Greenwood Air Management SR100R User manual

Installation Instructions
Please read these installation instructions before starting work.
•Warning: The appliance is not intended for use by young children or infirm
persons unless they have been adequately supervised by a responsible person
to ensure that they can use the appliance safety. Young children should be
supervised to ensure that they do not play with the appliance.
•Observe appropriate safety precautions if working on steps or ladders.
Wear eye protection when breaking out wall or window materials etc.
•The fan should not be sited where it would be subject to a direct source
of heat in excess of 40º C.
•When installing wall mounted fans, ensure that there are no buried cables
or pipes in the way. It is recommended that this fan is mounted 1.8m
above floor level.
•A clearance of 75mm to be allowed on at least one side of the fan for the
removal of the internal grille.
Wall mounting (using ED wall duct and EG external grille)
1Loosen the two retaining screws under grille (do not remove screws),
then pull bottom of grille while lifting.
2Cut the duct to width of the plasterboard or tiled wall with slight fall to
exterior. (Make provisions for cable).
3Fill in any gaps with mortar or foam and make good internal and external
walls. Make sure that ducting remains circular and screw holes are horizontal.
4Using No 8 screws, secure fan body to ducting first making sure back
draught shutter is fitted, if required, and electrical cable passes through
as appropriate. Wire fan (see wiring details).
5Replace internal grille by hooking the top of grille onto main body then
push bottom of grille home. Gently tighten retaining screws at bottom of
grille, ensuring no wires are trapped.
6Screw the protective wall grille over the external duct opening.
Ceiling mounting
7Loosen the two retaining screws under grille (do not remove screws),
then pull bottom of grille while lifting.
8Cut an opening through the ceiling for the fan and electrical cable.
9Secure to ceiling using suitable fixing method first making sure
backdraught shutters are removed but shutter spider is left in position.
Wire fan (see wiring details).
10 Place flexible ducting over the spigot of the fan. Fit ducting to spigot
using ties supplied. Maximum duct length to comply with Building
Regulations. Replace front grille.
11 Typical installation ducted through roof soffit.
12 Typical installation ducted through roof to external wall.
Fine Adjustments
If after installation the fan is
not level, the front grille can be
turned up to 5˚ clockwise or
5˚ anti-clockwise to correct this.
Wiring Details
Installation Method 1 13
•Strip cable to correct lengths as shown in diagram 13a.
•Insert cable through cable entry point ➀, then clamp cable using the
cable clamp ➁.
•Use the cable guides ➂to retain the cable wires, then push the wires into
the terminal block ➃until cable comes to a dead stop.
•Peel open the terminal cover, so that terminal screws are visible, then
tighten screws and replace terminal cover, making sure that cover is fully
replaced.
5˚ 5˚
8652 Affresco Silent instr v5 28/7/06 10:32 Page 24
Silent Fan Instructions.indd 24 02/02/2012 18:20

Installation Method 2 14
•Strip cable to correct lengths as shown in diagram 14a.
•Break open cable entry ➄point then insert cable.
•Push the wires into the terminal block ➅until cable comes to a
dead stop.
•Peel open the terminal cover, so that terminal screws are visible, then
tighten screws and replace terminal cover, making sure that cover is fully
replaced.
Wiring Diagrams
The electrical connections must
be carried out by a qualified
electrician in accordance with
IEE or local regulations.
Warning: Isolate electricity
supply before starting work.
The fans are double insulated
and do not require an earth
connection.
The fans must be connected
to a double pole isolating switch
having contact separation of at
least 3mm.
When supplied from a 5 amp
lighting circuit no local fuse is required.
Fan Specification
220V/240V~50Hz. Power Consumption: 10.5W IP24
Cable sizes: Fixed flat wiring 2 core 1mm2
3 core 1/1.5mm2
Air flow rate: 17 L/S
Sound Pressure @ 3 m: 27.1 dB(A)
Timer Adjustment
Warning: Isolate electricity supply before starting work.
