Hanwha Vision SHB-V-3200HPR User manual

EN
English - Instruction manual
SHB-V-3200HPR
Outdoor Enclosure Kit for Box Cameras
Installation Manual

overview
A_Overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package. Each item may be package in its' own box.
This document may refer to each component using the item names listed below.
Appearance Item Name Quantity
HOV32K2A700
OUTDOOR HOUSING
WITH POE/HPOE
1
WBJA
WALL BRACKET
WITH BALL JOINT
1
GEKO IRH30L
IR ILLUMINATOR
1
OSUPPIR
BRACKET FOR IR ILLUMINATOR
1
Appearance Item Name Quantity
MOUNT CAP 5
MOUNT CAP fastener 1
M10 x L22 screw (to attach the install bracket) 4
M8 x L20 screw (to attach the housing) 4
M3 x L6 screw
(to attach the bracket adaptor and media convert) 4
M10 x L12 wrench bolt (to attach SBP-300WM/WMW) 4
M10 x L20 wrench bolt (to attach SBP-300WM1/WMW1) 4
M4 x L8 screw (to attach the media convert) 2
Note: A PoE/PoE+ switch or injector is required, not included.

EN - English - Instruction manual
2 MNVCHOVHPOE_2222_EN
Contents
ENGLISH 1
1 About this manual ....................................................................................................................3
1.1 Typographical conventions ................................................................................................................................................ 3
2 Notes on copyright and information on trademarks.............................................................3
3 Safety rules................................................................................................................................3
4 Identification.............................................................................................................................4
4.1 Product description and type designation................................................................................................................... 4
4.2 Product marking..................................................................................................................................................................... 4
5 Preparing the product for use .................................................................................................5
5.1 Unpacking................................................................................................................................................................................. 5
5.2 Contents .................................................................................................................................................................................... 5
5.3 Safely disposing of packaging material ......................................................................................................................... 5
5.4 Preparatory work before installation............................................................................................................................... 5
5.4.1 Mounting the bracket ............................................................................................................................................................................ 5
6 Installation ................................................................................................................................6
6.1 Housing opening.................................................................................................................................................................... 6
6.2 Slide removal ........................................................................................................................................................................... 6
6.3 Installation of cable glands................................................................................................................................................. 6
6.4 Installation of the GEKO IRH illuminator ...................................................................................................................... 6
6.4.2 Ethernet cable installation....................................................................................................................................................................7
6.4.3 How to install the camera..................................................................................................................................................................... 8
6.4.4 Connection of the GEKO IRH illuminator...... ................................................................................................................................... 8
6.4.5 PoE cable connection............................................................................................................................................................................. 9
7 Configuration............................................................................................................................9
8 Switching on ...........................................................................................................................10
9 Maintenance and cleaning.....................................................................................................11
9.1 Maintenance ..........................................................................................................................................................................11
9.1.1 Kit for upgrading of the equipment................................................................................................................................................11
9.2 Cleaning...................................................................................................................................................................................11
9.2.1 Cleaning the window and plastic parts.........................................................................................................................................11
10 Information on disposal and recycling...............................................................................12
11 Technical data .......................................................................................................................12
11.1 General ..................................................................................................................................................................................12
11.2 Mechanical ...........................................................................................................................................................................12
11.3 Electrical................................................................................................................................................................................12
11.4 Environment........................................................................................................................................................................12
11.5 Certifications........................................................................................................................................................................12
12 Technical drawings ...............................................................................................................13

