Hanasis HW-9000 User manual
USER GUIDE
※ Product specifications are subject to change without prior notice and may vary according to region.
● Hanasis shall not be liable for technical or editorial errors in this document.
● This user guide is not intended for everyone. It is written for technically qualified personnel only.
1
Datachment
Handle
Stand
Side Cover
Stand
Side Cover
1
I/O Ports Cover
Please always check
the directions.
① Detach the Stand Side Covers as shown in the illustration.
② Detach the I/O Ports Cover.
③ Connect the Power Adapter.
④ Press the Power Button to turn on the system.
■ Connecting DC Power Supply Cable & Turning System On
3
3
[ Standard ]
□ I/O Ports Layout
■ Parts Description
Power Lamp
(MSR, SCR, iButton)
Error Lamp
Reset Button
Card Reader
External USB (2 ports)
Storage Lamp
Lan Lamp
Power Button &
Power Supply Lamp
Dual (Touch) Monitor
I/O Ports
NFC Reader
Barcode Scanner
(Optional)
(Optional)
Cable Vent
Cable Space
Power Button
Power
Adaptor
Learn the proper way to use the card reader before using the product.
If a card is inappropriately recognized, the red light will blink with a sound indicating error.
■ Proper Way to Use Card Reader
1
2
3
① Hold up your credit card as shown in the illustration.
※ Face the magnetic side of the card outwards.
② Place your credit card inside the slot of the card reader.
③ Slide down your credit card gently in the direction of the arrow.
① Click Start→All Programs→eGalaxTouch→Configure Utility
② Click the 'Tools' tab, then ‘4 Points Calibration’
③ The touch screen input points are calibrated.
■ Touch Screen Calibration
When using the touch screen for the first time or if the pointer does not precisely match your touch, calibrate the touch screen
using the ‘eGalaxTouch’ tool. Depending on the operating system, the calibration process may vary and may not be available in
some operating systems.
Do not apply severe impact to the touch screen. Avoid sharp objects such as ball-point pen when pressing the screen.
This may damage your touch screen.
F11 to Recovery Zone....
■ Recovery Solution (Optional)
F11 to Recovery Zone....
1. Turn on the system and follow the on-screen instructions: Press <F11> when the “F11 to WinClon ...” message
appears on the screen within 2 to 4 seconds (PC POST process).
2. When WinClon appears on the screen, press <F2> or <F3> key on your keyboard or use your mouse to select
“Recover to Recent State” or “Recover to Initial State”.
3. After entering the password, press the <OK> button to continue restore. (Password: pos)
※ "Recover to Recent State” will restore to the most recent backup of Windows.
※ "Recover to Initial State” will restore to the factory default settings.
● Restore
When you recover the Hard Disk, all the data in the system will be deleted.
Please save all important data in external storage before you start recovery.
You can still recover quickly even if you are not able to boot from the OS.
Keyboard and mouse must be connected.
pos
Password
OK
① Turn on the system and follow the on-screen instructions:
Press <F11> when the “F11 to WinClon ...”
message appears on the screen within 2 to 4 seconds
(PC POST process).
② When WinClon appears on the screen, press <F10> key on your
keyboard or use your mouse to select “Backup”.
③ After entering the password, press the <OK> button to continue backup. (Password: pos) Location of backup image
● Backup
Back up your current Window user environment into restore field.
It is much easier to operate if you know where the data is
being backed up.
Keyboard and mouse must be connected
(Recovery program may vary depending on model))
pos
Password
OK
I/O Ports Cover
1
Save all your data before clicking on shut down. Disconnect the power supply from the system.
To avoid injury, care must be taken when removing the HDD tray.
■ Storage(HDD/SSD) Replacement
① Detach the I/O Ports Cover.
② Rotate the hand screw counterclockwise
③ Pull the HDD tray out from the system.
④ Separate the HDD from the bracket.
⑤ Replace with new HDD into bracket.
and assemble in reverse order.
2
2
3
4
4
a
① Lift the Lever (ⓐ).
② Pull the stand in the direction
of the arrow indicated.
③ Lift up and remove the stand.
The stand is heavy so please be careful.
For your safety, you must put the lever in the correct insertion point when reassembling.
■ Stand Separation
Lever
Insertion Point
12
3
I/O Ports Cover
When reassembling the card reader, you must assemble tightly otherwise the card will not be recognized by the reader.
① Detach the I/O Ports Cover by pushing it upwards.
② Disconnect MSR connector.
③ Remove both screws.
④ Separate the MSR by pushing it in the direction of the arrow.
■ Card Reader (MSR, SCR, iButton) Separation
1
2
3
4
HM1M-00007C