15 Remove anti-backdraught shutter spider ➆then PCB cover ➇at rear
end of fan by unscrewing the two PCB cover screws.
•The timer ➈is preset (approximately 20 minutes) but may be adjusted
by using a screwdriver and rotating clockwise to reduce time and
anticlockwise to increase time overrun.
Cleaning and Servicing the Fan
Warning: Always isolate fan from mains supply before cleaning. Do not use
solvents to clean this fan.
•Loosen the two retaining screws under grille (Do not remove screws),
then pull bottom of grille while lifting.
•The fan may now be cleaned using a brush or damp cloth.
Do not immerse in water.
•After cleaning replace internal grille.
Fuse
Double pole
isolating switch
Fanterminal
Light switch
Light
N
L
N
L
L1
Fuse
Double pole
isolating switch
N
L
Fanterminal
Light switch
Light N
L
L1
Timer
Basic
8652 Affresco Silent instr v5 28/7/06 10:32 Page 25
26.7
Installation Method 2 14
•Strip cable to correct lengths as shown in diagram 14a.
•Break open cable entry ➄point then insert cable.
•Push the wires into the terminal block ➅until cable comes to a
dead stop.
•Peel open the terminal cover, so that terminal screws are visible, then
tighten screws and replace terminal cover, making sure that cover is fully
replaced.
Wiring Diagrams
The electrical connections must
be carried out by a qualified
electrician in accordance with
IEE or local regulations.
Warning: Isolate electricity
supply before starting work.
The fans are double insulated
and do not require an earth
connection.
The fans must be connected
to a double pole isolating switch
having contact separation of at
least 3mm.
When supplied from a 5 amp
lighting circuit no local fuse is required.
Fan Specification
220V/240V~50Hz. Power Consumption: 10.5W IP24
Cable sizes: Fixed flat wiring 2 core 1mm2
3 core 1/1.5mm2
Air flow rate: 17 L/S
Sound Pressure @ 3 m: 27.1 dB(A)
Timer Adjustment
Warning: Isolate electricity supply before starting work.
15 Remove anti-backdraught shutter spider ➆then PCB cover ➇at rear
end of fan by unscrewing the two PCB cover screws.
•The timer ➈is preset (approximately 20 minutes) but may be adjusted
by using a screwdriver and rotating clockwise to reduce time and
anticlockwise to increase time overrun.
Cleaning and Servicing the Fan
Warning: Always isolate fan from mains supply before cleaning. Do not use
solvents to clean this fan.
•Loosen the two retaining screws under grille (Do not remove screws),
then pull bottom of grille while lifting.
•The fan may now be cleaned using a brush or damp cloth.
Do not immerse in water.
•After cleaning replace internal grille.
Fuse
Double pole
isolating switch
Fanterminal
Light switch
Light
N
L
N
L
L1
Fuse
Double pole
isolating switch
N
L
Fanterminal
Light switch
Light N
L
L1
Timer
Basic
8652 Affresco Silent instr v5 28/7/06 10:32 Page 25
Installation Method 2 14
•Strip cable to correct lengths as shown in diagram 14a.
•Break open cable entry ➄point then insert cable.
•Push the wires into the terminal block ➅until cable comes to a
dead stop.
•Peel open the terminal cover, so that terminal screws are visible, then
tighten screws and replace terminal cover, making sure that cover is fully
replaced.
Wiring Diagrams
The electrical connections must
be carried out by a qualified
electrician in accordance with
IEE or local regulations.
Warning: Isolate electricity
supply before starting work.
The fans are double insulated
and do not require an earth
connection.
The fans must be connected
to a double pole isolating switch
having contact separation of at
least 3mm.
When supplied from a 5 amp
lighting circuit no local fuse is required.
