Graco RoadView 24G633 User manual

Instructions
RoadView™Camera for RoadLazer™
Line Striping System
Video Guidance System (a RoadLazer System Option)
Model 24G633, Series A
With color CCTV camera, LCD color monitor, cables, and mounting hardware
Important Safety Instructions
Read all warnings and instructions in this manual and in related manuals.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
3A1216C
EN

Video Guidance System
23A1216C
Video Guidance System
Installation
This manual makes references to other components in
the RoadLazer System. For complete warnings and
safety instructions see RoadLazer™Line Striper System
manual. Save these instructions.
Video Monitor Installation
1. Mount video monitor in truck cab in a position that is
easy to view. Mount it level with dashboard but not
obstructing forward vision. Monitor has mounting is
supplied with windshield mounting bracket.
2. Connect plug of camera power/video cable to cam-
era.
3. Connect monitor cable plug to monitor power cable.
4. Connect end of monitor power cable to truck recep-
tacle.
Camera Installation on Gun Arm
1. Install mounting bracket onto gun arm.
2. Mount camera to bracket with fasteners and tighten
with fingers. NOTE: Camera can be mounted in
either A or B locations.
3. Route camera cable through hose wrap and camera
location. Plug camera into power/video cable. Turn
monitor ON. Press A/V button once if image is not
seen on monitor.
NOTICE
To Prevent damage to the video monitor:
• Do not expose video monitor to extreme
temperatures or direct sunlight.
• Avoid dust and moisture.
• Avoid dropping and strong impact.
• Turn power off and unplug the adaptor when not
in use or during thunderstorm.
• Do not attempt to perform maintenance.
ti16411a

Video Guidance System
3A1216C 3
4. Aim camera in direction of travel then tighten to 12
in-lb. Review image on monitor to ensure camera is
in correct orientation.
Camera Installation on Flatbed
1. Install mounting bracket onto extension arm.
2. Mount extension arm to flatbed, or other desired
location on truck.
3. Mount camera to bracket with fasteners and tighten
with fingers.
NOTE: Camera can be mounted in either A or B loca-
tions.

Video Guidance System
43A1216C
4. Route camera cable accordingly.
5. Aim camera in direction of travel then tighten to 12
in-lb. Review image on monitor to ensure camera is
in correct orientation.
Install Cross hairs (Optional)
Elastic cross hairs allow the user to create a reference
line to guide the vehicle while striping. A vertical line
may be used to define the reference point.
1. Install TABS onto monitor after it has been placed in
the vehicle. For best results wipe monitor sides with
alcohol to remove any contaminants from the sur-
face. Remove tape film and apply tab to monitor in
the desired location (2 places).
2. Mount magnet line to monitor. For best reference
the line should be as close as possible tot he moni-
tor.
3. Adjust vertical line to your preference by sliding the
magnet on the monitor (if cross hairs are desired).
NOTE: Remove monitor when not in use to prevent it
from obstructing view while driving.
NOTE: When not in use, disconnect power to monitor to
prevent power from being drained from vehicle battery.
ti16415a
(Preferred Orientation)
ti16414a
ti16413a

Video Guidance System
3A1216C 5
Installing the Auxiliary Camera (Optional)
1. Select view location for camera. The gun arm
bracket is made to accommodate 2 cameras. To
mount second camera see Camera Installation
steps 3-5 (page 4). Press A/V button to switch
between cameras on monitor.
2. The magnetic base can be used to mount camera in
any location with ferrous material. Route cable
accordingly.
a
(Alternative Mounting)
ti16411a

Operation
63A1216C
Operation
For RoadLazer operating instructions, see RoadLazer
System manual 3A5384. Striping
To get accustomed to using a reference string to paint
lines, practice spraying with water. The cross hairs can
be moved across the screen in infinite increments to
provide a guideline to place accurate lines. For exam-
ple, when painting a single line the elastic string can be
place centered on the paint gun. When driving, keep the
line to be painted on the elastic string for accurate over-
lay. Alternately, the elastic string can be placed in the
center of the gun arm as shown above. In this case the
driver would keep a constant from one line or centered
between two lines. Using the elastic string is a matter of
user preference. This can be mastered after minutes of
use to paint accurate lines on roadway surfaces. A sec-
ond camera can be mounted onto the gun arm for a
wider angle view. This can be useful for painting curved
lines. To switch between two cameras press the AV but-
ton.
6 mm
16 mm

Troubleshooting
3A1216C 7
Troubleshooting
Problem Cause Solution
No picture on video monitor screen No power to camera or monitor
No video signal
Check connections.
Check truck fuse.
Check video connections. Repair or
replace cable.
Check cable connection between
monitor video cable (122) and cam-
era power cable (61).
Faint or hard-to-see image on video
monitor screen
Glare on video monitor screen Tilt monitor back slightly.
Rotate monitor slightly left or right.
Wear dark clothing.
Tint truck windows.
Washed out colors on video monitor
screen
Contrast or color settings out of
adjustment
Adjust with controls on monitor.

Parts - Video Camera and Gun Arm Mounting Assembly
83A1216C
Parts - Video Camera and Gun Arm Mounting Assembly
Ref. Part Description Qty.
1 16G158 MONITOR, LCD, color 1
24H612 KIT, monitor (includes 5) 1
2 24G838 SLIDE, cross hair with tape 2
3 110755 WASHER, plain 2
4 24G837 ADJUSTER, cross hair 1
5 16G443 BRACKET, windshield mount 1
6 16G160 CABLE, camera 1
9 16G444 BRACKET, mounting, double
camera
1
12 100016 WASHER, lock 2
13 101501 SCREW, mach, slot hex wash 2
16 24G771 CAMERA, 6 mm (includes 6) 1
24H555 CAMERA, 16 mm (includes 6) 1
17 16G442 SPOOL, elastic string
(not shown)
1
18 16G448 CABLE,automotive, power supply 1

Parts - Extension Mounting Arm
3A1216C 9
Parts - Extension Mounting Arm
Ref. Part Description Qty.
25 191692 BRACKET, support 1
26 24F989 EXTENSION, arm, guide 1
27 224136 CLAMP, extension 2
28 111145 KNOB, pronged 2
29 191691 BRACKET, mount 2
30 191694 BAR, lock 2
31 105431 SCREW, manifold 4
32 101566 NUT, lock 4
33 100017 SCREW, cap, hex hd 2
34 109570 WASHER, plain 2
35 801020 NUT, lock, hex 3
36 131390 BOLT, 1/2-13 fully threaded 1
37 112731 NUT, hex, flanged 1

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A1216
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2017, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision C, February 2018
Technical Data
Video Guidance System
Electrical requirements
Sender input 12-15 VDC
Ground Negative
Operating Temperature 32 - 130 F (0 - 54 C)
Weight (approximate)
Camera and bracket (with magnet) 0.75 lb (0.34 kg)
Monitor 1.25 lb (0.57 kg)
Dimensions (approximate)
Camera Body 2.54 L x 2.32 Dia.
Monitor 9.06 in. L x 6.0 in. W x 1.40 in. D