Hanasis HW-3000 Guide
HW-3000
e-Manual
※ Please read and learn the manual carefully for your safety and proper way of use.
Safety precautions
HW-3000 preview
Specification & options
Locations
ㆍParts description
ㆍI/O port
ㆍRating label zone
Contents
System Introduction
Remove the protective tape
Adjusting Viewing Angle
Connecting DC Power
Supply Cable & System on
System Installation
BIOS Setup
BIOS
Touch Screen
MSR
Kitchen Printer
Using the product
Winclon (Backup)
Winclon (Restore)
POS Driver & Utility
System Block Diagram
MotherBoard Layout
Setting Jumper
Appendix
I/O Pin Assignment
MSR
STAND
HDD
Assembly & Disassembly
REAR COVER
EMI
WALL MOUNT
9.7” DUAL(TOUCH) MONITOR
ㆍInstallation / Connect cable
ㆍSystem Setup
15” DUAL(TOUCH) MONITOR
ㆍInstallation / Connect cable
ㆍSystem Setup
NFC
ㆍInstallation / Connect cable
ㆍBIOS Setup
BARCODE SCANNER
ㆍInstallation / Connect cable
ㆍReset Default Setup
ㆍCOM 1, COM 2/ 3
ㆍCOM 4, VGA
ㆍUSB, DC-IN, DC-OUT
ㆍPS/2 MOUSE, PS/2 KBD
ㆍLAN, MSR
Contents
Assembly &
Disassembly
BIOS
Appendix
Using the product
Safety precautions
Do not block the ports(holes), Vents, etc, of the system and do not insert objects.
Damage to a component within the system may cause electric shock or fire.
Do not touch the system plug or power cord with wet hands. There is a danger of electric shock.
Do not exceed the standard capacity(Voltage/current) of a multiplug or power outlet extension when using it for the product.
There is a danger of electric shock or fire hazard.
Do not unplug the power cord by pulling the cable only. If the cord is damaged, it may cause electric shock.
Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.
Otherwise, there is a danger of fire due to an incomplete contact.
Do not use the system in a humid location such as a bathroom or sauna.
Please use the system within the recommended temperature and humidity range(10~32˚C, 20~80% RH).
Avoid direct sunlight when the system is in an air-tight location such as inside a vehicle.
There is a danger of a fire hazard. The system may overheat and also present opportunity to thieves.
System Installation
System Introduction
Safety precautions
HW-3000 preview
Specification & options
Locations
For your security and to prevent damage, please read the following safety instructions carefully.
Failing to follow instructions marked with this symbol may cause personal injury and even fatality.
Contents
Assembly &
Disassembly
BIOS
Appendix
Using the product
System Installation
System Introduction
Safety precautions
HW-3000 preview
Specification & options
Locations
Thank you for purchasing Hanasis's POS.
(Product specifications may differ according to region and may be changed without prior notice)
■ System preview
HW-3000 preview
Class-A digital device
A digital device that is marketed for use in a commercial, industrial or business environment,
exclusive of a device which is marketed for use by the general public or is intended to be used in the home.
This product is developed and tested on the basis of our reliability and outstanding technology.
This product has applied exclusive and emotional design and also provides wide expandability such as barcode scanner or NFC.
This product has applied low power atom platform design, 15” Window(TFT) touch screen and 9.7” dual monitor expandability.
This will allow users to save maintainance cost and will provide comfortable user experience.
This product is designed for users to fix easily by using hand screws in system main body and stand, and also by decreasing the number of screws.
This product has acquired domestic and international standard, applied a technology patent that is created by Hanasis.
registered trademark
The symbol mark is the foundation element that symbolizes the Hanasis corporation and it is also a symbol of communication at both home and abroad.
The basic concept is a leading IT industry. It embodies Hanasis's corporate goal to link world faster by using advanced IT technology.
The symbol mark express Hanasis's industry representative. The symbol expresses the image of network envrionment and advanced technology in dynamic way.
Contents
Assembly &
Disassembly
BIOS
Appendix
Using the product
System Installation
System Introduction
Safety precautions
HW-3000 preview
Specification & options
Locations
(Product specifications may differ according to region and may be changed without prior notice.)
