Haugen MFSH-6 User guide

Fork Mounted Swivel Hooks
Installation and Safety Manual
www.haugenattachments.com
Model: MFSH-6
Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
DOC# MFSH62015
Marv Haugen Enterprises Inc. * 1851 Heartland Ave. * Casselton ND 58012 * Phone: [phone]

Marv Haugen Enterprises * 1851 Heartland Ave * Casselton ND 58012 Phone: [phone]
Swivel Jibs
Haugen Swivel Hooks are designed for use on rough terrain extendable or straight mast forklifts, and
industrial lift trucks. They have been tested , proven and rated for the Load Capacities as shown on
the Swivel Hook. Haugen Attachments has been building Industrial Swivel Hooks for many years,
these units have proven themselves durable and extremely safe throughout the United States and
Canada
Swivel Hooks are designed to hold a Swivel Hook at a standard 24” load center. Forklifts are nor-
mally designed with a 24” loader center. Since the swivel hook is located at the 24” loader center
the forklifts load chart will normally apply, less the empty weight of the attachment, rigging and the
weight of the load. A seperate down rated load chart should not be needed for the forklift.
Note the rating of the Swivel Hook does not reect the rating of the Forklift or Telehandler. The
total load must never exceed the rating of the Forklift or Telehandler.
Before you use this Swivel Hook you must read and understand the
Operator’s Manual
Keep a copy of this manual on the Swivel Hooks at all times
If you have questions call us at 1-877-580-6218
Engineering Certication
The Haugen Swivel Hooks have been designed and built to comply with the ANSI/TISDF B56.6-
2011 and the CSA B335 safety standards. The Swivel Jibs have been tested and certied by a third
party Certied Professional Engineer. A copy of their report is at the back of the owners manual. If
required a copy of the full engineering report is available upon request.
Thank you for choosing a Haugen Swivel Hook
Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]

Installation Safety Pins
The Swivel Hooks are very easily installed by inserting your forklift tines
fully into the pockets so the ears extend behind the Forks. Then install
the safety retainer pin behind the fork and insert the security clip. ( As
Shown on the diagram) The safety retainer pins are chained to the Jib
to prevent loss of the pins. These must be properly installed and secured
before using the Jib. Note: Swivel Hook Frame, Hook and retainer pins
should be fully inspected before every use.
- Operating Rules for Swivel Hooks -
Inspection
1. Check the Swivel Hook, Latch, Bolt and Sleeve making sure that it is properly installed and in
good working condition.
2. Check the Bolt and sleeve for any wear or distortion
3. Safety pins must be installed and secured with the cotter pin.
4. Check the Swivel Hook Frame for any excessive wear, cracked or broken welds.
5. Check each of the holes for any elongation.
6. The Swivel Jibs load capacity rating and empty weight decals must be present and legable.
7. The operator must have read and understands the operators manual.
Installing on a Lift Truck
1. Secure the safety pins behind the heel of each fork.
2. Optional Safety chains when used are only to be used in addition to the safety retainer pins, not
in lieu of.
3. Disable any hydraulic functions to the Forklift Carriage. Such as tilting or swinging functions.
4. Position the fork tines so that the Swivel Hook will hold the load centered on the Forklift.
Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
Marv Haugen Enterprises * 1851 Heartland Ave * Casselton ND 58012 Phone: [phone]

General Operating Rules
1. Inspections as stated above must be made prior to each use of the Swivel Hook
2. Before each use make sure the Swivel Hook is properly installed on the fork tines and that the
hook is secured to the Swivel Hook frame and the bolt is tight.
3. Determine that the load your lifting is within the capabilities of the Swivel Jib and the capacity
of the Lift Truck. Never exceed the capacities on either the Forklift or the attachment, Remember
that capacity of the Forklift decreases when the load is raised and especially with Telehandlers when
the load is extended.
4. Before picking up a load make sure that it is balanced and level. Make sure that the slings, straps or
any other rigging is properly secured and is not twisted or entangled in anyway.
5. Do not pull loads. The Swivel Jib is designed for vertical lifting ONLY.
6. Carry all loads low and use tag lines to keep loads from swinging.
7. Be sure forklift is on a level /rm surface before raising the load.
8. Forks should always be level or slightly tilted back, never tilted forward when using the Swivel Jib.
9. The Forklift operator must remain in the seat at the controls with the engine running whenever there
is a load on the Swivel Jib.
10. Only qualied and trained personal should operate the forklift. Operators should know and follow
all local, state and federal safety regulations
11. All safety regulations must be followed at all times.
12. Any personal working around the Swivel Jib must wear hard hats and steel toed boots
13. When lifting loads there should be no personel within a minimum of ten feet in all directions of the
fall zone, never put yourself or any part of your body under a suspened load.
14. Do not use the Swivel Jib in anyway to lift personal.
15. Refer to the Forklift’s operators manual for more information on handling elevated loads and
additional safety tips.
Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]