Fan Specification
220V/240V~50Hz. Power Consumption: 10.5W IP24
Cable sizes: Fixed flat wiring 2 core 1mm2
3 core 1/1.5mm2
Air flow rate: 17 L/S
Sound Pressure @ 3 m: 27.1 dB(A)
Timer Adjustment
Warning: Isolate electricity supply before starting work.
15 Remove anti-backdraught shutter spider ➆then PCB cover ➇at rear
end of fan by unscrewing the two PCB cover screws.
•The timer ➈is preset (approximately 20 minutes) but may be adjusted
by using a screwdriver and rotating clockwise to reduce time and
anticlockwise to increase time overrun.
Cleaning and Servicing the Fan
Warning: Always isolate fan from mains supply before cleaning. Do not use
solvents to clean this fan.
•Loosen the two retaining screws under grille (Do not remove screws),
then pull bottom of grille while lifting.
•The fan may now be cleaned using a brush or damp cloth.
Do not immerse in water.
•After cleaning replace internal grille.
Fuse
Double pole
isolating switch
Fanterminal
Light switch
Light
N
L
N
L
L1
Fuse
Double pole
isolating switch
N
L
Fanterminal
Light switch
Light N
L
L1
Timer
Basic
8652 Affresco Silent instr v5 28/7/06 10:32 Page 25
Installation Method 2 14
•Strip cable to correct lengths as shown in diagram 14a.
•Break open cable entry ➄point then insert cable.
•Push the wires into the terminal block ➅until cable comes to a
dead stop.
•Peel open the terminal cover, so that terminal screws are visible, then
tighten screws and replace terminal cover, making sure that cover is fully
replaced.
Wiring Diagrams
The electrical connections must
be carried out by a qualified
electrician in accordance with
IEE or local regulations.
Warning: Isolate electricity
supply before starting work.
The fans are double insulated
and do not require an earth
connection.
The fans must be connected
to a double pole isolating switch
having contact separation of at
least 3mm.
When supplied from a 5 amp
lighting circuit no local fuse is required.
Fan Specification
220V/240V~50Hz. Power Consumption: 10.5W IP24
Cable sizes: Fixed flat wiring 2 core 1mm2
3 core 1/1.5mm2
Air flow rate: 17 L/S
Sound Pressure @ 3 m: 27.1 dB(A)
Timer Adjustment
Warning: Isolate electricity supply before starting work.
15 Remove anti-backdraught shutter spider ➆then PCB cover ➇at rear
end of fan by unscrewing the two PCB cover screws.
•The timer ➈is preset (approximately 20 minutes) but may be adjusted
by using a screwdriver and rotating clockwise to reduce time and
anticlockwise to increase time overrun.
Cleaning and Servicing the Fan
Warning: Always isolate fan from mains supply before cleaning. Do not use
solvents to clean this fan.
•Loosen the two retaining screws under grille (Do not remove screws),
then pull bottom of grille while lifting.
•The fan may now be cleaned using a brush or damp cloth.
Do not immerse in water.
•After cleaning replace internal grille.
Fuse
Double pole
isolating switch
Fanterminal
Light switch
Light
N
L
N
L
L1
Fuse
Double pole
isolating switch
N
L
Fanterminal
Light switch
Light N
L
L1
Timer
Basic
8652 Affresco Silent instr v5 28/7/06 10:32 Page 25
Installation Method 2 14
•Strip cable to correct lengths as shown in diagram 14a.
•Break open cable entry ➄point then insert cable.
•Push the wires into the terminal block ➅until cable comes to a
dead stop.
•Peel open the terminal cover, so that terminal screws are visible, then
tighten screws and replace terminal cover, making sure that cover is fully
replaced.
Wiring Diagrams
The electrical connections must
be carried out by a qualified
electrician in accordance with
IEE or local regulations.
Warning: Isolate electricity
supply before starting work.
The fans are double insulated
and do not require an earth
connection.
The fans must be connected
to a double pole isolating switch
having contact separation of at
least 3mm.
When supplied from a 5 amp
lighting circuit no local fuse is required.
