Granit 5070010848 User manual

Operating Instructions
Multi-Monitor-System
5070010848
These operating instructions must be read thoroughly before use and followed. These
Operating Instructions must be retained for future reference.
Translation of the original operating instructions

Operating Instructions for Multi-Monitor-System
5070010848
2
Table of contents
1 About these instructions and symbol descriptions .................................................... 3
2 Safety and accident prevention rules ..................................................................... 3
2.1 General safety instructions ............................................................................. 3
2.2 Device-specific warning and safety .................................................................. 3
3 Performance specifications ................................................................................... 4
3.1 Intended use ................................................................................................ 4
3.2 Technical parameters..................................................................................... 5
4 Operating the video system .................................................................................. 5
4.1 Establishing a connection between the monitor and the camera .......................... 5
4.2 Monitor Menu Operation ................................................................................. 6
5 Maintenance and care .......................................................................................... 7
6 Storage and transport .......................................................................................... 7
7 Disposal ............................................................................................................. 7
8 EC declaration of conformity ................................................................................. 8
9 Warranty............................................................................................................ 9
10 Addresses ....................................................................................................... 9
11 Legal Notice..................................................................................................... 9

Operating Instructions for Multi-Monitor-System
5070010848
3
1About these instructions and symbol descriptions
The information in these operating instructions is labelled as follows:
DANGER
Warning of personal injury or environmental
damage.
IMPORTANT
Warning of property damage.
NOTE
Additional information.
2Safety and accident prevention rules
2.1 General safety instructions
The manual has been created so that you can work safely with the device.
Read the manual thoroughly before operating. Pay particular attention to the safety
instructions.
This manual is intended for people with basic technical knowledge of handling devices
such as the one described here.
If you have no experience with such a device, you should first have an experienced person
help you.
Keep all documents supplied with the device, so you can check if necessary. Keep the
purchase receipts for any warranty claims.
If you should lend or sell the device, all the required documents should be given to the
person using the device.
Observe the operating and maintenance instructions, which can be found in this manual.
For defective devices maintenance orders should be put into place to keep the extent of
the damage minimal and not to compromise the safety of the appliance.
The system components must be installed and operated only under the conditions laid
down in these operating instructions and conditions.
Retrofits, changes or modifications to the device are strictly prohibited. They require
definitely the consultation and written approval of the manufacturer.
If during operation (residual) show hazards and risks which are not described in this
manual, the operator is obliged to report this to the manufacturer.
2.2 Device-specific warning and safety
DANGER: Failure to observe the following safety instructions can lead to serious
accidents causing high injury and damage!
Always pay attention to the direction and the traffic situation and the vehicle’s
environment. The system cannot substitute for the driver/operator’s attention.

Operating Instructions for Multi-Monitor-System
5070010848
4
Use the support system only if it provides a good and clear picture. The picture may be
disturbed by dirt, vibration or a defect.
The responsibility when entering/leaving a parking space, manoeuvring or similar
manoeuvres and pivoting movements of attachments rests with the driver.
Please note that certain surfaces and materials (for example, wire mesh fences, trailer
noses, surfaces of water bodies, etc.) cannot be recognized by the system or display
properly.
The cameras have blind spots where objects, animals and people are not recognized.
Pay particular attention to small children and persons directly located next to the machine,
residing in blind spots.
Keep the environment always in view even using the conventional mirror.
Low or particularly high-lying obstacles can be eliminated depending on the camera
settings from the perspective of the camera.
The camera lens scales and distorts the view, so that objects, people and distances appear
differently to you.
NOTE: By following the operating instructions personal injury, accidents and damage
can be avoided.
In order to become familiar with the system and its display, we recommend the practice
of working and driving manoeuvres on a pedestrianized area outside the public traffic area
with good visibility and weather conditions.
In order for the display to always show the best picture, the camera must be mounted
clean and free of vibration.
3Performance specifications
3.1 Intended use
The rear view camera system is an additional support system for the driver/operator to
improve the view of the vehicle, the engine and its environment.
Basically it has an exclusively supportive role, the responsibility for damage and injuries are
the responsibility of the driver.
It does not replace the duty of care and attention of the driver and must be used in
combination with conventional devices such as mirrors and the direct view of the
infrastructure and the environment.
Failure to comply with the provisions of the generally accepted rules and the provisions of this
manual, including insufficient maintenance, the manufacturer cannot be held responsible for
any damage.