Instruction manual - English - EN
3MNVCHOVHPOE_2222_EN
1 About this manual
Read all the documentation supplied carefully
before installing and using this product. Keep the
manual in a convenient place for future reference.
Note: Some sections of the manual that refer to
options that are not available have been removed.
1.1 Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the
power supply before proceeding with any
operation, unless indicated otherwise.
CAUTION!
Medium level hazard.
This operation is very important for the
system to function properly. Please read
the procedure described very carefully and
carry it out as instructed.
INFO
Description of system specifications.
We recommend reading this part carefully
in order to understand the subsequent
stages.
2 Notes on copyright and
information on trademarks
The mentioned names of products or companies are
trademarks or registered trademarks.
3 Safety rules
CAUTION! Device installation and
maintaining must be performed by
specialist technical staff only.
CAUTION! The electrical system to which
the unit is connected must be equipped
with an automatic bipolar circuit breaker.
The circuit breaker for main supply
voltage phase units must have a level of
intervention of 20A max. The circuit breaker
for low voltage units must have a level of
intervention of 6A max. This circuit breaker
must be of the Listed type. The minimum
distance between the circuit breaker
contacts must be 3mm (0.1in). The circuit
breaker must be provided with protection
against the fault current towards the
ground (differential) and the overcurrent
(magnetothermal).
• The manufacturer declines all responsibility
for any damage caused by an improper use
of the appliances mentioned in this manual.
Furthermore, the manufacturer reserves the right
to modify its contents without any prior notice.
The documentation contained in this manual has
been collected and verified with great care. The
manufacturer, however, cannot take any liability
for its use. The same thing can be said for any
person or company involved in the creation and
production of this manual.
• Before starting any operation, make sure the
power supply is disconnected.
• Be careful not to use cables that seem worn or old.
• Never, under any circumstances, make any
changes or connections that are not shown in
this handbook. Improper use of the appliance
can cause serious hazards, risking the safety of
personnel and of the installation.
• Use only original spare parts. Non-original spare
parts could cause fire, electrical discharge or other
hazards.
• Before proceeding with installation, check the
supplied material to make sure it corresponds
to the order specification by examining the
identification labels (4.2 Product marking, page 4).

EN - English - Instruction manual
4 MNVCHOVHPOE_2222_EN
• This device was designed to be permanently
secured and connected on a building or on a
suitable structure. The device must be permanently
secured and connected before any operation.
• Comply with all the national standards during the
device installation.
• Installation category (also called Overvoltage
Category) specifies the level of mains voltage
surges that the equipment will be subjected to.
The category depends upon the location of the
equipment, and on any surge voltage protection
provided. Equipment in an industrial environment,
directly connected to major feeders/short branch
circuits, is subjected to Installation Category
III. If this is the case, a reduction to Installation
Category II is required. This can be achieved by
use of an insulating transformer with an earthed
screen between primary and secondary windings,
or by fitting UL listed Surge Protective Devices
(SPDs) from live to neutral and from neutral to
earth. Listed SPDs shall be designed for repeated
limiting of transient voltage surges and the
following rated operation conditions: Type 2 (SPDs
permanently connected to the power network and
intended for installation on the load side of the
service equipment); Nominal Discharge Current
(In) 20kA min. For example: FERRAZ SHAWMUT,
STT2240SPG-CN, STT2BL240SPG-CN rated
120Vac/240Vac, (In=20kA). Maximum distance
between installation and reduction is 5m.
• Any device which could be installed inside the
product must comply with the current safety
standards.
• If the installation is NEMA TYPE 4X, the installer
must replace the cable glands of the product with
NEMA TYPE 4X cable glands.
• Power supply to the product must be exclusively
provided by the PoE cable (Power over Ethernet).
• For all connections, use cables that are able to
withstand temperatures of at least 75°C (167°F).
• The product is designed to house only cameras
that are properly certified according to IEC/UL
60950-1 or IEC/UL 62368-1 (7W max).
• A power disconnect device must be included
in the electrical installation, and it must be very
quickly recognizable and operated if needed.
• To connect the power supply line use the
appropriate junction-box (UPTJBUL). For further
information, refer to the product use and
installation manual.
• Use Listed tube crimping lugs for the connection
of the network conductors to the terminals. The
copper tube crimping lugs must be suitable for
the type of installation (from -20°C (-4°F) a +80°C
(+176°F) min., V-0). Copper tube crimping lugs
examples: RP, BP o YP (Cembre).
4 Identification
4.1 Product description and type
designation
The HOV Hi-PoE IPM housing optimally operates
with POE and Hi-POE technology, using the power
supplied by the Ethernet cable as the sole source
of power for all connected devices, thus ensuring
maximum efficiency and flexibility of the network
system as well as user-friendly installation and low
costs.
The innovative IPM (Intelligent Power Management)
system enables extremely quick and easy installation
with the use of a single Ethernet connecting cable.
The Hi-POE IPM system automatically detects all
the options, like heating, fan and illuminator and
then autonomously balances the power to ensure
suitable distribution of the same to the connected
devices. This guarantees the optimal operation of the
IP camera between -30°C (-22°F) and +60°C (140°F),
with heat regulation and cold start (activation at low
temperature).
The IPM system offers an opportunity to refit
analogue systems with already installed housings by
simply changing the slide and internal electronics.
This enables the digital conversion, speeding up
the installation and thereby minimizing costs and
environmental impact.
4.2 Product marking
See the label attached to the product.

