Great Little Trading Fleming L3818 User manual

1
Fleming Desk
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools. Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the
tools you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
L3818
28/11/2016
V2
easy - medium - hard
Assembly Difculty
one-person job
Thank you for shopping with GLTC, we hope you enjoy having
this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through
the whole process. But if it all feels a bit too much like hard work, then
we do have an assembly company we can recommend: the Flatpack
Construction Company offers a nationwide service and can be
contacted on 0843 289 4951 or www.atpackconstruction.co.uk.

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Check all xtures and ttings regularly and tighten as necessary.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• The painted/lacquered surface is resistant to staining if cleaned
immediately, however please protect the surface from contact with
ball point pen and indelible style felt markers as the ink is by nature
permanent.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
Component Check List
M N
2x Panel N1x Panel M
O P
Q R
S T
U
1x Panel P1x Panel O
2x Panel R1x Panel Q
2x Panel T4x Panel S
2x Panel U
A B
1x Leg B2x Leg A
C D
E F
G H
I J
2x Panel D1x Leg C
1x Panel F1x Panel E
1x Panel H1x Panel G
1x Panel J1x Panel I
K L
1x Panel L1x Panel K

4
Component Check List
#1 #2
20x Cam Locks
14mm Diameter
20x Cam Dowels
35mmL
#3 #4
#5 #6
#7 #8
#9 #10
2x Drawer Stop26x Wooden Dowels
20mmL
16x Screws
20mmL
14x Screws
10mmL
4x Barrel Nuts11x Screws
25mmL
1x Allen Key
8x Threaded Bolt
42mmL
Philips Head Screwdriver
You will need (not supplied)
2x Hinges

5
4x #3 Wooden Dowels
STEP 1:
Prepare the desk legs.
Hardware for Step 2:
4x #2 Cam Locks
#1
#1#1 #1 #1
AB
Hardware for Step 1:
6x #1 Cam Dowels
A C
STEP 2:
Create each pair of legs by connecting them with panel D, as shown. Turn all cam
locks (#2) clockwise to secure.
Note the positioning of both legs labeled A. Ensure the remaining cam dowels are
facing towards each other as shown.
A
A
B
C
D
D
#2
#2 #2
#2
#3
#3
#3
#3

6
STEP 3:
Connect both pairs of legs using panel E. Turn both cam locks (#2) clockwise to
secure.
Ensure all hardware is facing inwards as shown.
STEP 4:
Attaching the legs to the desk storage.
Begin with inserting the 4 x threaded bolts (#9) directly into the 4 legs. Fully tighten
these bolts using the Allen key provided. It is important that they are tightened fully.
The remaining four bolts (#9) need corresponding barrel nuts (#8) to hold them in
place. Again, it is important that they are tightened fully.
Please note, panel F must be positioned with the larger drill holes facing away from
the legs. The hardware (#9) must insert into the larger holes and must be tightened
fully so that each bolt head is recessed into the panel as they will not be accessible
after this step.
This step can also be completed with the legs set upright on the oor and panel F
placed on top of them.
E
2x #3 Wooden Dowels
Hardware for Step 3:
2x #2 Cam Locks
Hardware for Step 4:
4x #8 Barrel Nuts
8x #9 Bolts
#2
#2
#3
#3
#9
#9
#9
#9
#9
#9
#9
#9
#8
#8
#8
#8
F
NOTE:
Please be aware that when assembling the legs to
panels D and E you may notice that the legs remain
loose after the cam locks have been tightened.These
will be secured during the next step.

7
STEP 5:
With the base of the desk on its feet. Insert hardware #1 and #3 as shown.
Please ensure the hardware is positioned as illustration. Not all holes will be used
here, they will be used on a later step.
STEP 6:
Prepare the sides of the desk storage by inserting 1x cam dowels (#1) into each of the
panels as shown.
#1
F
#3
#3
#3
#3
#3
#3
#3
#3
#1
#1
#1 #1
#1
8x #3 Wooden Dowels
Hardware for Step 5:
6x #1 Cam Dowels Hardware for Step 6:
2x #1 Cam Dowels
#1
#1
#1
H
G

8
STEP 7:
Begin to construct the desk storage. Add 3x wooden dowels (#3) to Panel H as
shown before attaching the other panels. Lock panel I into place with cam lock #2.
Slide in panel K when panels I and J are in place.
H
K
H
I
J
3x #3 Wooden Dowels
Hardware for Step 7:
1x #2 Cam Locks
#3
#3 #3
#2
STEP 8:
Connect panel G to the other side of the panels as
shown with 3 x wooden dowels (#3) and lock into
place with cam lock #2.
3x #3 Wooden Dowels
Hardware for Step 8:
1x #2 Cam Locks
#3
#3 #3
#2
G
H
I
STEP 9:
Take panel L and insert 6x cam dowels (#1) as shown. Also attach the 2x drawer
stops (#4)using screw #5.
2x #4 Drawer Stop
Hardware for Step 9:
6x #1 Cam Dowels
2x #5 Screws
#1
#1
#1
#1
#1
#1
#5
#5
#4
#4
L

9
STEP 10:
Connect panel L with the divider panel M and the part constructed desk storage.
First insert 6x wooden dowels (#3) into panel L as shown.
Then place the central divider panel M over the dowels and secure in place by
inserting and turning the two cam locks (#2).
Then take the part constructed desk storage and place on the top of panel L, again
securing by inserting and turning the four remaining cam locks (#2) on the side panels.
STEP 11:
Insert the storage dividers.
Hardware for Step 12:
8x #7 Screws
N
6x #3 Wooden Dowels
Hardware for Step 10:
6x #2 Cam Locks
#3
#3
#3
#3
#3
#3
#2
#2
#2
#2
#2
#2
M
G
L
N
STEP 12:
Secure the storage dividers in place.
Ensure the dividers are straight and in the correct position before inserting the
screws.
#7
#7
#7
#7
#7
#7
#7
#7

10
STEP 13:
Turn the desk storage over and place on top of the legs. Ensure all the hardware in
the leg section is inserted into the corresponding holes in the storage section.
Begin securing the two sections by inserting 3 x Hardware #7 in the holes shown.
STEP 14:
Complete the xing of the desk top to the legs by inserting and securing 6x cam locks
(#2).
Remember to secure the 3 cam locks at the very back of the drawer section that has
been created.
Hardware for Step 14:
6x #2 Cam Locks
#7
L
#2
#7
#7
Hardware for Step 13:
3x #7 Screws
#2
#2 #2
#2
#2