Fan Specification
220V/240V~50Hz. Power Consumption: 10.5W IP24
Cable sizes: Fixed flat wiring 2 core 1mm2
3 core 1/1.5mm2
Air flow rate: 17 L/S
Sound Pressure @ 3 m: 27.1 dB(A)
Timer Adjustment
Warning: Isolate electricity supply before starting work.
15 Remove anti-backdraught shutter spider ➆then PCB cover ➇at rear
end of fan by unscrewing the two PCB cover screws.
•The timer ➈is preset (approximately 20 minutes) but may be adjusted
by using a screwdriver and rotating clockwise to reduce time and
anticlockwise to increase time overrun.
Cleaning and Servicing the Fan
Warning: Always isolate fan from mains supply before cleaning. Do not use
solvents to clean this fan.
•Loosen the two retaining screws under grille (Do not remove screws),
then pull bottom of grille while lifting.
•The fan may now be cleaned using a brush or damp cloth.
Do not immerse in water.
•After cleaning replace internal grille.
Fuse
Double pole
isolating switch
Fanterminal
Light switch
Light
N
L
N
L
L1
Fuse
Double pole
isolating switch
N
L
Fanterminal
Light switch
Light N
L
L1
Timer
Basic
8652 Affresco Silent instr v5 28/7/06 10:32 Page 25
Installation Method 2 14
•Strip cable to correct lengths as shown in diagram 14a.
•Break open cable entry ➄point then insert cable.
•Push the wires into the terminal block ➅until cable comes to a
dead stop.
•Peel open the terminal cover, so that terminal screws are visible, then
tighten screws and replace terminal cover, making sure that cover is fully
replaced.
Wiring Diagrams
The electrical connections must
be carried out by a qualified
electrician in accordance with
IEE or local regulations.
Warning: Isolate electricity
supply before starting work.
The fans are double insulated
and do not require an earth
connection.
The fans must be connected
to a double pole isolating switch
having contact separation of at
least 3mm.
When supplied from a 5 amp
lighting circuit no local fuse is required.
Fan Specification
220V/240V~50Hz. Power Consumption: 10.5W IP24
Cable sizes: Fixed flat wiring 2 core 1mm2
3 core 1/1.5mm2
Air flow rate: 17 L/S
Sound Pressure @ 3 m: 27.1 dB(A)
Timer Adjustment
Warning: Isolate electricity supply before starting work.
15 Remove anti-backdraught shutter spider ➆then PCB cover ➇at rear
end of fan by unscrewing the two PCB cover screws.
•The timer ➈is preset (approximately 20 minutes) but may be adjusted
by using a screwdriver and rotating clockwise to reduce time and
anticlockwise to increase time overrun.
Cleaning and Servicing the Fan
Warning: Always isolate fan from mains supply before cleaning. Do not use
solvents to clean this fan.
•Loosen the two retaining screws under grille (Do not remove screws),
then pull bottom of grille while lifting.
•The fan may now be cleaned using a brush or damp cloth.
Do not immerse in water.
•After cleaning replace internal grille.
Fuse
Double pole
isolating switch
Fanterminal
Light switch
Light
N
L
N
L
L1
Fuse
Double pole
isolating switch
N
L
Fanterminal
Light switch
Light N
L
L1
Timer
Basic
8652 Affresco Silent instr v5 28/7/06 10:32 Page 25
Silent Fan Instructions.indd 25 02/02/2012 18:20

Greenwood Air Management Ltd.,
Greenwood House, Brookside Avenue,
Rustington, W. Sussex BN16 3LF
United Kingdom
Tel: [phone]. Fax: [phone]
Email: [email protected]
Web: www.greenwood.co.uk
05.10.727 Issue A July 2006
8652 Affresco Silent instr v5 28/7/06 10:32 Page 42
MCR 710 05.10.727 Issue A January 2012
MCR 710 05.10.727 Issue B January 2012
Silent Fan Instructions.indd 42 02/02/2012 18:20