Instruction manual - English - EN
5MNVCHOVHPOE_2222_EN
5 Preparing the product for
use
Any change that is not expressly approved
by the manufacturer will invalidate the
guarantee.
5.1 Unpacking
When the product is delivered, make sure that the
package is intact and that there are no signs that it
has been dropped or scratched.
If there are obvious signs of damage, contact the
supplier immediately.
When returning a faulty product we recommend
using the original packaging for shipping.
Keep the packaging in case you need to send the
product for repairs.
5.2 Contents
Check the contents to make sure they correspond
with the list of materials as below:
•Outdoor camera housing
• RJ45 wiring
• Housing equipment:
• Allen wrench
• Spacers
• Cable glands gaskets
• Cable glands (x3)
• Bolts and screws
• Instruction manual
• Desiccant bag
5.3 Safely disposing of packaging
material
The packaging material can all be recycled. The
installer technician will be responsible for separating
the material for disposal, and in any case for
compliance with the legislation in force where the
device is to be used.
5.4 Preparatory work before
installation
5.4.1 Mounting the bracket
The product must be fastened with suitable
equipment. The fastening means must
guarantee mechanical sealing when a force
equal to at least 4 times the weight of the
device is applied.
•Wall mount bracket
•IR illuminator & bracket

EN - English - Instruction manual
6 MNVCHOVHPOE_2222_EN
6 Installation
The product may be interfaced with
devices not manufactured by Hanwha or
VIDEOTEC. It is recommended a test prior
to installation. Hanwha or VIDEOTEC will
not be liable for any installation costs or
lost revenues in the event a compatibility
problem will occur.
6.1 Housing opening
Loosen the 2 screws on the side, turn the cover and
the upper half of the body about the opening hinge
axis.
After installation and wiring, close the
product.
6.2 Slide removal
To remove the slide it is necessary to partially
unscrew the fixing screws as shown in figure.
Move the slide, by sliding it until the holes coincide
with the slide locking screws.
Fig. 1
6.3 Installation of cable glands
Inside the supply are 3 cable glands that must be
installed at the bottom of the housing as shown
in figure. The cable glands that are not used must
be sealed with the cap to avoid water entering the
housing.
Fig. 2
6.4 Installation of the
GEKO IRH illuminator
Maximum power of the illuminator must
not exceed 6W.
To install the illuminator it is necessary to
use the illuminator bracket (OSUPPIR).
The illuminator & bracket are included
with the kit, but may be in separate
packages.
Use the cable glands or the smallest sealing ring to
avoid water entering the housing.
To install the illuminator under a housing, refer to the
installation manual.
For further details on configuration and use refer to
the relative chapter (6.4.4 Connection of the GEKO
IRH illuminator, page 8).