◆ Specification ◆ Options
Specification & options
OS
Wall Mount
Touch Panel
Dual Display
iButton
MSR
Barcode Scanner
Color Product
Smart IC Card
Microsoft
®
Windows7, POSReady7 / 2009, windows XP
Fixed Type , Swivel Type
(75x75, 100x100mm VESA)
15", 5-Wire Resistive (Bezel type / Bezelless type)
9.7”, TFT-LCD, 1024x768, LED panel (Touch)
15”, TFT-LCD, 1024x768, LED panel
Probe(USB), Dallas key
ISO Track2 , Track 1&2 , Track 1&2&3
USB Module(Internal) type, 1D, 2D
IC Card Reader(USB), EMV Level#1
White Black
Processor(CPU)
Chipset
Memory
HDD
Display
VGA / DVI
HDMI
LAN
Serial(RS-232C)
Parallel(LPT)
PS/2
USB
Audio
Speaker
Expansion Interface
Cooler & FAN
Power Adaptor
Dimension(mm)
Weight
Intel
®
Intel
®
Celeron® 1037U Dual-Core (1.8GHz, 2M Cash)
NM70
2GB DDR3 1333MHz, SoDIMM (Up to 8GB)
2.5”, SATA-III 320GB~ or SSD 32GB~
m-SATA (32GB~)
15", 1024 X 768, 24Bit
Luminance : 250 cd/㎡, Backlight : LED
1EA VGA (DSUB15) Intel® HD Graphics 2500
-
2 EA (Intel® Gigabit LAN)
4 EA (DSUB-9p x 3EA / RJ-45 x 1EA)
-
2 EA (Keyboard / Mouse)
4 EA (I/O) (USB2.0)
2 EA (Front) (USB2.0)
2 EA (Line-Out / MIC-In) Realtek ALC269 HD2.1 Audio
1 EA (1W)
1 EA PCIe Socket
1 EA Full Size Mini PCIe Socket (m-SATA)
Fanless
60[W] Adaptor
Input AC 100~240V/50~60HZ, DC 12V/5A
364(W) x 332(H) x 200(D) (Normal Angle, With Stand)
7.3kg
NFC
Serial Module(Interal) type, SSCPRO NFM1V0
Contents
Assembly &
Disassembly
BIOS
Appendix
Using the product
System Installation
System Introduction
Safety precautions
HW-3000 preview
Specification & options
Locations
ㆍParts description
ㆍI/O port
ㆍRating label zone
Parts description
(Product specifications may differ according to region and may be changed without prior notice.)
Power supply lamp
Error lamp
Reset button
Card reader(MSR)
Exteral USB(2port)
HDD lamp
LAN lamp
Dual(touch) monitor
Cover cable
NFC reader(Option)
Barcode scanner(Option)
Camera(Option)
Cable vent
Cable space
(9.7” / 15”)
Power button & Power supply lamp
1. Card reader (MSR) : Device that recognizes credit cards.
※ power supply lamp : green light / error lamp : red light / reset button : Use when initializing the Card reader.
2. HDD lamp : The light will be turned on when the hard disk is reading or writting data.
3. LAN lamp : The light will be turned on when connected to the internet.
4. Power supply lamp : The light will be turned on when the system is on.
5. 9.7” / 15” Dual(touch) monitor : Option
6. Barcode scanner / NFC reader : Option
7. Cover cable : Disassemble the cover and then you can connect the I/O port.
8. Cable space / vent : Disassemble the cover and then you can reorganize the cables that are connected.
Contents
Assembly &
Disassembly
BIOS
Appendix
Using the product
System Installation
System Introduction
Safety precautions
HW-3000 preview
Specification & options
Locations
ㆍParts description
ㆍI/O port
ㆍRating label zone
I/O port
1. PS/2 (MOUSE)
2. PS/2 (KBD)
3. D-SUB 9PIN serial(COM)
4. D-SUB 15PIN VGA
5. RJ-45 LAN
6. USB 2.0
7. AUDIO port (LINE-OUT)
8. MIC port (MIC-IN)
9. DIN 4PIN 12V DC-IN
10. 12V DC-OUT
11. RJ-45 8PIN COM
12. RJ-45 8PIN MSR86%W\SH
13. HDD
PS/2 type of mouse
PS/2 type of keyboard
Equiments that use serial port such a barcode scanner and printer
Dual(touch) monitor
Internet connection
USB keyboard, USB mouse, NFC reader etc.
