guide craft G97300 User manual

G97300, G97301, G97302
1

Guidecraft • 55509 Highway 19 West, Winthrop, MN 55396 • [phone] • www.guidecraft.com
G97300, G97301
Roll Top Desk
Assembly Instructions
Page 2 of 5
A(4)
B(4)
F
C(10)
D(10)
2"
(50mm)
1"
(30mm)
E(22)
.5"
(12mm)
M O
K
L
V G
N
P
Y
T
U
Q
R
Z
2

Guidecraft • 55509 Highway 19 West, Winthrop, MN 55396 • [phone] • www.guidecraft.com
G97300, G97301
Roll Top Desk
Assembly Instructions
Page 3 of 5
T
U
U
Q
R
Q
R
Place cam pins (C) into holes shown above. Firmly
tighten all cam pins.
Place cam nuts (D) into holes on Parts T and U so that
the arrow on the cam face is lined up with the opening.
Once Parts T and U are attached to Parts Q and P, tighten cam nuts
by turning clock-wise until they’ve locked into place.
T
C
C
D
D
3
1
2
3

Guidecraft • 55509 Highway 19 West, Winthrop, MN 55396 • [phone] • www.guidecraft.com
G97300, G97301
Roll Top Desk
Assembly Instructions
Page 4 of 5
P
Place cam pins (C) into holes shown below. Firmly tighten both cam pins.
C
P
R
M O
P
A
A A
A
D
D
D
D
D
D
C C
C
C
Attach roll top sides (M and O) to desk
top (P), using cam pins (C) and cams
nuts (D).
Place cam nuts (D) into holes on side (P) .
Attach desk top (P) to drawer unit (R), then
tighten cam nuts by turning until they’ve
locked into place. Attach sides of desk top to
lower frame using screw (A).
4
4
5
6

Guidecraft • 55509 Highway 19 West, Winthrop, MN 55396 • [phone] • www.guidecraft.com
G97300, G97301
Roll Top Desk
Assembly Instructions
Page 5 of 5
O
M
V
V
B B
Attach top (K) to roll top sides (parts M
and O) using screw (B).
From the back of the unit, insert roll top slats
(L) into grooves in the roll top sides. Make
sure handle cutout (indentation) on the
front-most slat ends up on the front of the
desk.
M O
K
B B
L
E
E
E
E
Insert storage compartment (V) from back of
unit. Ensure the brackets on the sides of the
storage compartment unit slip into the grooves
on the roll top sides (M and O). Attach using
screws (B).
5
7
8
9

Insert desk drawer (Y) from the front of the unit.
Attach back panels W and S using screws (E).
When completed, insert the pull-out tray (Z) in
the front section and the small drawer (G) in
the storage compartment.
Insert the pull-out tray (Z) in the front section
and the small drawer (G) in the storage
compartment.
Roll Top Slat
If at any time the pull-down slats of the roll top desk
stick in the grooves, or become hard to open and
close, rub a small amount of hand soap (Ivory soap
or similar) in the channels. Soap will not damage
the wood and will ensure a smooth opening and
closing of the roll top slats.
W
S
E E E E
E E E E
E E E E
E E E E
E E
Z
G
G
Y
6
10
11
12

G97300, G97301, G97302
7

A
A
B
A(8)
2"
(50mm)
A
A
A
A
A
C
D
Don’t forget to
install Part H, the
center brace.
A
E
E
F
G
G
H
8
12
D
E
E
F
C
H