Gsm Idea moving led 100 User manual

10.1.LERLAUNAMS’

M O VINGHEAD

IDEA M O VING

LED 100

SGM IT

Idea Moving Led 100 XM335-V1.1-A

PULIZIA E MANUTENZIONE

I seguenti punti devono essere tenuti in considerazione durante l’ispezione:

1. Tutte le viti per installare l’apparecchio o parti dell’apparecchio devono essere strette saldamente e

non devono essere corrose.

2. Non ci deve essere nessuna deformazione sul corpo, sulle lenti a colori, sui punti di fissaggio e di

installazione (soffitto, sospensione, trussing).

3. Parti meccaniche in movimento non devono mostrare tracce di usura e non devono ruotare in modo

sbilanciato.

4. I cavi di alimentazione non devono mostrare segni di danni, di usura del materiale o sedimenti

Ulteriori istruzioni basate sul punto di installazione e d’utilizzo devono essere eseguite da un installatore

esperto ed ogni problema relativo alla sicurezza deve essere eliminato.

ATTENZIONE!

Scollegare dall’alimentazione prima di iniziare lavori di manutenzione.

Per mantenere le luci in buone condizioni ed estendere il tempo di vita, raccomandiamo una pulizia regolare

delle luci.

1. Pulire le lenti dentro e fuori ogni settimana per evitare la debolezza delle luci dovuta ad accumulo di

polvere

2. Pulire la ventola ogni settimana

3. Un controllo elettrico dettagliato da un ingeniere elettrico approvato ogni tre mesi, assicurarsi che i

contatti del circuito siano in buone condizioni, prevenire il cattivo contatto del circuito da

surriscaldamento.

Raccomandiamo una pulizia frequente dell’apparecchio. Per piacere usare un panno morbido umido e senza

peli. Non usare mai alcool o solventi!

Non ci sono parti utilizzabili nell’apparecchio eccetto la lampada. Per piacere fare riferimento alle istruzioni

sotto la voce “Istruzioni per l’installazione”. Se si dovesse aver bisogno di pezzi di ricambio, per piacere

ordinare parti originali dal proprio rivenditore locale.

CARATTERISTICHE TECNICHE

Alimentazione: 100V~240V AC，50 Hz /60Hz

Consumo d’energia: max. 230W

Dimensioni dell’imballo: 35x29.5x43cm

Peso netto: 7.6KG

Peso lordo: 10KG

Nota: sono esclusi errori ed omissioni per ogni informazione data in questo manuale. Ogni informazione è

soggetta a modifica senza preavviso.

Vi ringraziamo per aver acquistato un prodotto SGM.

Per ottenere i migliori risultati dal suo utilizzo, vi preghiamo di leggere attentamente questo manuale di istruzioni.

Al suo interno troverete le informazioni tecniche e le specifiche d’uso del prodotto. Nelle pagine in appendice tro-

verete inoltre schemi e diagrammi destinati all’assistenza tecnica.

Nell’ottica di qualità SGM, è possibile che l’Azienda apporti migliorie ai suoi prodotti, per cui consigliamo di alle-

gare il manuale al prodotto stesso e di trascrivere il numero di serie nell’ultima pagina della copertina: utilizzando

il presente manuale con un apparecchio fabbricato prima o dopo la sua stampa, potrebbero esserci discrepanze

fra l’apparecchio e quanto riportato nel manuale stesso.

Thank you for buying an SGM product.

To obtain the best results, please carefully read this instruction manual in which you will find technical information

and specifications for use of the product, as well as diagrams for technical service in the appendix.

In light of SGM quality, the company may make improvements to its products. Therefore, we recommend that the

manual be attached to the product and the serial number copied onto the back cover: using this manual with

equipment manufactured before or after its printing, might show discrepancies between the equipment and the

information listed in the manual.

Wir danken Ihnen für den Kauf eines Produkts von SGM.

Zur Erzielung der besten Resultate bei der Benutzung bitten wir Sie, die vorliegende Bedienungsanleitung aufmerk-

sam zu lesen. Darin finden Sie die technischen Informationen sowie die Anweisungen für die Benutzung des

Produkts. Im Anhang befinden sich auBerdem die Schaltpläne undv Diagramme für den Kundendienst.

