Havis C-DMM-3016 User manual

C-DMM-3016_INST_4-20
INSTALLATION INSTRUCTIONS
C-DMM-3016 Flip up Dash Monitor Mount
2011 - 2020 Chevrolet Express/ GMC Savanna van
Always!
 Read all instructions before installing any Havis, Inc. products.
 Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes!

Use hardware provided with install kit
PARTS and MOUNTING HARDWARE:
QTY DESCRIPTION PART#
1 Driver side inner mounting bracket CM010204-DS
1 Passenger side inner mounting bracket CM010204-PS
1 Driver side outer mounting bracket CM010205-DS
1 Passenger side outer mounting bracket CM010205-PS
1 VESA rotator plate CM010471
2 1/4" x 3/4" Carriage bolts GSM32000
1 PVC washer CM010648
2 1/4" Nylock nut GSM30016-1
2 1/4" Plastic flat washer CM86600
6 3/8” Dome plug GSM20013
2 1/4" Flat washer GSM31005
4 1/4" Star washer GSM31035
5 #8 Star washer GSM31033
5 8/32 x 1/2" Phillips screw GSM33110
2 1/4" x 3/4" Hex head bolt GSM33001
8 1/4" x 3/4" Phillips head bolt GSM33124
Notes:
1. The C-DMM-3000 swivel plate accepts C-MM-301 offset bracket used with C-MM-2XX
adaptors.
2. C-MM-2XX series adaptor brackets are not needed for most VESA 75 and other Havis Docking
Station mounting applications.
3. CM010471 VESA rotator plate gives additional positioning options, but is not required
depending on mounting preference.
TOOLS REQUIRED:
•Ratchet Wrench • Socket Set • 7/16” Open End Wrench
• Phillips Screwdriver (short) • Dash panel removal tool

C-DMM-3016_INST_4-20
C
-
DMM
-
3016
CM010204-DS
CM010204-PS
CM010205-PS
CM010205-DS
GSM33001
GSM31035
GSM33124
GSM33124
GSM20013
CM010471
CM010648
GSM30016-1
GSM31005
CM86600
GSM32000

C-DMM-3016_INST_4-20
OEM dash prior to installation
Unplug and remove radio from dash.
Unscrew AM/FM radio from dash.
Screws will be reused
7mm head screw
Carefully remove driver side lower dash panel. It
may not be necessary to be completely removed.
Detach center dash panel and pull out passenger
side only as far as needed to remove the AM/FM
radio.
Carefully remove passenger side lower dash panel.
It may not be necessary to be completely removed.
(10
mm socket)

C-DMM-3016_INST_4-20
Unscrew and lower OEM HVAC control.
Screw will be reused.
7mm head screw
Reinstall previously removed dash.
Attach inner passenger side mounting bracket to
dash using previously removed OEM hardware.
Unplug all connectors from rear of OEM HAVC
controller
Attach inner driver side mounting bracket to dash
using previously removed OEM hardware.
Remove plastic radio mounting ring.
This will not be reused.

C-DMM-3016_INST_4-20
Attach outer passenger side mounting bracket.
This bracket has a bend at the top that is designed
to hook around the top on the inner bracket.
Re-install HVAC controller using 8-32 x 1/2" screw
and #8 star washer.
Leave hardware loose
Attach using 8-32 x 1/2" screws and #8 star
washers.
Leave hardware loose
Attach top mount hole with 1/4" x 3/4” Hex head bolt
and 1/4" Star washer.
Phillips head bolt shown in picture for reference only
Plug OEM radio back in and slide into dash
opening.
Attach lower mount holes with 1/4" x 3/4" Phillips
head bolt. Repeat on opposite side.

C-DMM-3016_INST_4-20
Place frame over radio, HVAC controller, and
outer mounting brackets.
Route wiring as needed a
long the side of
the DMM
frame
using wire tie holes. Test up / down and side to side motion
to confirm wires have adequate slack and strain relief.
Installation is now complete
Determine desired position for your specific computer and
attach to DMM swivel plate using 1/4"x 3/4” carriage bolts,
PVC spacer, nylon washers, steel washers, and nylock nuts.
Tighten so that the dock rotates smoothly.
Tighten using 1/4" x 3/4" Phillips head bolts and
#10 star washers.
Position VESA plate on back of Device as desired.
Attach VESA plate with carriage bolts to the back
of the dock. The gray PVC washer will go between
this bracket and the DMM swivel plate.
Tighten radio and HVAC controller through access
holes in front of frame. Cover holes with 3/8” dome
plugs supplied with kit.