Haier HLP0001AXW User manual

Dryer Stack Stand Kit
For use with compact models:
HLP141E Dryer, HLP28E Washer, HLP21 Washer
FR)Dryer Stack Stand Kit
FR)For use with compact models:
HLP141E Dryer, HLP28E Washer, HLP21 Washer
SP)Dryer Stack Stand Kit
SP)For use with compact models:
HLP141E Dryer, HLP28E Washer, HLP21 Washer
Installation Instructions
FR)Installation Instructions
SP)Installation Instructions
HLP0001AXW

1
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .................................................................2
General Safety Precautions .......................................................................................... 2
PARTS AND FEATURES .......................................................................................3
INSTALLATION INSTRUCTIONS..........................................................................4
Tools Needed ................................................................................................................. 4
Location Requirements................................................................................................. 4
STEP BY STEP INSTRUCTIONS............................................................................5
Assemble Stand ............................................................................................................. 5
Attach Dryer .................................................................................................................. 7
Attach Stand to Wall ...................................................................................................... 8
Thank you for purchasing this Haier®product. The installation instructions will
help you get the best performance from your products.

2
IMPORTANT SAFETY INSTRUCTIONS
•Read all of the instructions before using this product.
•Use this product only for its intended purpose as described in the
installation instructions.
WARNING
Installation of this stand to dryers other than Haier®approved models
may result in death or severe injury.
GENERAL SAFETY PRECAUTIONS
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so could result in death or serious injury.
•This product must be properly installed and located in accordance with
the installation instructions before it is used.
•Do not install this product where it will be exposed to temperatures
below freezing or exposed to weather, which can cause damage to the
product.
•Keep the area around your appliance free from combustible materials
such as lint, paper, rags and chemicals.
•Close supervision is necessary if this appliance is used by or near
children. Do not allow children to play on, with, or inside this appliance.
•Properly dispose/recycle all packing material.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY

3
PARTS AND FEATURES
Mounting Brackets
Support Brace
Double-Sided Foam Tape
Cross Braces
Carriage Bolt
Lag Bolt
#8 Phillips-head Screws (2)
Lock Nut
Flat Washer
Split Lock Washer
Star Washers (2)

4
INSTALLATION INSTRUCTIONS
TOOLS NEEDED
•7/16" Wrench •Phillips screwdriver
LOCATION REQUIREMENTS
• The stand must be installed on a solid oor. A concrete oor is best.
• The oor should be level.
•A suitable location is protected from direct sunlight and heat sources such as
radiators, baseboard heaters, or cooking appliances.
•Do not install on carpeting.
•The location must have appropriate electrical and gas supply outlets. See the
“Electrical & Gas Supply Requirements” section in your product’s User Manual.
•Do not install in a location where the dryer might come into contact with
combustible materials such as, but not limited to curtains, thick carpet, and/or
any materials that might obstruct ventilation.
STAND DIMENSIONS
75"
(190.5 cm)
49"
(124.5 cm)
24½"
(62.2 cm)
22"
(55.9 cm)

5
STEP BY STEP INSTRUCTIONS
ASSEMBLE STAND
1. Setup stand with mounting brackets on top.
Mounting Brackets
WARNING
Pinch Hazard
Cross braces will slide and create pinch points during set-up. Keep
hands clear of sliding cross braces and their connection points.
Do not insert finger into moving parts. Doing so may result in severe
injury, cut or pinch.
2. Grasp the left and right side as shown. Pull apart. Make sure the bolts have slid all
the way to the bottom of the slot to ensure the stand is completely open.

6
3. Using the carriage bolt, washer and lock nut attach the support brace with a
7/16"wrench. Completely tighten both sides of the support brace.
Support Brace
Carriage Bolt
Lock Nut
Flat Washer
4. Completely tighten all 7 cross-brace nuts with a 7/16"wrench.
Cross Braces

7
ATTACH DRYER
1. Remove bottom 2 panel screws from the back of the dryer and discard.
Panel Screws
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in death or personal injury.
2. Lift dryer onto the stand and position the dryer so the screw holes align with the
mounting bracket holes.

8
3. Using the #8 Phillips-head screws and star washers provided, fasten the dryer to
the mounting brackets.
#8 Phillips-head Screw
Star Washer
ATTACH STAND TO WALL
1. Remove the paper liner from the double-sided foam tape on the back of the
support brace.
Support Brace
Double-Sided Foam
Tape
WARNING
Tip and Utility Rupture Hazard
Stand must be securely assembled, fastened to wall and dryer attached
to stand, per installation instructions.
Failure to do so could result in death, personal injury or property
damage.
2. Carefully walk the stand and dryer assembly into the nal location.

9
3. Firmly apply pressure to the length of the support brace to adhere the double-
sided foam tape to the wall.
Support Brace
4. Locate a stud in the wall. Using the lag bolt and split lock washer, secure the
support brace to the wall.
Stud
Support Brace
Lag Bolt
Split Lock Washer