SGM behält sich das Recht vor, Verbesserungen an den Produkten vorzunehmen und deshalb empfehlen wir, die

Bedienungsanleitung dem Produkt stets beizulegen und die Seriennummer auf der letzten Seite des Umschlags

einzutragen. Bei der Verwendung dieses Handbuches mit einem Gerät, das vor oder nach der Drucklegung produ-

ziert wurde, können sich Abweichungen zwischen Gerät und dem Inhalt des Handbuches ergeben.

Nous vous remercions d’avoir acheté un produit SGM.

Pour optimiser son utilisation, nous vous prions de bien vouloir lire attentivement cette notice où vous trouverez

les informations techniques et les caractéristiques d’utilisation du produit. En outre, vous trouverez également,

dans les pages en appendice, les schémas et les diagrammes concernant l’assistance technique.

Le concept de qualité SGM, lui permet d’améliorer continuellement ses produits et c’est pourquoi nous vous con-

seillons de joindre la notice au produit et d’inscrire le numéro de sèrie sur la page de couverture. En effet, si on

l’utilise avec un appareil fabriqué avant ou après son impression, il peut y avoir des différences entre l’appareil et

ce qui figure dans la notice.

Les estamos sumamente agradecidos por haber elegido un producto SGM.

Para obtener los mejores resultados, les rogamos leer detenidamente el presente manual de instrucciones. El

mismo contiene las informaciones técnicas y las indicaciones de uso del producto. Las páginas anexas contienen

además los esquemas y diagramas necesarios para la asistencia técnica.

Para mantener la calidad SGM, es posible que la Empresa aporte mejoras sus productos, por ello les aconsejamos

conservar el manual junto con el aparato correspondiente y escribir su número de serie en la última página del

manual; si en cambio se utiliza el presente manual con un aparato frabicado antes o después de su impresión, es

probable que existan discrepancias entre el aparato y las indicaciones del mismo.

GB SGM

XM335-V1.1-A Idea Moving Led 100

Table of Contents

INTRODUCTION: .............................................................................................................................................

Features..................................................................................................................................................

OVERVIEW......................................................................................................................................................3

SAFETY INSTRUCTIONS ...................................................................................................................................4

GENERAL GUIDELINES .....................................................................................................................................5

INSTALLATION INSTRUCTIONS .........................................................................................................................5

Mounting the device .................................................................................................................................5

Installation method via clamp ....................................................................................................................6

DMX-51 control connection ......................................................................................................................6

Control Board ..........................................................................................................................................9

FUNCTION MODE...........................................................................................................................................10

DMX address setting...............................................................................................................................10

Slave setting .........................................................................................................................................10

Auto Program ........................................................................................................................................10

Music control .........................................................................................................................................10

INFORMATION...............................................................................................................................................11

Time information....................................................................................................................................11

Software version ....................................................................................................................................11

PERSONALITY ...............................................................................................................................................11

Status Settings ......................................................................................................................................11

SERVICE SETTING .........................................................................................................................................1

Fans Control ..........................................................................................................................................1

Display Setting ......................................................................................................................................1

Temperature C/F ....................................................................................................................................1

Initial effect...........................................................................................................................................1

Wireless DMX.........................................................................................................................................1

RESET-FUNCTIONS ........................................................................................................................................13

EFFECT ADJUST.............................................................................................................................................13

Test function of each channel...................................................................................................................13

Lamp adjustment ...................................................................................................................................13

Calibrate values .....................................................................................................................................13

USERS MODE SET..........................................................................................................................................13

User mode ............................................................................................................................................13

Preset User mode...................................................................................................................................13

EDIT PROGRAM .............................................................................................................................................13

Select program ......................................................................................................................................13

Edit program .........................................................................................................................................13

Edit scenes............................................................................................................................................13

Auto scenes rec. ....................................................................................................................................13

INSTRUCTIONS ON USE .................................................................................................................................16

ERROR MESSAGE ..........................................................................................................................................17

CLEANING AND MAINTENANCE .......................................................................................................................18

TECHNICAL SPECIFICATIONS..........................................................................................................................18

SGM GB

Idea Moving Led 100 XM335-V1.1-A

KEEP THIS MANUAL FOR FUTURE NEEDS

For your own safety, please read this user manual carefully before installing the device.