Instruction manual - English - EN
7MNVCHOVHPOE_2222_EN
6.4.2 Ethernet cable installation
Insert the Ethernet cable in the gasket and block it as
shown in figure.
Fig. 5
Fit the gasket (01) to the cable gland M20 (02). Fasten
the cable gland to the bottom of the housing (03)
using the M20 nut (04).
Pay attention to the fixing. Tightening
torque: 7Nm.
Pass the cable with connector RJ45 (05) through the
M20 cable gland (02). Tighten the cable gland cap
(06).
02
01
05
06
04
03
Fig. 6

EN - English - Instruction manual
8 MNVCHOVHPOE_2222_EN
6.4.3 How to install the camera
The correct operation of the equipment,
within the temperature range indicated, is
guaranteed only if you use camera and lens
with temperature limits equal to at least
-10°C and +60°C.
It is possible to install only PoE type
cameras.
Mount the camera using the supplied screws (01) and
spacers (02).
Apply at least one spacer to guarantee electrical
isolation between the slide and the camera.
Position the camera lens close to the glass to avoid
visual interference or optical reflections.
Connect the camera to the J2 connector (PoE OUT)
with the supplied cable (03).
02
01
03
Fig. 7
Refit the slide in its housing and fix the previously
loosened screws.
Fig. 8
6.4.4 Connection of the
GEKO IRH illuminator
Connect the illuminator to the J6 terminal as
described in the diagram below.
1234
Fig. 9
CONNECTION OF THE GEKO IRH ILLUMINATOR
Illuminator Terminal J6
Green (telemetry) 1
Red (telemetry) 2
White (power supply) 3
Black (power supply) 4
Tab. 1
To adjust the lighting threshold of the illuminator
refer to the product's use and installation manual.

Instruction manual - English - EN
9MNVCHOVHPOE_2222_EN
6.4.5 PoE cable connection
Connect the PoE cable from the Power Injector to the
J1 connector.
Fig. 10
Before powering the device, you must set the
maximum power consumption of the housing
operating on dip switch SW1 (7 Configuration, page
9).
7 Configuration
Before powering the device, you must set the
maximum power consumption of the housing
operating on dip switch SW1.
Fig. 13
POWER CONSUMPTION CONFIGURATION
SW1 Maximum power
OFF PoE class 3 (13W max)
ON Hi-PoE class 4 (25W max)
Tab. 2
According to the power consumption, the system
can supply the options described in the table (Tab. 3,
page 10).

EN - English - Instruction manual
10 MNVCHOVHPOE_2222_EN
HOV HIPOE IPM AVAILABLE MODELS AND FEATURES
Operating
temperature
Injector Camera
'BO
Illuminator
From -10°C
(14°F) up to
+60°C (140°F)
PoE class 3
(13W)
PoE max. class
2 (7W)
√
Hi-PoE class 4
(25W)
PoE max. class
3 (13W)
√ √
Tab. 3
8 Switching on
The automatic pre-heating process could
be started whenever the device is switched
on and the ambient temperature is below
0°C (+32°F). The procedure is necessary to
guarantee correct operation of the devices
even at low temperatures. The duration
ranges depending on environmental
conditions (from 60 minutes up to 120
minutes).
During the lighting phase the device reads the
status of the dip switch and automatically detects
all the connected options for the correct energy
management of the housing.
The LEDs shown in the figure allow to check the
product's operating status.
Fig. 14
Refer to the table to identify the operating status.
Note that some components indicated by the
LEDs are not available as part of the kit.
√

