HAPPY LIVING G9206A-SB-02 User manual

OWNER’S MANUAL
G9206A-SB-02 MOBILE GAS BARBECUE
WITH SIDE BURNER
Dansk manual finds påmoreland.dk

Technical Information
Appliance Code
G9206A-SB-02
Total Heat Input
(All Gas Categories)
18.2 kW ( 1326 g/h )
Gas Category
I3(B/P)30
Types of Gas
LPG GAS MIXTURES
Gas Pressure
30 mbar
Injector Size
Main : 0.75 mm Side : 0.85 mm
Identification Code
359CL1116
FOR USE OUTDOORS AND IN WELL VENTILATED AREAS
WARNING: ACCESSIBLE PARTS MAY BE VERY HOT, KEEP YOUNG CHILDREN AWAY
READ THE INSTRUCTION LITERATURE BEFORE USING THE APPLIANCE
Ignition: Main Burner : Single shot piezo ignition unit which lights a transient pilot
Side Burner : Single shot piezo ignition unit
IMPORTANT:
Read the following instructions carefully and be sure your barbecue is properly installed,
assembled and cared for. Failure to follow these instructions may result in serious bodily injury
and/or property damage.
If you have any questions concerning assembly or operation, consult your dealer or LPG Gas
Company.
When used always place the appliance and cylinder on flat level ground.
Never light the appliance with the HOOD in the closed position.
Never attempt to light or use the side burner with the lid in the closed position as a hazardous
condition could arise and damage to the appliance will occur.
NOTE FOR CONSUMER: Retain for future Reference

26
23
18 17
31
30
29
28
27
25
24
21
20
19 16
15
14
13
12
11
7
10
9
8
3
5
6
4
2
1
22
32

Side Panel
Cart Bracket
Hood
Warming Rack
1
2
1
1
1
1
2
1
2
1
1
2
1
1
2
1
1
1
2
6
1
1
2
1
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
Side Table
3
2
1
QTY
Figure
Description
NO.
QTY
Figure
Description
NO.
4
Grease Tray 1
Side Handle
Back Right Leg
Front Right Leg
Catser
Door Axle
Door Handle
Left Door
Bottom Tray
Lock Caster
Door Bracket
Back Panel
Front Left Leg
Back Left Leg
Flame Tamer
Cooking Grid
Body
Right Door
2
Knob base
Knob
Magnet

Electric Pole
Side Burner
Side Burner Rack
1
1
1
31
30
29
28
QTY
Figure
Description
NO.
1
27
Side Burner Cover
Side Burner Table 1
48
A
B
C6
D2
E2
Clip 2
Screw
(M6X10)
Screw
(M3X10)
Nut (M3)
Screw
(M4X10)
4
Handle Base
32

A
A
A
A
A
A
A
A
A
A
A
A
A
Back(right)
Front(right)
Back(left)
4PCS
16PCS
STEP 2
STEP 1
Front(left)
M6X10
A
M6X10

M6X10
A
A
A
A
A
D
E
4PCS
M3X10
DM3
E
2 PCS
2 PCS
Mut
STEP 3
STEP 4

M6X10
A
M6X10
A
AA
A
A
A
A
4PCS
8PCS
STEP 5
STEP 6

M6X10
A
AA
AA
8PCS
STEP 7
STEP 8

STEP 10
STEP 9
AM6X10 4Pcs

CM4X10 2Pcs
C
C
STEP 11
STEP 12

C
CC
C
C
M4X10 2Pcs
M4X10 2Pcs
C
STEP 13
STEP 14

B
B
STEP 15
Clip 2Pcs

CONNECTING THE GAS CYLINDER TO THE APPLIANCE
This appliance is only suitable for use with low pressure Butane or Propane gas or LPG mixtures,
fitted with the appropriate low-pressure regulator via a flexible hose. The hose should be secured
to the regulator and the appliance with hose clips. This barbecue is set to operate at a 28 mbar
regulator with Butane gas and a 37 mbar regulator with Propane gas, 30 mbar for LPG mixtures or
50 mbar for LPG mixtures. Please consult your LPG dealer for information regarding a suitable
regulator for the gas cylinder.
Regulator and Hose
This item is not supplied with the barbecue, but replacements are available from your
equipment retailer or an authorised LPG gas stocket. Use only regulators and hose approved
for LP Gas at the above pressures. The life expectancy of the regulator is estimated as 10
years. It is recommended that the regulator should be changed within 10 years of the date of
manufacture.
The use of the wrong regulator or hose is dangerous, always check that you have the correct
items before operating the barbecue.
The hose used must conform to the relevant standards for the country of use. The length of the
hose must be 1.5 metres (maximum). Worn or damaged hose must be replaced. Ensure that
the hose is not obstructed, kinked or in contact with any part of the barbecue other than at its
connection.
Storage of Appliance
The appliance should be only allowed to store indoors when appliance is disconnected and
removed from the cylinder. When the appliance is not in use for a period of time it should be
stored in its original packaging and stored in a dry, dust free environment.
Gas Cylinder
The gas cylinder should not be dropped or handled roughly. If the appliance is not in use, the
cylinder must be disconnected. Replace the protective cap on the cylinder after disconnecting
the cylinder from the appliance.
Cylinders must be stored outdoors in an upright position and out of the reach of children. The
cylinder must never be stored where temperatures can reach over 50oC. Do not store the
cylinder near flames, pilot lights or other sources of ignition. DO NOT SMOKE NEAR THE
CYLINDER(S).
This barbecue is designed for use outdoors only, away from any flammable materials. It is
important that there are no overhead obstructions and that there is a minimum distance of 1m
from the side and rear of the appliance. It is important that the ventilation openings of the
appliance are not obstructed. The barbecue must be used on a level, stable surface. The
appliance should be protected from direct draughts and should be positioned or protected
against direct penetration by any trickling water (e.g. rain).
Parts sealed by the manufacturer or his agent must not be altered by the user. No modifications
should be made to any part of this barbecue and repairs and maintenance should only be carried out
by a CORGI registered service engineer.
Connection to Appliance