CAUTION !

Keep this device away from rain and moisture!

Unplug mains lead before opening the housing

Every person involved with the installation, operation and maintenance of this device has to:

be qualified

follow carefully the instructions of this manual

INTRODUCTION:

Thank you for having chosen this professional moving head.

You will see you have acquired a powerful and versatile device.

Unpack the device. Inside the box you should find: the fixture device, an XLR connection cable, one omega

clamps and a safety rope and this manual. Please check carefully that there is no damage caused by

transportation. Should there be any, consult your dealer and don’t install this device.

Feat res

60pcs LEDS: x3W red, 17x3W green, 15x3W blue, 6x3W white

Extremely Long Life:50,000 Hr and low power consumption

DMX channel:13 channels

Pan/tilt movement: - 8 bit and 16 bit resolution

- For smooth and precise resolution

- Pan: 540°/630° optional, Tilt: 65°movement

- High speed of pan/tilt movement, speed of pan/tilt movement is adjustable

- Scan position memory, auto reposition after unexpected movement

Strobe effect with 18 flashes per second and pulse effect

General dimming and blackout for all four colors

Excellent color mixing and rainbow effect

Friendly blue LCD display

Preset program: 7 built in programs can be called up via DMX controller

GB SGM

XM335-V1.1-A Idea Moving Led 100

OVERVIEW

5 6 7 8

1. Lens

. Yoke

3. Base

4. Wireless DMX antenna

5. LCD-Display

6. Mode/esc-button

7. Up-button

8. Down-button

9. Enter-button

10. Microphone

11. Housing

1 . 3-PIN DMX output socket

13. 3-PIN DMX input socket

14. 5-PIN DMX output socket

15. 5-PIN DMX input socket

16. Power switch

17. Fuse

18. Power supply

SGM GB

Idea Moving Led 100 XM335-V1.1-A

SAFETY INSTRUCTIONS

CAUTION

Be careful with your operations. With a dangerous voltage you can Suffer a

dangerous electric shock when touching wires!

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe

operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written

in this user manual.

IMPORTANT

Damages caused by the disgregard of this user manual are not subject to warrenty.

The dealer will not accept liability for any resulting defects or problems.

If the device has been exposed to temperature changes due to environmental changes, do not switch it on

immediately. The arising condensation could damage the device. Leave the device switched off until it has

reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,

replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power

cord by the plug. Never pull out the plug by tugging the power cord.

During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily

mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth

air flow, so there should be no shelter for fans and ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the

manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

CAUTION

Never touch device during operation!

The housing may heat up.

Never look directly into the light source,

as sensitive persons may suffer an epileptic shock.

Please be aware that damages caused by manual modifications to the device are not subject to warranty.

Keep away from children and non-professionals.

GB SGM

XM335-V1.1-A Idea Moving Led 100

GENERAL GUIDELINES

This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.

This fixture is only allowed to be operated with the max alternating current which stated in the technical

specifications in the last page of this manual, the device was designed for indoor use only.

Lighting effects are not designed for permanent operation. Consistent operational breaks may ensure that

the device will fanction properly for a long time.

Do not shake the device.Avoid brute force when installing or operating the device.

The device shall only be used complete with its protective shield.

While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,

moisture or dust. The minimum distance between light-output from the projector and the illuminated

surface must be more than 0.5 meter.

Always fix the fixture with an appropriate safety cable if you use the quick lock cam in hanging up the fixture,

please make sure the quick lock fasteners turned in the quick lock holes correctly.

If you use the quick lock cam in hanging up the fixture, please make sure the quick lock fasteners turned

in the quick lock holes correctly.

Operate the device only after having familiarized with its functions. Do not permit operation by persons not

qualified for operating the device. Most damages are the result of unprofessional operation.

Please use the original packaging if the device is to be transported.

For safety reasons, please be aware that all modifications on the device are forbidden.

If this device will be operated in any way different to the one described in this manual, the product may

suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to

short-circuit, burns, electric shock, lamp explosion, crash, etc.

INSTALLATION INSTRUCTIONS

Mo nting the device

CAUTION

Pleas consider the EN 60598- -17 and the other respective national norms

during the installation. The installation must only be carried out by a

qualified person.

The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for

1 hour without any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate safety

rope.

Never stand directly below the device when mounting, removing or servicing the fixture.

The operator has to make sure the safety relating and machine technical installations are approved by an

expert before taking the device into operation for the first time.

These installations have to be approved by a skilled person once a year.

Ca tions:

The effect should be installed outside areas where persons may reach it, walk by or be seated.

Overhead mounting requires extensive experience, including amongst others calculating working load limits,

installation material being used, and periodic safety inspection of all installation material and the device. If

you lack these qualifications, do not attempt the installation yourself. Improper installation can result in

bodily injury.

CAUTION

The electric connection must only be carried out by a qualified electrician.

SGM GB

Idea Moving Led 100 XM335-V1.1-A

Before mounting make sure that the installation area can hold a minimum point load of 10 times the device’s

weight.

Connect the fixture to the mains with the power plug.

Installation method via clamp

Please refer to the picture below:

Screw one clamp each via a M1 screw and nut onto the Omega holders.

Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the

device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder.

Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a safe

fixation spot. Insert the end in the carabine and tighten the safety screw.

DMX-512 control connection

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the

male 3-pin XLR input of the moving head. You can chain multiple

Moving head together through serial linking. The cable needed should be two core, screened cable with XLR

input and output connectors. Please refer to the diagram below.

GB SGM

XM335-V1.1-A Idea Moving Led 100

Address 7 Address14 Address 1

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,

such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of

the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 1 0 Ω resistor

connected between pins and 3,which is then plugged into the output XLR socket of the last fixture in the

chain. Please see illustrations below.

PIN 3

PIN 2

120

Projector DMX starting address selection

All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture

responds to the correct control signals. This digital starting address is the channel number from which the

fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of

this starting address is achieved by setting the correct number on the display located on the base of the

device.

You can set the same starting address for all fixtures or a group of fixtures, or make different address for

each fixture individually.

If you set the same address, all the units will start to “listen” to the same control signal from the same

channel number. In other words, changing the settings of one channel will affect all the fixtures

simultaneously.

If you set a different address, each unit will start to “listen” to the channel number you have set, based on

the quantity of control channels of the unit. That means changing the settings of one channel will affect only

the selected fixture.

In the case of the moving head, which is 13 channels fixture when you select the standard channel mode,

you should set the starting address of the first unit to 1, the second unit to 14(13 + 1), the third unit to 7

(13+ 14), and so on.

SGM GB

Idea Moving Led 100 XM335-V1.1-A

Operting instr ctions of the internal DMX wireless system

1. Equipments:

DMX 51 controller, wireless transmitter, and the fixtures with wireless receiver.

. Message from the LED indicator:

1. Rapid flashing red/Green: logging in to a transmitter

. Slow flashing Red/Green: Logged on a transmitter and the DMX line is idle (No DMX is connected to

transmitter).

3. Solid Green: Logged on to a transmitter and receiving DMX data.

4. Solid Red: Not logged on to a transmitter (free)

3. WDMX in the menu of the fixture:

On a fixture installed with wireless system, in order to switch between wireless control system and

traditional DMX control (with cable), a new menu WDMX is added to the display board.

ON: (Activate WDMX)

1. When the fixture is on power，and the WDMX is activated to ON status, but did not connect to the

controller and did not log in to the transmitter, the fixture will search for the DMX signal source. If the

fixture is connected to the DMX controller it can be controlled by DMX controller; if it is log in to the

wireless transmitter, it can be controlled by the Transmitter

. When the fixture is power off, and the WDMX is in ON status, if the fixture is connected to DMX

controller. After the fixture is power on, it can be controlled only by the DMX controller which

connected. The fixture can log in the wireless transmitter, and receive only radio signal from

transmitter, but not DMX from the transmitter.

OFF: (De-activate WDMX)

In this status, wireless system is not activated, so the fixture can not log in the transmitter.