Instruction manual - English - EN
11MNVCHOVHPOE_2222_EN
OPERATING STATUS
LED LED Status Apparatus Status
LD1 (Power
supply)
Off The device is not powered
On The device is correctly powered
LD2
(Camera)
Off The camera is not connected or
Cold Start is active
On The camera is correctly powered
1 flashing The camera has a low identification
resistance
2 flashings
The camera has a high
identification resistance
5 flashings
The camera has an excessive
energy consumption
9 flashings The camera requires more energy
than the available
LD3
(Demisting)
Off Demisting was not correctly
detected
1 flashing Standard demisting is inactive
2 flashings The anti-ice system (optional) is
inactive
On Demisting, or anti-ice system, is in
function
LD4 (Heater) Off Heating is not available or power
available is not sufficient
1 flashing Heating is inactive
On Heating is active
LD5
(Illuminator)
Off
The illuminator is not detected or
the available power is not
sufficient
1 flashing The illuminator is correctly
powered (illuminator activation is
controlled by its photocell)
LD6
(Delayed
activation)
Off Heating is not available
1 flashing The pre-heating procedure is
inactive
On The pre-heating procedure is
underway
Tab. 4
Not all feature are avaiilable, depending on model
9 Maintenance and cleaning
9.1 Maintenance
9.1.1 Kit for upgrading of the
equipment
The kit cannot be installed in the housing
versions equipped with wiper.
Remove the slide (01), the electronic board (02) and
the heating (03).
03
01
02
Fig. 15
For kit installation information refer to chapter 6
Installation, page 6.
9.2 Cleaning
9.2.1 Cleaning the window and plastic
parts
Avoid ethyl alcohol, solvents, hydrogenated
hydrocarbide, strong acid and alkali. Such
products may irreparably damage the
surface.
We recommend using a soft cloth with neutral soap
diluted with water or specific products to clean the
glasses lenses.

EN - English - Instruction manual
12 MNVCHOVHPOE_2222_EN
10 Information on disposal
and recycling
The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE) mandates
that these devices should not be disposed of in the
normal flow of municipal solid waste, but they should
be collected separately in order to optimize the
recovery stream and recycling of the materials that
they contain and to reduce the impact on human
health and the environment due to the presence of
potentially hazardous substances.
The symbol of the crossed out bin is marked
on all products to remember this.
The waste may be delivered to appropriate collection
centers, or may be delivered free of charge to the
distributor where you purchased the equipment at
the time of purchase of a new equivalent or without
obligation to a new purchase for equipment with size
smaller than 25cm (9.8in).
For more information on proper disposal of these
devices, you can contact the responsible public
service.
11 Technical data
11.1 General
Constructed from aluminium
Sunshield in ABS
Epoxypolyester powder painting, RAL9002 color
Stainless steel external screws
11.2 Mechanical
Internal usable area (WxHxL): 100x70x250mm
(3.9x2.7x9.8in)
Cable glands: 1xM12, 1xM16, 1xM20
Glass window extra clear
• Dimensions (WxH): 118x75mm (4.6x2.95in)
Unit weight: 3.1kg (6.6lb)
11.3 Electrical
Power absorbed in input: PoE class 3 (13W) or Hi-PoE
class 4 (25W) selectable from dip switch
Available power for camera (PoE IN class 3): PoE Class
2 (7W)
Available power for camera (Hi-PoE IN class 4): PoE
class 3 (13W)
Data line: 10/100Base-T
Illuminator GEKO IRH, low power: 6W
Compatible with IEEE 802.3af, IEEE 802.3at/PoE Plus
Compatible with standard PoE/PoE+ Power
Injectors, not included.
11.4 Environment
For indoors and outdoors installation
Operating temperature: From -10°C (14°F) up to
+60°C (140°F)
11.5 Certifications
Electrical safety (CE): EN60950-1, IEC60950-1,
EN62368-1, IEC62368-1
Electromagnetic compatibility (CE): EN50130-4,
EN61000-6-3, EN55022 Classe B, FCC Part. 15 Class B
Outdoor installation (CE): EN60950-22, IEC 60950-22
IP protection degree (EN60529): IP66
IK protection degree (EN62262): IK10 (except for the
front glass)
Salty fog resistance: ISO9227, to 1000 hours
UL certification: cULus Listed,TYPE 4X
EAC certification

Instruction manual - English - EN
13MNVCHOVHPOE_2222_EN
12 Technical drawings
The indicated measurements are expressed in millimetres.
100
70
250
70
70 189
40 114
514 176
131
158
413 165
70
62
70
401
115
142
A - A
A
B - B
A
B
B
USABLE
AREA
USABLE AREA
Fig. 16 HOV HiPoE IPM.