Operating Instructions for Multi-Monitor-System
5070010848
5
3.2 Technical parameters
Display device
Color TFT-LCD
Size
7" Digital Screen
Operation frequency
2400~2483.5MHz
Receiving sensitivity
≤-86dBm(1MHZ QPSK MD300RE)
Resolution
800×(RGB)×480
View angle (LR/UD)
L/R: 70/70 U/D: 50/70
Contrast ratio
500:1
Luminance (cd/m2)
450
Response time (ms)
25
Load dump
DC 12+87V/400ms
Operating temperature
-20℃～+70℃
Storage temperature
-30℃～+80℃
operating voltage range upply
DC8V～32V （5W Max）
Dimension(L x W x T)
(218X149X82mm)
Transmission power
18dBm with Power control
Camera
Color CMOS Camera
Image pick-up device
1/3" Color CMOS
Picture elements
NTSC:720(H)X480(V);PAL:720(H)X480(V)
Horizontal resolution
500 TV Lines
Minimum illumination
0 Lux At Night ( IR LED ON)
View angle
120°
Waterproof rating
IP69K
Shockproof rating
10G
operating voltage range
DC11~32V
Dimension
106(W) x 75(H) x 70.4(D) mm
4Operating the video system
4.1 Establishing a connection between the monitor and the camera
After opening the packaging check that all components are complete and undamaged. If
components are missing or defective, contact your dealer immediately and do not use the
device until its use has been approved by your dealer.
Before first use, the monitor must be connected to at least one camera.
1) Loosen the screw on the back of the camera using a Phillips screwdriver (size PH1). Use
a needle or other pointed object to press the connection button under the screw.
2) Turn on the monitor and camera, go to the Monitor menu and select the device connection
icon. Press the Enter button. The display shows “PAIRING START 30” and a countdown
starts.
3) Press the connection button on the back of the camera. Wait a few seconds until the
display switches to the camera display.
4) Repeat steps 1-3 to connect additional monitors.
Connection button

Operating Instructions for Multi-Monitor-System
5070010848
6
Before connecting to the vehicle’s electrical system, the battery must be disconnected from
the vehicle. The power supply connection point must be coordinated with the vehicle
manufacturer or the vehicle operating manual. Connection work may only be carried out by
trained specialists.
4.2 Initial start up
Symbols on the display:
DANGER: Note that the camera is only a support and the driver is never to be ruled
out of its duty of care. Carelessness can result in serious accidents with high
property losses and to fatal injury.
DANGER: The operation must be only carried out when the vehicle is stationary.
Distractions can cause serious accidents.
1) Image settings:
1. Brightness setting 0-9 steps (left / right key adjustment)
2. Contrast setting: 0-9 steps (left / right key adjustment)
3. Color setting: 0-9 steps (left / right key adjustment)
This feature can only be controlled by the RX1 display.
2) Mirror settings:
Set the four states of the camera image:
Original, horizontally mirrored, vertically mirrored, horizontally and
vertically mirrored. Use the “Left/Right” arrow buttons to select the
desired image for the respective camera.
3) Function setting:
1. NC
2. Turning the ambient light mode of the LED screen on and off;
3. Reversing Ruler Setting: Set the RX1/ RX2/ RX3/ RX4 channel
reversing scale to open and close.
4) SD card storage settings:
1. NC
2. NC
Image settings
Automatic
conversion
settings
Function settings
Save time
settings
Play
settings
Pairing