REST: (reset WDMX memory);

Can remove the fixture from the connection with the transmitter, the fixture become free and ready

to log in any transmitter.

4. Setup the wireless system:

1. Connect the transmitter with the DMX controller

. To make the fixture installed with wireless receiver log in to the transmitter

a) Initially, the indicator on the receiver fixture should be in Solid red

b) Press and hold the configuration button on transmitter for less than 3 seconds the red/green

LEDs on the transmitter and the receiver fixture will flash rapidly for about 5~ 10 seconds while

the system goes through its setup procedure.

c) Once the receiver fixture is logged in to the transmitter (T1), the fixture with wireless receiver

will keep the memory, even if restart the power, this unit will log in the transmitter (T1)

automatically.

3. Use the DMX 51 to control the fixture

5. Remove the receivers from transmitter (T1) and to log in to another transmitter (T )

Case 1: Remove a receiver:

a) On the control board of the fixture, enter menu to activated the function of REST;

b) The LED for wireless on the fixture should turn to Solid red; the receiver can log out from the

transmitter (T1);

c) press the configuration button on transmitter(T ) for less than 3 second, then the fixture will start to

connect with the transmitter(T )

Case : Remove all receivers from a transmitter (T1) to log in to T ;

Press and hold the configuration button on the T1 as least 5 seconds, can clear the connection with

all the fixtures.

All the red/green LEDs on the receiver fixtures will turn to Solid red to indicate that the receivers are

unassigned and removed from the transmitter ( T1);

Press and hold the configuration button on the T less then less than 3 second , the fixtures will

connect with the T

PS:

1. Please log the receivers out from the transmitter after every job, so that the receivers are in free un

assigned state and ready to be assigned to a transmitter.

. Do not connect the fixture which is under the communication of wireless system to the DMX controller,

otherwise it will cause interference from the DMX controller.

GB SGM

XM335-V1.1-A Idea Moving Led 100

Control Board

The

Control Board offers several features: you can simply set the starting address, switch on and off the

lamp, run the pre-programmed program or make a reset.

The main menu is accessed by pressing the Mode/esc-button until the display starts flashing. Browse

through the menu by pressing the Up-button or Down-button. Press the Enter-button in order to select the

desired menu. You can change the selection by pressing the Up-button or Down-button. Confirm every

selection by pressing the Enter-button. You can leave every mode by pressing the Mode/esc-button. The

functions provided are described in the following sections.

To access display Men via the internal battery, press the UP & DOWN b ttons sim ltaneo sly.

Display will a tomatically switch off after abo t 10 seconds from last b tton press.

Default settings shaded

Function Mode

Set Dmx Address

Value Display

Set To Slave

Auto Program

Music Control

A001~AXXX

PAN……

Slave1,Slave ,Slave3

Master / Alone

DMX address setting

DMX value display

Slave setting

Auto program

Music control

Time Information Current Time

Total Life Hours

Last Run Hours

Timer Password

Clear Last Run

XXXX(Hours)

Password=XXX

ON/OFF

Power on running time

Fixture running time

Fixture Last times clear

Timer Password

Clear Fixture Last time

Temperature Info Head Temperature XXX℃/℃ Temperature in the head

Information

Software Version Ver1.0 Software version of each IC

Status Settings Address via DMX

No DMX Status

Pan Reverse

Tilt Reverse

Fine Resolution

Pan Degree

Feedback

Movement Speed

Mic Sensitivity

ON/OFF

Close/Hold/Auto/Music

ON/OFF

630/540

ON/OFF

Speed 1~ 4

0~99%

Add. via DMX

Auto run if no DMX

Pan Reverse movement

Tilt Reverse movement

Fine resolution switch

Pan Degree Select

Movement Feedback switch

Movement Mode Select

Sensitivity of Mic.

Service Setting Service Password

Fan Voltage

Password=XXX

High/Low

Service Code“=050”

Fan Voltage Select

Fans Control Auto Fans Speed

High Fans Speed

Low Fans Speed

Fans Speed Mode Select

Display Setting Shutoff Time Display shutoff time

Temperature C/F Celsius

Fahrenheit

Temperature switch between

℃/℃

Initial Effect PAN…… PAN =XXX Initial effect position

Wireless DMX De-Act WDMX

Activate WDMX

Act & Data Out

Rest WDMX Mem

De-activate WDMX

Activate WDMX

Act & Data Out

Reset Wireless DMX Mem

Personality

Reset Default ON/OFF Restore factory sett.