External speakers
External mic
Adaptor jack that provides system power
Dual(touch) monitor power jack
Equiments that use serial port
0DJQHWLF6WULSH5HDGHU
SSD or 2.5” HDD
(standard)
OUT(12V)
COM4 MSR(USB)
IN(12V)
POWER
HDD Tray
LAN
COM1
COM2 COM3
USB
VGA
LINE-OUT
MIC-IN
MOUSE
KBD USB
LAN
13 3 57
2346
121110
13
89
Contents
Assembly &
Disassembly
BIOS
Appendix
Using the product
System Installation
System Introduction
Safety precautions
HW-3000 preview
Specification & options
Locations
ㆍParts description
ㆍI/O port
ㆍRating label zone
Rating label zone
Before you setup the product(HW-3000).
Remove the protective tape before setup.
Contents
Using the product
Assembly &
Disassembly
BIOS
System Introduction
Appendix
Connecting DC Power
Supply Cable & System on
Remove the protective tape
Adjusting Viewing Angle
Remove the Protective Tape
Protective Tape
System Installation
Contents
Assembly &
Disassembly
BIOS
System Introduction
Appendix
Connecting DC Power
Supply Cable & System on
Remove the protective tape
Adjusting Viewing Angle
System Installation
5˚
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.
You are able to adjust the monitor's angle from 5°to 50°.
Adjusting Viewing Angle
50˚
Using the product
Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.
Otherwise, there is a danger of fire due to an incomplete contact. Do not touch the system plug or power cord with wet hands
Contents
Assembly &
Disassembly
BIOS
System Introduction
Appendix
Remove the protective tape
Adjusting Viewing Angle
System Installation
1
cover cable
stand
side cover
grab
stand
side cover
1
OUT(12V)IN(12V)
POWER
① Separate the Cover Rear Stand, as shown in drawing.
② Separate the Cover Cable.
③ Connect the Adaptor Cable.
④ Press Power button to turn the system on.
3
3
Connecting DC Power Supply Cable & System on
Please always check the directions.
Connecting DC Power
Supply Cable & System on
Using the product
Contents
System Installation
Assembly &
Disassembly
BIOS
System Introduction
Appendix
MSR
Winclon (Backup)
Kitchen Printer
Winclon (Restore)
POS Driver & Utility
Touch Screen
Do not apply a severe impact to the touch screen or press the screen with a sharp object such as a ball-point pen.
This may damage the touch screen.
■ Touch Point Setup
Touch Screen
When you use the touch screen for the first time or the pointer does not precisely match your touch, calibrate the touch screen
in the ‘eGalaxTouch’. The calibration process for the touch screen may differ depending on the operating system and may not be available in
some operating systems. The following descriptions assume the Windows POSReady2009 operating system.
① Click Start→All Programs→eGalaxTouch→Configure Utility
② Click the 'Tools' tab and ‘4Points Calibration’
③ When the Calibration window appears, touch the point represented by the “+”.
④ The “+” is displayed from the bottom left to the top left of the screen sequentially.
⑤ The touch screen input points are calibrated.
Using the product
Contents
System Installation
Assembly &
Disassembly
BIOS
System Introduction
Appendix
MSR
Winclon (Backup)
Kitchen Printer
Winclon (Restore)
POS Driver & Utility
Touch Screen
Using the product
Learn the proper way of using card reader before using the product.
When the card is inappropriately recognized, the red ligth will be turned on with the beep sound.
① grab your credit card as the picture shows.
※ make sure the magnetic side of the card towards out side.
② Push your credit card in the direction of the arrow.
③ Slide down your credit card gently in the direction of the arrow.
■ Proper way of using the card reader
MSR
1
2
3
Contents
System Installation
Assembly &
Disassembly
BIOS
System Introduction
Appendix
MSR
Winclon (Backup)
Kitchen Printer
Winclon (Restore)
POS Driver & Utility
Touch Screen
Using the product
In order to connect POS device with kitchen printer, please regard to the following connection drawing.
You must use the interchangable gender that is provided by Hanasis.
■ cable connection specification for kitchen printer serial cable
Kitchen Printer
[SRP-350] [SRP-330] [TM-T83] [SRP-350] [TM-T83]
1: N.C
2: DSR
3: TXD
4: RXD
5: RTS
6: CTS
7.GND
8: DTR
POS(COM4)
1: N.C
2: DSR
3: TXD
4: RXD
5: RTS
6: CTS
7.GND
8: DTR
interchangable gender
(RJ45-DB25)
1
8
8
1
interchangable gender
Extension Cable
Extension cable insert
※ The interchangable gender will only be enclosed with
the kitchen bell when you order a Kitchen printer.