Before connection, ensure that there is no debris caught in the head of the gas cylinder,
regulator, burner and burner parts. Spiders and insects can nest within and clog the
burner/venturi tube at the orifice. A clogged burner can lead to a fire beneath the appliance.
Clean burner holes with a heavy-duty pipe cleaner.
Fit the hose to the appliance using a spanner to tighten it onto the connection thread. If the
hose is replaced, it must be secured to the appliance and regulator connections with hose clips.
Disconnect the regulator from the cylinder (according to the directions indicated on regulator)
when the barbecue is not in use.
The barbecue must be used in a well-ventilated area. Do not use indoors or garage. ONLY
USE THIS BARBECUE OUTDOORS.
BEFORE USE CHECK FOR LEAKS
Never check for leaks with a naked flame, always use a soapy water solution
CHECK FOR LEAKS
Make 2-3 ounces of leak detecting solution by mixing ¼ washing up liquid with 3/4 water.
Ensure the control valve is OFF.
Connect the regulator to the cylinder and ON/OFF valve to the burner, ensure the connections
are secure then turn ON the gas.
Brush the soapy solution onto the hose and all joints. If bubbles appear you have a leak, which
must be rectified before use.
Retest after fixing the fault.
Turn OFF the gas at the cylinder after testing.
If leakage is detected and cannot be rectified, do not attempt to repair leakage but consult your
gas dealer.
Lighting instructions for main burner
1. Open the lid and make sure that all burners are in the OFF position
2 Connect the regulator to the gas bottle. Turn the gas supply to “ON” position on the regulator.
Use soapy water to check if there is any gas leakage between the Bottle and the regulator.
3 Push down the second control knob and turn it anti-clockwise to position, this will light the
pilot and the second main burner.
4 Turn other burners via pilot .
5 If the burner fails to ignite, turn the control knob off(clockwise) and also turn the cylinder valve
off. Wait 5 minutes and repeat step 3.
6 Adjust the heat by turning the knob to the High/Low position.
7 To turn OFF the barbecue, turn the cylinder valve or regulator switch to the “OFF” position and
then turn the control knob on the appliance clockwise to the “OFF” position.
Warning: If any burner fails to ignite, turn the control knob off (clockwise) and also turn the cylinder
valve off. Wait five minutes before attempting to relight.
Before cooking for the first time, operate the barbecue for about 15 minutes with the lid closed and
the gas turned on HIGH. This will „heat clean‟ the internal parts and dissipate odour from the
painted finish.

Lighting instructions for side burner
1. Open the lid.
2. Push down the control knob and turn it anti-clockwise to position to light the burner
3. If the burner is not lit within 5 seconds, turn the knob to OFF position, and repeat step 2.
4. If the burner fails to ignite, turn the control knob off (clockwise) and also turn the cylinder valve
off. Wait 5 minutes and repeat step 2.
5. To turn the barbecue “OFF” , turn the cylinder valve or regulator switch to the “OFF” position
and then turn the control knob on the appliance clockwise to the “OFF” position.
Note: A loose connection between side burner and valve will not cause personal injury, a flame
can only occur with a mixture of gas and oxygen
Warning: If any burner fails to ignite, turn the control knob to off position (clockwise) and also turn
the cylinder valve off. Wait for five minutes before attempting to light the barbecue again.
CLEANING AND CARE
CAUTION:
All cleaning and maintenance should be carried out when the barbecue is cool and the fuel
supply turned OFF at the gas cylinder.
CLEANING: “Burning off” the barbecue after every use (for approx. 15 minutes) will keep
excessive food residue to a minimum
OUTSIDE SURFACE
Use mild detergent or baking soda and hot water solution. Non-abrasive scouring powder can
be used on stubborn stains, then rinse with water.
If the inside surface of the barbecue lid has the appearance of pealing paint, baked on grease
build-up has turned to carbon and is flaking off. Clean thoroughly with strong, hot soapy water
solution. Rinse with water and allow to completely dry. NEVER USE OVEN CLEANER.
INTERIOR OF BARBECUE BOTTOM
Remove residue using brush, scraper and/or cleaning pad, then wash with soapy water solution.
Rinse with water and allow to dry.
COOKING GRID
Use a mild soapy water solution and rinse with water. Non-abrasive scouring powder can be used
on stubborn stain.
CLEANING THE BURNER
Turn the gas OFF at the control knob and disconnect the cylinder.
Remove cooling grate.
Clean the burner with a soft brush or blow clean with compressed air and wipe with a cloth.
Clean any clogged parts with a pipe cleaner or stiff wire (such as an opened paper clip).
Inspect burner for any damage (cracks or holes). If damage is found, replace with a new burner.
Re-install the burner, check to ensure that the gas valve orifices are correctly positioned and
secured inside the burner inlet (venturi).