Reset

Function

Reset All

Reset Pan&Tilt

Reset all motors

Reset Pan/Tilt

SGM GB

Idea Moving Led 100 XM335-V1.1-A

Test Channel PAN …… Test function

Manual Control PAN

PAN =XXX

Fine adjustment of the lamp

Effect Adjust

Calibrate Values --Password--

PAN

Password=XXX

PAN=XXX

Calbrate and adjust the

effects to standard/right

position Password “050”

User Mode XXXXXX(Band)

User Mode A

User Mode B

User Mode C

User’s mode to change

channel numbers

Users Mode Set

Edit User Mode PAN

PAN = CH01

Preset User modes

Select Programs Auto Pro Part 1

Auto Pro Part

Auto Pro Part 3

Program 1 ~ 10 Program 1

Program 1 ~ 10 Program

Program 1 ~ 10 Program 3

Select programs to be run

Edit Program Program 1

Program 10

Program Test

Step 01=SCxxx

Step 64=SCxxx

(“STEP

XX”)

Testing program

Program in loop

Save and exit

Edit Scenes Edit Scene 001

~ Edit Scene

Pan,Tilt,……

--Secne Time--

Input By Outside

Pan=xxx…

…

TIME=xx.x

Save and automatically

return

manual scenes edit

Edit Program

Rec. Controller XX~XX Automat. scenes rec

FUNCTION MODE

DMX address setting

With this function, you can adjust the desired DMX-address via the Control Board.

Select “Set DMX address” via the encoder.

Press the encoder, adjust the DMX address by turning the encoder.

Press the encoder to confirm.

Press the Mode/Esc-button in order return to the main menu.

Display the DMX 512 val e of each channel

With this function you can display the DMX 51 value of each channel. The display automatically shows the

channel with a value changing.

Slave setting

With this function, you can define the device as slave.

A to Program

With this function, you can run the internal program. You can select the desired program under “Select

program”. You can set the number of steps under “Edit program”. You can edit the individual scenes

under “Edit scenes”. With this function, you can run the individual scenes either automatically, i.e. with the

adjusted Step-Time.

M sic control

With this function, you can run the internal program sound-controlled.

GB SGM

XM335-V1.1-A Idea Moving Led 100

INFORMATION

Time information

C rrent Time

With this function, you can display the temporary running time of the device from the last power on. The

display shows “XXXX”, “XXXX” stands for the number of hours. The counter is resetted after turning the

device off.

Total life Ho rs

With this function, you can display the running time of the device. The display shows “XXXX”, “XXXX” stands

for the number of hours.

Last R n Ho rs

With this function, you can display last the running time of the lamp. The display shows “XXXX”, “XXXX”

stands for the number of hours.

Time Password

With this function, you can display the timer password. The time password is 038.

Clear Last R n

With this function, you can clear last run time of the fixture. The display shows “ON” or “OFF”, Press “Enter”

to confirm.

Temp. Info.

Head Temp

With this function you can display the temperature on the display board of the base (near CMY-filter) in

Celsius.

Software version

With this function, you can display the software version of the device.

Select “Software version” by turning the encoder.

Press the encoder, the display shows “V-X.X”, “X.X” stands for the version number, e.g. “V-1.0”,

“V- .6”.

Turn the encoder in order to read the version of every individual IC.

Press the Mode/Esc-button in order to return to the main menu.

PERSONALITY

Stat s Settings

Address via DMX

With this function, you can adjust the desired DMX-address via an external controller.

Select “Address via DMX” by turning the encoder.

Press the encoder, the display shows “ON” or “OFF”.

Turn the encoder to select “ON” if you wish to enable this function or “OFF” if you don’t.

Press the encoder to confirm.

Press the Mode/Esc-button in order to return to the main menu.

On the controller, set the DMX-value of channel 1 to "7".

Set the DMX-value of channel to "7"or "8". When set to "7" you can adjust the starting address between

1 and 55. When set to "8" you can adjust the starting address between 56 and 511.

