GSD WCT2GM2511 User manual

Hui Zhou Gaoshengda Technology Co., LTD WCT2GM2511
PAGE 1 OF 5
Version 1.0
WIFI+BT Module
IEEE 802.11 a/b/g/n/ac 2T/2R
Model Number: WCT2GM2511
Product Descrition
The WCT2GM2511 is a complete dual-band(2.4GHz and 5GHz)WIFI 2×2 MIMO module. This module provides a
high level of integration with a dual-stream IEEE 802.11ac MAC/ base band /radio and Bluetooth 5.1.The WLAN
operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps. It fully complies with IEEE
802.11 a/b/g/n/ac feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput
from an extended distance.
Product Features
Product Specification
Model
WIF+BT Module
Product Name
WCT2GM2511
Standard
802.11 a /b/g/n/ac
Interface
USB
Data Transfer Rate
1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 866.7Mbps
Modulation Method
GFSK,π/4-DQPSK,8DPSK(bluetooth)
DQPSK,DBPSK,CCK(802.11b)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)
QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)
Frequency Band
BLUETOOTH
2402~2480 MHz
WIFI
2.4G: 2412~2462 MHz
5G: 5150~5350MHz,5470~5725MHz,5725~5850MHz
Operation Mode
Infrastructure
Security
WEP, TKIP, AES, WPA, WPA2
Operating Voltage
5V±10%
Current Consumption
＜1000mA
Antenna Type
PCB
Operating
Temperature
0 ~ 70°C ambient temperature
Storage Temperature
-40 ~ 80°C ambient temperature
Humidity
5 to 95 % maximum (non-condensing)
◆Complies with IEEE 802.11b/g/n for 2.4GHz and IEEE 802.11a/n/ac 5GHz Wireless LAN.
◆Bluetooth v5.1
◆Two transmit and Two receive path(2T2R)
◆Works with all existing network nfrastructure.
◆Capable of up to 128-Bit WEP Encryption.
◆Freedom to roam while staying connected.
◆UP to 866.7 Mbps High-Speed Transfer Rate in 802.11ac mode of operation.
◆Operating Systems：Linux,Win7, Win8, Win10,XP
◆Low power consumption.
◆Easy to install and configure.
◆High speed USB 2.0 interface
◆ROHS compliant

Hui Zhou Gaoshengda Technology Co., LTD WCT2GM2511
PAGE 2 OF 5
Version 1.0
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Please notice that if the FCC identification number is not visible when the module is
installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior label
can use wording such as the following: “Contains FCC ID:2AC23-WCT2G” any similar wording
that expresses the same meaning may be used.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.

Hui Zhou Gaoshengda Technology Co., LTD WCT2GM2511
PAGE 3 OF 5
Version 1.0
The device must be professionally installed
The intended use is generally not for the general public.It is generally for industry/commercial use.
The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not
normally required. the user has no access to the connector.
Installation must be controlled. Installation requires special training
This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and
CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
The module is limited to OEM installation ONLY.
The OEM integrator is responsible for ensuring that the end-user has no manual instruction
to remove or install module.
The module is limited to installation in mobile application.
A separate approval is required for all other operating configurations, including portable
configurations with respect to Part 2.1093 and difference antenna configurations.
There is requirement that the grantee provide guidance to the host manufacturer for
compliance with Part 15B requirements.
The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval.
Trace antenna designs: Not applicable.
Antennas:
2.4G
5G
PCB antenna & 3 dBi
PCB antenna & 4 dBi
BT Antenna:
BRADE
TYPE
GAIN
GSD
PCB antenna
2 dBi
The antenna is permanently attached, can’t be replaced.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
Please notice that if the ISED certification number is not visible when the module is
installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior label
can use wording such as the following: “Contains IC:12290A-WCT2G” any similar wording
that expresses the same meaning may be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du

Hui Zhou Gaoshengda Technology Co., LTD WCT2GM2511
PAGE 4 OF 5
Version 1.0
module
d'Industrie Canada, précédé des mots « Contient un module d'émission », du mot « IC:12290A-
WCT2G » ou d'une formulation similaire exprimant le même sens, comme suit
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102
and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure
and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de
RSS 102 etla conformitéàl'exposition de RSS-102 RF, utilisateurs peut obtenir l'information
canadienne surl'exposition et la conformitéde rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placéou ne fonctionnant en même temps qu'aucune autre antenne
ouémetteur. Cet équipement devrait être installéet actionnéavec une distance minimum de 20
centimètres entre le radiateur et votre corps.
Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of
mobile, which means the device is installed and used at distances of at least 20cm from
persons.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related
to the transmitter as show in this manual(FCC/ICanada statement).
Host manufacturer is responsible for compliance of the host system with module installed
with all other applicable requirements for the system such as Part 15 B, ICES 003.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements
for the transmitter when the module is installed in the host.

Hui Zhou Gaoshengda Technology Co., LTD WCT2GM2511
PAGE 5 OF 5
Version 1.0
The use condition limitations extend to professional users, then instructions must state
that this information also extends to the host manufacturer’s instruction manual. This
module is stand-alone modular. If the end product will involve the Multiple simultaneously
transmitting condition or different operational conditions for a stand-alone modular
transmitter in a host, host manufacturer have to consult with module manufacturer for the
installation method in end system.
Any company of the host device which install this modular should perform the test of radiated
&
condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209
&
15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247
and
15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part
15.247
and 15.407) listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular
transmitter
grant of certification.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED
requirements for the transmitter when the module is installed in the host.
Must have on the host device a label showing Contains FCC ID:2AC23-WCT2G and IC:12290A-WCT2G
Installer should put it in the manual：
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc
/ (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé
à une distance d'au moins 20 cm de personnes.
le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de
conformité relatives à l'émetteur que de montrer dans ce manuel.
le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module
installé avec toutes les autres exigences applicables du système comme la partie 15 b, ices
- 003.
accueillir le fabricant est fortement recommandé de confirmer la conformité avec les
exigences de la fcc / (émetteur lorsque le module est installé dans l'hôte.
le dispositif d'accueil doivent avoir une étiquette indiquant contient IC:12290A-WCT2G Les
personnes chargées de l'installation devraient figurer dans le manuel:
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable
aux systèmes de satellites mobiles utilisant les mêmes canaux.
Doit avoir sur l'appareil hôte une étiquette indiquant Contient l'ID FCC ID:2AC23-WCT2G
et IC:12290A-WCT2G