Groz LED-346 User manual

INSTRUCTION MANUAL
S3720, REV A
Worklight
Jump Starter
LED-346
A must have for every car owner!
Jump starts cars up to 3L Gasoline and 2L Diesel
Engines.
Light Output
Poweul multiple output with bright and
balanced illumination.
1ST PRESS 2ND PRESS 3RD PRESS
UV MODE LOW
INTENSITY
HIGH
INTENSITY
LUMEN -280 700
RUN TIME 13.5 hrs 8 hrs 4 hrs
Integrated with
1. 7W COB Work light
2. 1W UV Light (395 nm)
UV light popularly used to detect engine
oil leakage, cracks, AC gas leakage etc.
Sturdy Construction
a. IP 54 Rated
Protected against dust and eects of water
spray from any direction
b. Robust ABS body makes the light usable even
in rugged condition
c. IK 07 Rated
d. Smart Clamp with alligator cables provided
with each light comes with overcharge,
overcurrent, short circuit, reverse polarity, over
temperature and spark free protection
e. Strong magnetic base with hook at top and
bottom for ease of use
2 USB output ports can be used to charge 2
devices simultaneously.
Type C fast charging protected by rubberized
bezel
Peak current : 500 A
Can jump start vehicles upto 15 times on a full
charge
CAT
NR.
SIZE (L×H×D)
(INCH) (MM)
LED/346 13-5/64 × 2-11/64 × 2-3/32 332 × 55 × 53
700 3.5 HRS 395 NM
8 HRS
at lowest intensity
11.1V 7800 mAh
Li-Ion
Power Source
180°
180° Swivelling
Base
1W UV Top Torch
Magnet on base with
hang hook
IP54
IK07
RoHs
NEW!

2
SAFETY INFORMATION
• Follow workshop health & safety rules,
regulations and conditions when using
Worklight with Jump Starter.
• When not in use, Worklight should be
stored in a dry location to inhibit clean and
workable light.
• During their period of use, accessories must
be checked for wear, cracks and other
damage, replace any damaged or worn
parts immediately.
• Use genuine parts only. Unauthorized parts
may be dangerous and will void the warranty.
• Keep the Worklight clean and in good
working order for best and safest
peormance.
• DO NOT use the lamp in the immediate
vicinity of inflammable materials or gases.
• DO NOT point the light directly in your own or
any other person’s or animal’s eyes.
• DO NOT drop, throw or misuse the Worklight
• Eyes protection: Wear a protective mask or
protective eyewear.
• Check that the product has not suered any
damage during transport or storage. Clean
and remove any dust or residual packing
material.
• Read the instructions carefully before
using Worklight and keep them for further
reference.
WARNING!
• DO NOT use this worklight with jump starter
as a battery in place of vehicle’s battery
• DO NOT connect positive and negative
clamps to one another
• DO NOT immerse Worklight in water.
• DO NOT place Worklight near a fire or any
other source of intense heat.
• DO NOT attempt to open, disassemble,
modify or service the Worklight.
• DO NOT expose Worklight to temperatures
above 50°C (122° F).
• DO NOT use Worklight if you suspect that the
batteries or the casing is damaged.
PACKAGE CONTENT
DESCRIPTION QUANTITY
Worklight with Jump Starter 1
USB cable 1
Smart Clamp with alligator cable 1
O.I.P.M. 1
OPERATING INSTRUCTIONS
For Worklight
1. Indicator of mode and battery at the back of
worklight
2. Fully charge the battery before the first use.
To charge, connect the Worklight with the
USB charger cable provided. Connect the
USB charger to the power source.
3. While charging, the 4 green indicator LED at
the back will blink continuously.
4. When the battery is fully charged, all the
indicator LEDs will turn green & stop blinking.
Full charging takes about 4 hours.
5. Press the button located at the back of the
light.
• Once for UV top torch to turn “ON”
• Twice for 280 lumen light to turn “ON”
• Thrice for 700 lumen light to turn “ON”
• Four times to turn “OFF” the light
For Jump Starting Vehicle
1. Indicator of mode and battery at the back of
worklight .
2. Connect the smart clamp cables with
battery’s red to positive and black to
negative terminals.
3. Connect the other port in Worklight.
4. When the two lights in adapter of smart
clamp cables blink green it is ready.
5. Jump start the Car hassle free.
6. If the two lights in adaptor of smart clamp
blink red, check the connections again
This Worklight with Jump Starter can jump start
3L Gasolines Engine and 2L Diesel Engine up to 15
times with single charge
Smart Clamp Functions
Aer connecting smart clamp to worklight, light
indicator on smart clamp must blink green and
red lights.
Follow below steps for handy usage:
1. When light indicator shows Green light
All the connections are right and vehicle can
jump start

3
2. When light indicator shows Red light
There might be a wrong connection, please
reconnect following above instructions
3. When light indicator shows no light but beep
can be heard
Reverse charge is connected, Recheck the
connections
MAINTENANCE
• Clean any dirt from the housing or the lens
immediately, since it could cause overheating.
• If required, clean with a dry or slightly moist
clean cloth. Do not use cleaners that contain
abrasives or solvents.
• When not in use, Worklight should be stored in
a dry location
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The Worklight has low lumen output or does not work. Low battery Recharge the battery
If the Worklight still doesn't work -Contact nearest authorized service dealer
If the Jump starter is not starting car Low battery Recharge the battery
If the Jump Starter still doesn’t work Battery degraded Replace battery or visit nearest workshop
When connecting alligator cables to battery
connections and smart clamp is beeping
Reverse connection Change the connections at battery ends
DISPOSAL
The components or the used products must be given to companies that specialize in the disposal and
recycling of industrial waste.

Groz Engineering Tools Pvt. Ltd.
Groz Net Industries
Village Kherki Daula, National Highway-8,
Gurugram-122001, Haryana, INDIA
Tel [phone]
Fax [phone]
E-Mail [e-mail]
Url www.groz-tools.com
The GROZ name, GROZ logo and the mark are
trademarks of GROZ Engineering Tools Pvt. Ltd., India