Connect the printer
Contents
System Installation
Assembly &
Disassembly
BIOS
System Introduction
Appendix
MSR
Winclon (Backup)
Kitchen Printer
Winclon (Restore)
POS Driver & Utility
Touch Screen
Using the product You need to connect key board before you turn the power on.
Back up your current Window user environment into restore field.
It is much easier to operate if you know where the data is being backed up.
■ HDD Backup
Winclon (Backup)
① Connect the keyboard and mouse to the system.
After turning on the system, follow the on-screen instructions:
press <F11> when the “F11 to WinClon ...” message appears on the screen within 2 to 4 seconds (PC POST process).
② When WinClon appears on the screen, press <F10> key on your keyboard or click the mouse to select “Backup”.
③ After entering the password, press the <OK> button to continue the backup. (Password: pos)
pos
Backup file location
(The programs may vary depending on different model.)
■ HDD Backup (The programs may vary depending on different model.)
Contents
System Installation
Assembly &
Disassembly
BIOS
System Introduction
Appendix
MSR
Winclon (Backup)
Kitchen Printer
Winclon (Restore)
POS Driver & Utility
Touch Screen
Using the product If you recover the Hard disk, all the data of the system will be deleted.
Please save all the important data in the external storage before you start recovering.
You can recover quickly despite when you are not able to boot from the OS or when having any problems.
Keyboard and mouse must be connected.
Winclon (Restore)
① Connect the keyboard and mouse to the system.
After turning on the system, follow the on-screen instructions:
press <F11> when the “F11 to WinClon ...” message appears on the screen within 2 to 4 seconds (PC POST process).
② When WinClon appears on the screen, press <F2> key or <F3> on your keyboard or
click the mouse to select “Recover recent state” or “Recover initial state”.
③ After entering the password, press the <OK> button to continue the restore. (Password: pos)
※ Recover recent state” is restored to the most recent backup of Windows.
※ Recover initial state” is restored to the factory default state.
pos
Contents
System Installation
Assembly &
Disassembly
BIOS
System Introduction
Appendix
MSR
Winclon (Backup)
Kitchen Printer
Winclon (Restore)
POS Driver & Utility
Touch Screen
Using the product
All the drivers and data that are provided with your purchase are in the D drive of Hard disk.
POS Driver and Utility
▶It is the contents from the D:\Utility.
There are install files in each folders.
Drivers
Utility
Manual
MSR
HDD AlignTool
AdobeReader
Contents
System Installation
System Introduction
BIOS
Appendix
Using the product
■ MSR separation
MSR
OM4 MSR(USB)
HDD Tray
Cover cable
When reassembling the card reader, you must assemble tightly otherwise the card will not be recognized by the reader.
① Separate the cover cable by pushing it upwards.
② Disconnect MSR connector.
③ Remove 2 hand screws.
④ Separate the MSR by pushing it in the direction of the arrow.
1
2
Screw
3
4
Stand
Rear Cover
HDD
EMI
9.7” Dual monitor
15” Dual monitor
Wall mount
NFC
Barcode Scanner
MSR
Assembly &
Disassembly
The stand is heavy so please be careful with it. When reassembling, for your safety,
you must put the lever in the correct insertion point.
■ Stand separation
Contents
System Installation
System Introduction
BIOS
Appendix
Using the product
Assembly &
Disassembly
① Lift the lever(ⓐ).
② Pull the stand in the direction of the arrow indicated.
③ Lift up and remove the stand.
Lever
Insertion Point
12
3
a
Stand
Stand
Rear Cover
HDD
EMI
9.7” Dual monitor
15” Dual monitor
Wall mount
NFC
Barcode Scanner
MSR
Contents
System Installation
System Introduction
BIOS
Appendix
Using the product
Assembly &
Disassembly
Care must be taken when removing the HDD and bracket to avoid injury.
Save all your data before clicking on Shut down. Disconnect the Adaptor cable from the system.
① Separate the Cover Cable.
② Rotate(Counter Clockwise) the Hand screw.
③ Pull the HDD out of the system.
④ Separate the HDD from the Bracket HDD.
⑤ Replace the new HDD into the Bracket HDD and assemble in reverse order.
■ Hard Disk Drive Replacement
HDD
1
Cover cable
2
3
4
4
Stand
Rear Cover
HDD
EMI
9.7” Dual monitor
15” Dual monitor
Wall mount
NFC
Barcode Scanner
MSR
Table of contents