Operating Instructions for Multi-Monitor-System
5070010848
7
5) Code setting:
To establish the connection between screen and camera, both devices
must be switched on. Select “PAIR” via the menu selection and confirm
with “OK” . The instruction “PAIRING START 30” will appear; switch the
camera off and on again within 30 seconds. After 5-10 seconds the
camera image will appear on the display
5Maintenance and care
Carrying out maintenance and repair work must be conducted only by qualified personnel.
Ensure that the spare and wear parts are original.
Carrying out maintenance and cleaning work and the correction of malfunctions are
generally permitted only when the vehicle is outside the public traffic area.
Fasteners must be regularly checked for tightness and, if necessary, pulled and adjusted.
Clean the optics of the camera with a damp and soft cleaning cloth without any kind of
cleaning agents.
Important: The use of abrasive cleaners or high pressure cleaners and water jet can
damage the optics of the camera, as well as the surface of the screen.
DANGER: Failure to comply with maintenance information can lead to serious
accidents and use impairments.
6Storage and transport
Check the condition of the device before storage and perform the maintenance work before
stopping so that you may video system is ready quickly.
7Disposal
The separate, environmentally friendly disposal of materials encourages recycling of
materials. Therefore, after expiry of the normal service life, the equipment itself and all related
components, including the packaging, should be disposed of at a recyclables collection point.
Packaging, equipment and accessories are made of recyclable materials and should be
disposed of accordingly. If the unit is no longer serviceable, make sure it is unusable before
disposal.
DANGER: If you do not have the necessary expertise, consult an expert with the
dismantling and disposal. RISK OF INJURY!
!!! Always observe local disposal regulations !!!

Operating Instructions for Multi-Monitor-System
5070010848
8
8EC declaration of conformity
The manufacturer,
Wilhelm Fricke SE
Zum Kreuzkamp 7
DE-27404 Heeslingen
hereby declares on its sole responsibility that the multi-monitor-system
Type/series identification:
5070010848
is in conformity with the provisions of
2014/53/EU Radio Equipment directive
2011/65/EU Restriction of the Use of Certain Hazardous Substances in
Electronic and Electrical Equipment (RoHS)
The product was developed in accordance with the following standards:
Safety EN 62368-1:2014+A11:2017
Health EN 62479:2010
Electromagnetic compatibility ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-3 V2.1.1 (2019-03)
Radio ETSI EN 300 328 V2.2.2 (2019-07)
IEC 62321-3-1:2013
IEC 62321-5:2013
IEC 62321-4:2013+AMD1:2017
IEC 62321-7-1:2015
IEC 62321-7-2:2017
IEC 62321-6 :2015
IEC 62321-8 :2017
Technical documentation is kept by:
Mr. Eike Viebrock
Wilhelm Fricke SE
Zum Kreuzkamp 7
DE-27404 Heeslingen
The serial number and model year are shown on the type plate of the equipment.
Heeslingen, 03.12.2020
Translation of the original declaration of conformity
________________________________________
Holger Wachholtz, Board

Operating Instructions for Multi-Monitor-System
5070010848
9
9Warranty
The warranty terms of Wilhelm Fricke SE, as can be found in the sales documents and the
current version of the Terms and Conditions, apply.
In case of questions, please contact the company's customer service line.
10 Addresses
Sales/Customer Service/ Tel.: [phone]
Spare parts sales: Fax: [phone]
Postal and shipping address: Wilhelm Fricke SE
Zum Kreuzkamp 7
DE-27404 Heeslingen
11 Legal Notice
Translation of the original operating instructions for the multi-monitor-system
Manufacturer: Wilhelm Fricke SE - DE-27404 Heeslingen
1. edition March 2020
©2020 Wilhelm Fricke SE
Reproduction in whole or in part is prohibited without the written consent of the Wilhelm Fricke SE company.
All product names mentioned in these Operating Instructions are trademarks of their respective companies.
Printed on paper made from chlorine and acid-free bleached pulp.