Set the DMX-value of channel 3 to the desired starting address. If you want to set the starting address

to 57, set channel 1 to "7", channel to "7" and channel 3 to "57". If you want to set the starting address

to 4 0,set channel 1 to "7", channel to "8" and channel 3 to "164" ( 56+164=4 0).

Wait for approx. 0 seconds and the unit will carry out a reset. After that, the new starting address is set.

SGM GB

Idea Moving Led 100 XM335-V1.1-A

No DMX Stat s

With this function, when the drive is not DMX signal, it runs automatism, close, hold and music, the default

is hold.

Pan Reverse

With this function you can reverse the Pan-movement.

Tilt Reverse

With this function you can reverse the Tilt-movement.

Fine resol tion

With this function, you can fine resolution switch of pan movement or tilt movement.

Pan Degree

With this function, you can select pan degree for 630 or 540.

Feedback

With this function, you can feedback switch of pan movement or tilt movement.

Movement Speed

With this function, you can select scan mode from 1 to 4.

Mic Sensitivity

With this function, the default is 70%, you can select the desired microphone sensitivity from 0 % to 99 %.

SERVICE SETTING

Service Password

With this function, you can set the service password.

Fan Voltage

With this function, you can select fan voltage for high or low, the default is low

ATTENTION!!

The model is not recommended when ambient temperature is higher than

15 Celsius degree.

Fans Control

With this function, you can set the speed of the running fans. The selections have Auto、high and low.

Display Setting

Sh t off time

With this function you can shut off the LCD display after to 59 minutes. Turn the encoder in order to select

the desired shut off time.

Temperat re C/F

With this function, Display the temperature for Celsius or Fahrenheit.

Initial effect

With this function, Display initial effect position.

Wireless DMX

From factory, this projector is prepared for wireless data transmission (W-DMX). If you wish to de-activate

W-DMX control, you can select the function “De-activate WDMX” by turning the encoder. With the function

“rest”, you can log out the projector from the wireless sender.

Reset Defa lt

With this function, you can select restore factory set for ON or OFF, the default is OFF.

GB SGM

XM335-V1.1-A Idea Moving Led 100

RESET-FUNCTIONS

With this function you can reset the device via the Control Board. You can select the different reset functions

by turning the encoder.

EFFECT ADJUST

Test f nction of each channel

With this function you can test each channel on its (correct) function.

Lamp adj stment

With this function, you can adjust the lamp more easily. All effects will be canceled, the shutter opens and

the dimmer intensity will be set to 100 %. With the individual functions, you can focus the light on a flat

surface (wall) and erform the fine lamp adjustment.

Calibrate val es

With this function, you can calibrate and adjust the effect wheels to their correct positions. The password

of calibrate values is 050.

USERS MODE SET

In this menu, user can select different channels list by different sequence:

For example, after the user enter this manual, if select Auto Program = CH , means in this User’s mode,

the “Dimmer” is in Channel 16.

User mode

With this function, you can create user defined channel orders.

Preset User mode

With this function, you can adjust the rest user defined channel order.

EDIT PROGRAM

Select program

With this function, you can select the program for the Program Run.

Edit program

With this function, you can edit the internal programs.

Edit scenes

With this function, you can edit the scenes of the internal programs.

A to scenes rec.

The moving head features an integrated DMX-recorder by which you can transmit the programmed scenes

from your DMX-controller to the moving head. Adjust the desired scene numbers via the encoder (from – to).

When you call up the scenes at your controller, they will automatically be transmitted to the moving head.

Exc rsion:

A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master unit can start 3 different

Slave units, which run 3 different programs. The Master unit sends the 3 program parts in a continuous loop.

The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned

to. If e.g. a Slave unit is set to “Slave 1” in the menu “Set to Slave”, the Master unit sends “Auto Program

Part 1” to the Slave unit. If set to “Slave ”, the Slave unit receives “Auto Program Part ”.

SGM GB

Idea Moving Led 100 XM335-V1.1-A

To start a Auto Program please proceed as follows:

1. Slave-Setting

Select “Function Mode” by turning the encoder.