and metal parts separate from
wooden pieces.
• After everything is laid out, check carefully to ensure all parts are present. Make sure
there are no broken boards.
• Find an area to sort your hardware. It is best to open the hardware on a solid surface
so that you do not lose any pieces in the grass. This will save time and familiarize you
with all the different pieces in the hardware bag.
• Important note: Wood has some natural defects such as knots, surface cracks, etc…
We reject parts that are structurally defective. We use a high quality lumber in our
structures; however, you should inspect each part for splinters or rough spots and sand
them smooth to prevent injury.
• After familiarizing yourself with all of the components, read all instructions thoroughly.
Reading instructions after you have studied the parts will help you understand more
clearly the installation process, and help to eliminate unnecessary mistakes.
• Pay close attention to the diameter and length of each bolt and screw.
• Never tighten hardware completely at rst. It helps to have some adjustment for bolt
alignment while you are attaching parts together. After everything is square, tighten
each joint.
• After you complete installation, make sure every bolt, screw, and nut is tight, and every
board is secure. Wood will expand and contract with the seasons.
• Check all bolt connections every season.
• Place the See Saw on level ground, not less than 6ft from any structure or obstruction
such as a fence, garage, house, overhanging branches, laundry lines, or electrical
wires.
READ! VERY IMPORTANT!
If you are missing parts or have questions regarding the installation of our quality
product PLEASE call us directly at the factory (1-800-882-0272). Our trained staff will be
happy to assist you.
Customer service hours:
Monday thru Friday 8AM – 5PM EST
E-mail: [email protected]

Page 8
®
REQUIRED TOOL LIST:
___ Standard or Cordless Drill w/ Phillips Bit
___ 1/8” Drill Bit
___ 9/16” Wrench and Socket
___ 9/16” Deep Well Socket
___ Tape Measure
___ Extension Cord (if using standard drill)
___ Hammer
___ Pencil
Hardware:
see following pages
Wood Components:
see following pages
Counter-sunk Holes - Many of the parts that will be used have counter-sunk holes. A
counter-sunk hole is one that surrounds one side of a thru hole, but does not extend
through the wood itself. When using a counter-sunk hole the bolt will be inserted
through the thru hole. In some cases the bolt head with a washer will occupy the
counter-sunk hole. In other cases a nut with a washer will occupy the counter-sunk
hole.
Lag Screws - Lag screws are used in the construction of the See Saw. There will
not be predrilled holes in the parts for the lag screw installation. Lag screws are self-
tapping, though if you are using a manual socket wrench it may be necessary to tap the
head of the lag screw with a hammer. You should also be sure to tighten the lag screws
completely. Power tools such as an impact wrench or power drill should have enough
torque to drive the lag screws without using a hammer, but make sure not to over
tighten as this can cause the threads to “strip out” in the part.
READ! VERY IMPORTANT!
If you are missing parts or have questions regarding the installation of our quality
product PLEASE call us directly at the factory (1-800-882-0272).Our trained staff will
be happy to assist you.
Customer service hours:
Monday thru Friday 8AM – 5PM EST
E-mail: custsr[email protected]
Counter-sunk Hole
Thru Hole

Picture Description Qty.
3/8 x 3-1/2”
Lag Screw
16
3/8 x 5”
Lag Screw
12
3/8 x 10”
Carriage Bolt
1
3/8” Washer
Torque Washer
29
1
3/8” Lock Nut
3/8” Green
Bolt Cap
1
1
#10 x 2”
Self Tapping
Screw
4
1-3/8” X 6”L
Pivot Pipe
1
1-3/8” x 11-1/2”
Handle Pipe
2
1-3/8”
Vinyl Cap
4
Page 9
®

Picture Description Qty.
4 X 6 X 96”
Main Beam
1
4 X 4 X 18-1/2”
Frame Block (At Right)
(One countersunk hole)
4 X 4 X 18-1/2”
Frame Block (At Left)
(Two countersunk
holes)
1
1
4 X 4 X 13-3/4”
Seat
4
4 X 4 X 20-1/2”
Leg
4
2 X 6 X 23-1/2”
Side Leg Support
2
2 X 4 X 17-1/2”
Lower Leg
Support
2
4 X 4 X 9-1/2”
Handle Block
2
Page 10
®