Note: The capacity decals reects the capacity of the Swivel Hook only and does not reect the
capacity of the forklift nor the maximum load that can be safely handled by a particular
forklift.
Model = MFSH-6
Empty Weight = 137 lbs
Vertical Center of Gravity = 1.35”
Horizontal Center of Gravity = 15.98”
Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
WARNING
6000 LBS Capacity
* These lift capacity ratings are for the Swivel Jib only. The lifting capacity is
ultimately determined by the host machine. Never lift more than the operating
capacities of this Swivel Jib or the capacities stated by the Manufacturer
of the host machine. MFSH-6

Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
Copy of the Swivel Hooks
Engineering Certication
report. A full detailed report
is available upon request

Marv Haugen Enterprises warrants it’s products , under normal use and maintenance, to be free from defects in
material and workmanship for a period of one year from the purchase date from an authorized Haugen Dealer.
e limited warranty is extended only to the original purchaser of Haugen ProductsWarranty Statement
1. During the applicable warranty period, Haugen at it’s option , will repair or replace any part determined
by Haugen to be defective. Such repair or replacement shall take place at Haugen’s factory or a
location designated by Haugen. Under no circumstances shall Haugen be obligated for the cost of any
repair or replacement by anyone other than Haugen without its express written consent.
2. Parts may not be returned without the express written authorization from Haugen.
3. Some purchased components including but not limited to hooks, cylinders, and hydraulic motors are
subject to inspection and warranty of the respective manufacturers.
4. is warranty is void if any attempt is made to make eld repairs. Make sure to leave the product in its
original failed condition.
5. To make a claim under this warranty rst contact your authorized Haugen dealer. e Haugen dealer
shall complete the warranty claim form and obtain written authorization from Haugen to return parts.
All warranty claims must include detailed information regarding make and model of the vehicle on which
the Haugen product was mounted, hours of use, description of events that led up to the failure, and any
other information helpful in reviewing this claim. All warranty returns must be prepaid. Shipments
arriving at our factory on a freight collect basis will be refused by our recieving department. e freight
charges will be credited if the parts are determined by haugen to be defective, and the associated freight
costs in returning those parts will be prepaid by Haugen.
6. Products or parts thereof which, as determined by Haugen’s examination, show wear from normal use,
been improperly operated, damaged by accident or negligence, eld repaired, altered or modied are
not considered defective in material or workmanship and are not covvered by this warranty. is
warranty does not obligate Haugen to bear any cost of labor for eld repair, replacement, testing, or
adjustment nor damaged caused by accident, abuse, misuse, or environmental elements.
7. Any parts or labor required to repair or replace parts not covered under this warranty will be charged to
the customer. Parts repaired or replaced by Haugen are then covered by this warranty only for the
remainder of the original warranty as if such parts were original parts.
8.. Haugen reserves the right to change its specications and designs at any time.
is warranty is exclusive and in lieu of all other express warranties, if any including implied warranties of
merchantability and tness for a particular purpose. It shall not extend beyond the duration of the expressed
warranty provided herein and the remedy for violations of any implied warranty shall be limited to repair or
replacement of the defective part pursuant to the terms contained herein. No employee, dealer, salesman,or
representative is authorized to change this warranty in any way or grant any other warranty. Haugen shall not
be liable for any consequential, incidental, or punitive damages, losses or expenses, including those resulting
from or caused by any defects.
Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
Warranty Statement

Marv Haugen Enterprises Inc. * 1851 Heartland Ave. * Casselton ND 58012 * Phone: [phone]
www.haugenattachments.com