Hallmark TG76M3X04S00 User manual

ITEM #0672387
7.5 FT FROSTED HAVEN FIR
MODEL #TG76M3X04S00
Español p. 7
1
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-919-0070, 8 a.m. - 5 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date

2
1
1
1
PACKAGE CONTENTS
DESCRIPTIONPART QUANTITY
1
Tree Top
1
2 Tree Middle
Tree Bottom
1
3
4Tree Stand
5
6
Cord (preassembled)
Foot Pedal (preassembled)
1
3
2
1
4
5
6

3
CAUTION
RISK OF FIRE
Do not replace attachment plug. It contains a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
To reduce the risk of overheating, replace burned-out lamps promptly. Use 2.5-volt lamps only.
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
insulation.
products that may be attached to the product. Replace the fuse as per the user servicing instructions
a short-circuit may be present and the product should be discarded.
SAVE THESE INSTRUCTIONS.
PREPARATION
contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 5 minutes.
No Tools Required for Assembly.
SAFETY INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the
product.

4
3. Remove protective cap from tree middle (2). Insert tree
middle (2) into tree bottom (1).
4. Insert tree top (3) into the top hole of the tree middle (2).
ASSEMBLY INSTRUCTIONS
2. Remove protective cap from tree bottom (1). Insert tree
bottom (1) into tree stand (4).
2
1
3
4
5
4
1
1
2
2
3
6
5
4
4
6
5
6
Click
1. Open tree stand (4) by pulling apart the legs of the tree stand
(4) until they snap into an X-shape. Place tree stand (4) on a
level surface.
NOTE: To close tree stand (4), push the button in middle and
fold the legs back together.
4

5
• Before using or reusing, inspect product carefully. Discard any products that have cut, damaged or
branches, or bushes, to avoid any undue strain or stress on the product conductors, connections
• When not in use, store neatly in a cool, dry location protected from sunlight.
CARE AND MAINTENANCE
Grip plastic
not glass
Pull straight out
Remove lamp base Replace lamp base
Burned fuse
•
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
out of lamp holder.
FUSE REPLACEMENT INSTRUCTIONS:
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
2. Open fuse cover by sliding open the fuse access cover on top of
attachment
3. Remove fuse carefully: turn fuse holder over, remove fuse.
5. Close fuse cover by sliding closed the fuse access cover on top of
attachment plug.
BULB REPLACEMENT INSTRUCTIONS:
5. Shape and shift tree branches to fill in any gaps.
Insert the red-label plugs into red-label extension cord
and insert the plug of the green label extension cord
(5) into a wall outlet.
5
2
1
3
65
4
Customize your tree by adding Christmas cards, family
photos or other special decor onto the display branches.

6
REPLACEMENT PARTS LIST
Fuse Bulb
B
A
For replacement parts, call our customer service department at 1-888-919-0070, 8 a.m. - 5 p.m., EST,
Monday - Friday.
A
B
Fuse
Bulb
CFuse Lamp
T NPAR DESCRIPTIO
Fuse Lamp
C
TROUBLESHOOTING
Bulb broke.
1. Start with the first unlit bulb, then gently push (don't twist)
each bulb firmly into the socket.
2. Look and feel for a broken bulb in the socket or an
empty socket where a bulb has fallen out.
Mark the bulb with a piece of tape and unplug the tree
before removing the bulb socket and any fragments.
Replace the broken bulb.
Replace any burned out bulbs.
One bulb will not light.
A section will
not light.
Bulb is broken.
1. Bulb is loose.
2. Bulb broke or
fell out.
Bulb burned out.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
1. Grasp the plug and remove from the receptacle or other outlet device. Do not
unplug by pulling the cord.
2. Locate the fused lamp with gray color lamp holder. Pull the burnt fused lamp
and plastic lamp base straight out of the lamp holder.
3. Replace with a spare fused lamp. The fused lamp can be distinguished by a
gray lamp base and an additional clear plastic cover.
4. Plug in the lights again.
FUSED LAMP REPLACEMENT
WARNING - Risk of fire: This product employs overload protection (fuse lamp) in
each series light circuit to provide overload protection in addition to the fuse(s)
located in the plug. Do not replace the fuse lamp contained in this set with any
other type of lamp, use only spare fuse lamps provided with this product. In case
of a burnt out FUSED lamp, the entire series of 50 lamps will be out. To replace
the fused lamp: